All Samsung Cable into ONE CABLE!!! - GSM-Forum

karabey · 01-22-2005, 01:52

Hi Guys,

I am going to make only ONE Cable which will support all Samsung Phones - Siemens Phones - Nokia Phones and maybe later other Phones also. Its not so hard to do it but i need a little bit your help.

I am using to do this PS2 Connectors!! On the Serial side the PS2 Female and to other side PS2 Male.

I have looked on all Pinouts and i have got only one problem and that is the SERIAL CABLE.

As i have seen on BRUCE Pinouts is the schem for Serial like this:

9PIN Male

1- DCD = ???
2- RxD = RX
3- TxD = TX
4- DTR = ???
5- GND = GROUND
6- DSR = ???
7- RTS = Read **** ????
8- CLS = Clear **** ????
9- RI = ???

Now how can i know where i have to Connect "VPP", "VCC", "DATA IN", "DATA OUT".

I now on the Phone connectors where is MBUS,RX,TX and GROUND and i connected all of them. But it need the Connections like i have told above!

On the ****ing Serial Cable it has been only written the MBUS,RX,TX,GND next to the solderings but not VPP or others!

So please tell me what i can do????

Thanks and best regards
karabey

karabey · 01-22-2005, 02:26

OK i will ask it easier

The Pins 1 - 5 - 18 of A300 Flash Cable is VPP. Could someone tell me on which PIN of SERIAL is this connected??

bobjani2005 · 02-04-2005, 20:24

a500 sim unloking any bady halp me plz brit777_2002@yahoo.com

01-22-2005, 01:52	#1 (permalink)
karabey No Life Poster Join Date: Nov 2003 Age: 32 Posts: 977 Member: 45183 Status: Offline Thanks: 66 Thanked 462 Times in 113 Posts	All Samsung Cable into ONE CABLE!!! Hi Guys, I am going to make only ONE Cable which will support all Samsung Phones - Siemens Phones - Nokia Phones and maybe later other Phones also. Its not so hard to do it but i need a little bit your help. I am using to do this PS2 Connectors!! On the Serial side the PS2 Female and to other side PS2 Male. I have looked on all Pinouts and i have got only one problem and that is the SERIAL CABLE. As i have seen on BRUCE Pinouts is the schem for Serial like this: 9PIN Male 1- DCD = ??? 2- RxD = RX 3- TxD = TX 4- DTR = ??? 5- GND = GROUND 6- DSR = ??? 7- RTS = Read ** ???? 8- CLS = Clear ???? 9- RI = ??? Now how can i know where i have to Connect "VPP", "VCC", "DATA IN", "DATA OUT". I now on the Phone connectors where is MBUS,RX,TX and GROUND and i connected all of them. But it need the Connections like i have told above! On the **ing Serial Cable it has been only written the MBUS,RX,TX,GND next to the solderings but not VPP or others! So please tell me what i can do???? Thanks and best regards karabey

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
All samsung pst in one place	rajan nishchal	Various CDMA/TDMA Cell Phones	2	11-14-2009 17:28
how to convert SE data cable into flashing cable	hasanz	Sony Ericsson Hardware Repair Area	2	05-12-2008 05:09
all samsung unlock via one software	Moosani	Samsung Flashers, Software, Firmware.	20	10-08-2003 22:02

01-22-2005, 02:26	#2 (permalink)
karabey No Life Poster Join Date: Nov 2003 Age: 32 Posts: 977 Member: 45183 Status: Offline Thanks: 66 Thanked 462 Times in 113 Posts	OK i will ask it easier The Pins 1 - 5 - 18 of A300 Flash Cable is VPP. Could someone tell me on which PIN of SERIAL is this connected??

02-04-2005, 20:24	#3 (permalink)
bobjani2005 Freak Poster Join Date: Jan 2005 Posts: 291 Member: 108579 Status: Offline Thanks: 5 Thanked 3 Times in 3 Posts	a500 sim unloking any bady halp me plz brit777_2002@yahoo.com