GX15 , GX30 cable - GSM-Forum

vipermat · 08-17-2005, 21:40

Helo,
I have Sharp GX 15 and GX30.
I have cable USB for Nec e228 too. Can I used them? Cable for Nec have this same connetors.
Maybe somebody have schematic cable for sharp.
Thx

best regards

vipermat · 08-24-2005, 21:34

please help me. I can't found schematic.

B&R

BlackyP · 08-24-2005, 21:37

Quote:

Originally Posted by vipermat

please help me. I can't found schematic.

B&R

Please look at other post from me

iflorinus75 · 08-24-2005, 23:50

Yes you can use USB cable for NEC to unlock Sharp. You need to make only 2 modification. When you will look at the cable you will see that at the phone connector there are 2 pins soldered and next to them there are other 3 pins soldered. In order to use NEC cable for Sharp you only need to unsolder the pins mentioned above and your cable will work for Sharp. This solution is tested.

BlackyP · 08-25-2005, 09:02

here is a GX30 Pinout.

Platijet · 08-25-2005, 10:47

@ iflorinus:
this cable is for flashing gx15 and gx25,for unlock this models you need a simple data USB cable(is the same without wirings)

for gx30 and tm100,unlock and flash cable is the same.must be com cable(not USB) with 3V external power.

BlackyP · 08-25-2005, 12:48

Try it times with this cableplan.

Platijet · 08-25-2005, 13:48

this wiring(12V on pin 3) can be dangerous for the phone.is better to put 3V external voltage,or 5V tooken from LM7805(Lo)

vipermat · 08-27-2005, 09:29

Thank for reply.
You say that:
for unlock GX15/GX25 i must have simple USB cable(unsoldering 4,5 and 8,9,10)
for unlock GX30 i must have com cable.
Correct I undestand?( My english is not good).

Another Q:

Can I use simple USB cable to normal comunicate( ogrinal sharp software or diferental) with GX15 or maybe GX30?

Platijet · 08-27-2005, 10:18

Quote:

Originally Posted by vipermat

Thank for reply.
You say that:
for unlock GX15/GX25 i must have simple USB cable(unsoldering 4,5 and 8,9,10)
for unlock GX30 i must have com cable.
Correct I undestand?( My english is not good).

right....

Quote:

Originally Posted by vipermat

Another Q:

Can I use simple USB cable to normal comunicate( ogrinal sharp software or diferental) with GX15 or maybe GX30?

for original sharp software(suite or handset manager) only simple USB cable can work for 15/25/30

crusher · 02-22-2006, 13:27

you dont need unsolder 4 and 5, it can be used to unlock the phone as well. maybe you dont need to unsolder 8,9,10 but this is not tested!!

but 4 and 5 connected WORKS TESTED for UNLOCK and FLASH in MOST cases.

sergo_zmeia · 02-22-2006, 13:50

if U need to unlock those phones just use NEC8i usb cable..no need to change anything..
WBR!
sergo_zmeia

Platijet · 02-22-2006, 14:00

check stickys threads about cables

sergo_zmeia · 02-22-2006, 14:50

Mr.Platijet, guess Ur previous replay was for me...I realy do respect Ur solutions here..but do believe me the only cable I use to unlock sharp gx15,25,30 is NEC8...
WBR!
sergo_zmeia

Platijet · 02-22-2006, 15:27

my previus post was for all members.that i'm trying to say is that using flash USB cable(NEC 3G)you don't have autoignition(especialy user code on SPST).same case for GX30 usb/com cable.

08-17-2005, 21:40	#1 (permalink)
vipermat Junior Member Join Date: Sep 2004 Age: 38 Posts: 23 Member: 80949 Status: Offline Thanks Meter: 0	GX15 , GX30 cable Helo, I have Sharp GX 15 and GX30. I have cable USB for Nec e228 too. Can I used them? Cable for Nec have this same connetors. Maybe somebody have schematic cable for sharp. Thx best regards

02-22-2006, 13:50	#12 (permalink)
sergo_zmeia Freak Poster Join Date: Jun 2003 Location: Bulgaria Age: 48 Posts: 471 Member: 32284 Status: Offline Thanks Meter: 4	Hi! if U need to unlock those phones just use NEC8i usb cable..no need to change anything.. WBR! sergo_zmeia

02-22-2006, 14:50	#14 (permalink)
sergo_zmeia Freak Poster Join Date: Jun 2003 Location: Bulgaria Age: 48 Posts: 471 Member: 32284 Status: Offline Thanks Meter: 4	Hi! Mr.Platijet, guess Ur previous replay was for me...I realy do respect Ur solutions here..but do believe me the only cable I use to unlock sharp gx15,25,30 is NEC8... WBR! sergo_zmeia

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GX15 GX30 serial pinout needed	FreaX	Sharp	13	11-04-2004 14:19
Here's Crack/Trick for Gx107gx20/gx15/gx30 unlocker...Enjoy ;)	the_frightener	Sharp	19	10-01-2004 21:53
Nec_reader_code & Sharp Gx10,Gx10i,Gx20,Gx15,Gx30	GMX@cool	Exchange Section	4	09-28-2004 08:42
*SwS-RedboX - LG8110 - SHARP GX15 - GX30 - ALL LG - NEC - PHILIPS - BENQ - MAXON*	julvir	Main Sales Section	0	09-18-2004 14:39
sharp gx15 gx30	labelle	Main Sales Section	0	09-04-2004 01:18

08-24-2005, 21:34	#2 (permalink)
vipermat Junior Member Join Date: Sep 2004 Age: 38 Posts: 23 Member: 80949 Status: Offline Thanks Meter: 0	please help me. I can't found schematic. B&R

08-25-2005, 13:48	#8 (permalink)
Platijet No Life Poster Join Date: Apr 2003 Location: Greece Age: 47 Posts: 3,358 Member: 26279 Status: Offline Thanks Meter: 274	this wiring(12V on pin 3) can be dangerous for the phone.is better to put 3V external voltage,or 5V tooken from LM7805(Lo)

08-27-2005, 09:29	#9 (permalink)
vipermat Junior Member Join Date: Sep 2004 Age: 38 Posts: 23 Member: 80949 Status: Offline Thanks Meter: 0	Thank for reply. You say that: for unlock GX15/GX25 i must have simple USB cable(unsoldering 4,5 and 8,9,10) for unlock GX30 i must have com cable. Correct I undestand?( My english is not good). Another Q: Can I use simple USB cable to normal comunicate( ogrinal sharp software or diferental) with GX15 or maybe GX30?

02-22-2006, 13:27	#11 (permalink)
crusher No Life Poster Join Date: Dec 2001 Location: [winscard.SCardTransmit] Posts: 1,835 Member: 8023 Status: Offline Thanks Meter: 13	you dont need unsolder 4 and 5, it can be used to unlock the phone as well. maybe you dont need to unsolder 8,9,10 but this is not tested!! but 4 and 5 connected WORKS TESTED for UNLOCK and FLASH in MOST cases.

02-22-2006, 14:00	#13 (permalink)
Platijet No Life Poster Join Date: Apr 2003 Location: Greece Age: 47 Posts: 3,358 Member: 26279 Status: Offline Thanks Meter: 274	check stickys threads about cables

02-22-2006, 15:27	#15 (permalink)
Platijet No Life Poster Join Date: Apr 2003 Location: Greece Age: 47 Posts: 3,358 Member: 26279 Status: Offline Thanks Meter: 274	my previus post was for all members.that i'm trying to say is that using flash USB cable(NEC 3G)you don't have autoignition(especialy user code on SPST).same case for GX30 usb/com cable.