Flashing R2**,t100, T108, N400, N500 Without Ext.power - GSM-Forum

KisaKot · 12-07-2002, 14:40

This PIN-OUT for flashing without Ext. power!!!
Used standart Rx-Tx cable.
I flashing R220, R210, T100, N400... 100% works.

http://kisakot.pisem.net/flashing.gif

Instruction:

1. Run Tool_Box-v4.0 and go to section "Environ Setting" and press "Autoconfig"
for Baud Rate = 115200.
2. Go to section "Downloader".
3. In section "Target Model" select model phone.
4. In section "Mode Selection" select "Binary File" and if need - "OGM-File".
5. In section "File Selection" open "Main flash" and if need "Second Flash".
6. In section "Option" select "Check Checksum".
7. Press "Start" and fast insert connector into phone. (Phone must be off).

!WARNING! Insert connector only after press "Start" !!!

If all OK - program say "Target Detected!!!" and run process update flash.

P.S. The battery should be charged minimum 30-40% !!!

.::AkhavanGSM::. · 03-31-2003, 13:01

Why i got checksum error?
but flashing done ok???

adv · 03-31-2003, 14:16

scheme not found on the provided link...
can someone post another link for this scheme?

regards

KisaKot · 03-31-2003, 20:15

http://mel.123shop.ru/flashing.gif

Elco · 03-31-2003, 20:50

Good work man

marmat · 10-24-2004, 21:42

I need scheme cable for flesh N500 (Toolbox 4.0 )
A300 not working ?

Maichel · 11-01-2004, 15:43

Hi U all I have Flashed N500 Frm My Twister Device And ITs Gone dead
And Then i have tried Another 1 So Dats Also gone Dead its Goes to 100% than shown me Red Line And Dead Plz Do me favour abut it Emm Really Not getting all thiz

Maichel · 11-01-2004, 15:50

Hi U all I have Flashed N500 Frm My Twister Device And ITs Gone dead
And Then i have tried Another 1 So Dats Also gone Dead its Goes to 100% than shown me Red Line And Dead Plz Do me favour abut it Emm Really Not getting all thiz

12-07-2002, 14:40	#1 (permalink)
KisaKot Freak Poster Join Date: Jun 2002 Location: Russia Age: 47 Posts: 212 Member: 13257 Status: Offline Thanks Meter: 1	Flashing R2,t100, T108, N400, N500 Without Ext.power** This PIN-OUT for flashing without Ext. power!!! Used standart Rx-Tx cable. I flashing R220, R210, T100, N400... 100% works. http://kisakot.pisem.net/flashing.gif Instruction: 1. Run Tool_Box-v4.0 and go to section "Environ Setting" and press "Autoconfig" for Baud Rate = 115200. 2. Go to section "Downloader". 3. In section "Target Model" select model phone. 4. In section "Mode Selection" select "Binary File" and if need - "OGM-File". 5. In section "File Selection" open "Main flash" and if need "Second Flash". 6. In section "Option" select "Check Checksum". 7. Press "Start" and fast insert connector into phone. (Phone must be off). !WARNING! Insert connector only after press "Start" !!! If all OK - program say "Target Detected!!!" and run process update flash. P.S. The battery should be charged minimum 30-40% !!! Last edited by KisaKot; 12-07-2002 at 15:06.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Modify K750 cable working without ext power.	Falck	SonyEricsson (USB-Smart)	81	08-16-2006 07:40
cable Sharp without ext power?	mighel	SonyEricsson (USB-Smart)	0	09-18-2005 22:49
t100-t108	h.man	SYSOL Platform	0	01-27-2004 20:46
T100 / T108	squidgy45	VLSI, Conexant, Skyworks and Old Models	4	09-01-2002 16:58
I need Z5 flashing cables with ext. power supply!	NUGSM	Main Sales Section	0	09-13-2001 11:08

03-31-2003, 13:01	#2 (permalink)
.::AkhavanGSM::. No Life Poster Join Date: Jun 2002 Location: Iran Age: 47 Posts: 1,082 Member: 12724 Status: Offline Thanks Meter: 30	Why i got checksum error? but flashing done ok???

03-31-2003, 14:16	#3 (permalink)
adv Freak Poster Join Date: Sep 2002 Location: somewhere... Posts: 419 Member: 15165 Status: Offline Thanks Meter: 0	scheme not found on the provided link... can someone post another link for this scheme? regards

03-31-2003, 20:15	#4 (permalink)
KisaKot Freak Poster Join Date: Jun 2002 Location: Russia Age: 47 Posts: 212 Member: 13257 Status: Offline Thanks Meter: 1	http://mel.123shop.ru/flashing.gif

03-31-2003, 20:50	#5 (permalink)
Elco No Life Poster Join Date: Dec 2002 Location: Romania Posts: 10,018 Member: 19254 Status: Offline Sonork: 100.72990 Thanks Meter: 25,395	Good work man

10-24-2004, 21:42	#6 (permalink)
marmat Junior Member Join Date: Dec 2003 Location: Poland Age: 56 Posts: 32 Member: 45689 Status: Offline Thanks Meter: 0	I need scheme cable for flesh N500 (Toolbox 4.0 ) A300 not working ?

11-01-2004, 15:43	#7 (permalink)
Maichel Insane Poster Join Date: Aug 2004 Location: Pakistan Age: 41 Posts: 79 Member: 79502 Status: Offline Thanks Meter: 6	Hi U all I have Flashed N500 Frm My Twister Device And ITs Gone dead And Then i have tried Another 1 So Dats Also gone Dead its Goes to 100% than shown me Red Line And Dead Plz Do me favour abut it Emm Really Not getting all thiz

11-01-2004, 15:50	#8 (permalink)
Maichel Insane Poster Join Date: Aug 2004 Location: Pakistan Age: 41 Posts: 79 Member: 79502 Status: Offline Thanks Meter: 6	Hi U all I have Flashed N500 Frm My Twister Device And ITs Gone dead And Then i have tried Another 1 So Dats Also gone Dead its Goes to 100% than shown me Red Line And Dead Plz Do me favour abut it Emm Really Not getting all thiz