RCD 300/500 Engineering mode - GSM-Forum

rz5g03 · 06-03-2010, 18:24

Does anyone know how to get into the engineering mode for an RCD 300 or RCD 500 Radio? I can get to a diagnostic screen by holding down the menu button for 5 seconds, but there is an engineering mode with a lot more data and some controls. Not sure how to get there or if it might be calibrated off in the EEPROM settings. Any help is appreciated.

dvb_gsm · 06-03-2010, 23:23

Hi....

precise the model ??????????

-= CODEDRADIO =- Base navigation

rz5g03 · 06-04-2010, 16:20

VW RCD 500 Chrome BVX
Blaupunkt 7 644 255 360
HW 008
SW 0015

Is that the information you're looking for?

stt · 06-04-2010, 18:09

If I understand good , you now see any data on the screen and want to return the radio to its previous state ???

rz5g03 · 06-04-2010, 18:53

No. I'm trying to get the radio into the engineering mode to have access to more information about the reception conditions, and some control over the reception modes. The RCD 300/500 have a background scanning mode that uses 1 of the tuners to scan for alternate frequencies, and I want to disable that so both tuners are always used for phase diversity for best reception performance.

06-03-2010, 18:24	#1 (permalink)
rz5g03 Junior Member Join Date: May 2010 Location: Indiana, USA Posts: 5 Member: 1306501 Status: Offline Thanks Meter: 0	RCD 300/500 Engineering mode Does anyone know how to get into the engineering mode for an RCD 300 or RCD 500 Radio? I can get to a diagnostic screen by holding down the menu button for 5 seconds, but there is an engineering mode with a lot more data and some controls. Not sure how to get there or if it might be calibrated off in the EEPROM settings. Any help is appreciated.

06-03-2010, 23:23	#2 (permalink)
dvb_gsm No Life Poster Join Date: Jul 2004 Location: EL JEM/Tunisia Age: 56 Posts: 802 Member: 71213 Status: Offline Thanks Meter: 120	Rcd 300 ??? Hi.... precise the model ?????????? -= CODEDRADIO =- Base navigation

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Need 8210 v 5.28 flash 200-300 1MB ...	Kilowat	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	08-29-2001 18:15
3210 Vibra-Mode with pclocals	mongoq	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	07-23-2001 15:54
8290v506 backup on address 280-300	dgtulga	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	07-16-2001 19:23
Reverse engineering MCU software	kodo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	04-21-2001 11:18

06-04-2010, 16:20	#3 (permalink)
rz5g03 Junior Member Join Date: May 2010 Location: Indiana, USA Posts: 5 Member: 1306501 Status: Offline Thanks Meter: 0	VW RCD 500 Chrome BVX Blaupunkt 7 644 255 360 HW 008 SW 0015 Is that the information you're looking for?

06-04-2010, 18:09	#4 (permalink)
stt No Life Poster Join Date: Sep 2006 Location: BG,Plovdiv Posts: 2,048 Member: 351183 Status: Offline Thanks Meter: 768	If I understand good , you now see any data on the screen and want to return the radio to its previous state ???

06-04-2010, 18:53	#5 (permalink)
rz5g03 Junior Member Join Date: May 2010 Location: Indiana, USA Posts: 5 Member: 1306501 Status: Offline Thanks Meter: 0	No. I'm trying to get the radio into the engineering mode to have access to more information about the reception conditions, and some control over the reception modes. The RCD 300/500 have a background scanning mode that uses 1 of the tuners to scan for alternate frequencies, and I want to disable that so both tuners are always used for phase diversity for best reception performance.