Nissan Almera - GSM-Forum

Julesd · 07-27-2012, 10:47

Hi Guys,
I have a 2004 Nussan Almera eith the separate lower CD tuner PN-2598M
with no sound at all. The unit does not even get warm. Can anyone help please? I presume O/P stage ****n but not sure.

Thanks.
Regards, Jules.

grassseed · 07-29-2012, 18:56

In a lot of occasions with this fault I have found a 47 ohm smd resistor located on component side of pcb to be either open or d/g. It is on r h s of pcb and near to front facia .
Maybe the opic is faulty but I have only had to replace it a couple of times.
Can anyone supply me with a diagram of loom so I can power these on my bench-- my son is getting annoyed with me because I currently use his Almera to test them----- thank you

Julesd · 07-29-2012, 20:15

Thanks for the reply Grassseed.
I will have a look inside and get back to you.

regards, Jules.

Julesd · 08-30-2012, 14:50

I have replaced that resistor which read OK anyway but still no sound.
Is there anything else I could try?

Thanks.
Regards, Jules.

07-27-2012, 10:47	#1 (permalink)
Julesd Freak Poster Join Date: Dec 2006 Location: Liverpool UK Posts: 165 Member: 402904 Status: Offline Thanks: 6 Thanked 21 Times in 8 Posts	Nissan Almera Hi Guys, I have a 2004 Nussan Almera eith the separate lower CD tuner PN-2598M with no sound at all. The unit does not even get warm. Can anyone help please? I presume O/P stage ****n but not sure. Thanks. Regards, Jules.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Nissan ( Blaupunkt )	Bypx	CAR Electronics	11	07-28-2006 16:21
Nissan Primera P11 Service Manual > Here !	Patrick	CAR Electronics	3	05-19-2006 12:09
blaupunkt code for nissan car radio	Junaid_UK	CAR Electronics	0	05-12-2006 22:42
radio code for nissan micra	Junaid_UK	CAR Electronics	2	04-25-2006 19:44
need code for nissan/clarion	patric	CAR Electronics	0	03-14-2006 17:48

07-29-2012, 18:56	#2 (permalink)
grassseed Junior Member Join Date: Jul 2011 Location: Hoan, sth Ireland Posts: 27 Member: 1624349 Status: Offline Thanks: 0 Thanked 2 Times in 2 Posts	In a lot of occasions with this fault I have found a 47 ohm smd resistor located on component side of pcb to be either open or d/g. It is on r h s of pcb and near to front facia . Maybe the opic is faulty but I have only had to replace it a couple of times. Can anyone supply me with a diagram of loom so I can power these on my bench-- my son is getting annoyed with me because I currently use his Almera to test them----- thank you

07-29-2012, 20:15	#3 (permalink)
Julesd Freak Poster Join Date: Dec 2006 Location: Liverpool UK Posts: 165 Member: 402904 Status: Offline Thanks: 6 Thanked 21 Times in 8 Posts	Thanks for the reply Grassseed. I will have a look inside and get back to you. regards, Jules.

08-30-2012, 14:50	#4 (permalink)
Julesd Freak Poster Join Date: Dec 2006 Location: Liverpool UK Posts: 165 Member: 402904 Status: Offline Thanks: 6 Thanked 21 Times in 8 Posts	I have replaced that resistor which read OK anyway but still no sound. Is there anything else I could try? Thanks. Regards, Jules.