|
|
|
| |||||||
| ARM9 BASED M62 / M62+ All MYxxx Like: MY C3-2, MY X1-2, MY Z-55, MY X2-2, MY C-4, MY Z-3, MY C2-2,
MY V-75, MY X3-2, MY X-7, MY V-65, MY C-1, MY X-1w, MY C-6, MY C-5w, MY C-2, MY
X-2, MY X-6, MY G5, MY X-3, MY X-5, MW X1, MY V-56, VS2, VS1, MY C5-2, MY X-8,
MY X-4, MY C4-2, MY V-55, MY X5-2, MY C-3b, MY C-3s,MY100, MY200, MY300X, MY400, MY V-85, MY V-76,
MY X6-2 etc Also SG321i, VS3 & MY-S7 (Smart Phone) |
 |
| | LinkBack | Thread Tools | Display Modes |
09-21-2004, 22:53
| #1 (permalink) |
| Freak Poster  Join Date: Sep 2003 Location: serbia Age: 30
Posts: 153
Member: 39065 Status: Offline Thanks: 0
Thanked 1 Time in 1 Post
| my v65 I have scr v12 and he work with sagem 9xx I tried with sagem my v65 and he stop at 33% and say bad connection Also tried scr 13 scr 11 but its same solutions to unlock? |
       |
|
09-23-2004, 00:25
| #6 (permalink) |
| Freak Poster Join Date: Sep 2003 Location: serbia Age: 30
Posts: 153
Member: 39065 Status: Offline Thanks: 0
Thanked 1 Time in 1 Post
| I KILL my atmega16 today I try to select all security and data bits in pony prog click write and.. My atmega16 after that in pony prog say device missing Is there solutons to revive chip or I lose 6 euro Sorry for bad english |
| |
|
09-27-2004, 19:39
| #8 (permalink) |
| Freak Poster Join Date: Sep 2003 Location: serbia Age: 30
Posts: 153
Member: 39065 Status: Offline Thanks: 0
Thanked 1 Time in 1 Post
| I dont understand,made scr with atmega16 work with sagem 922 but with myv65 error bad connection I look at testpoint but everything is ok upload schema and testpoints ,I dont understand what to do Also upgrade and repair with scr v14 from badunlocker but its the same bad connection any idea thanks c1 and c2= 27pf resistors are 100 ohm and crystal 3.68 db9.2=pin39(pa1) db9.3=pin40(pa0) db9.8=pin38(pa2) db9.9=pin29(pc7) |
| |
|
09-27-2004, 20:57
| #9 (permalink) |
| Freak Poster  Join Date: Oct 2003 Location: CONSTANTA Age: 29
Posts: 420
Member: 40747 Status: Offline Thanks: 0
Thanked 0 Times in 0 Posts
| Hello As Someone Before Me Said I Also Had One My 65 And Aslo Giving Bad Connection Untill I Soldered Wires From Testpoints To Test Jig And The Phone Was Detected And Unlocked. Good Luck I.T WORKED WITH CDR 14 POWER PHONE AND THEN WHEN SAIS SIM MISSING PRESSED READ CODES |
| |
|
09-27-2004, 21:42
| #10 (permalink) |
| Freak Poster Join Date: Sep 2003 Location: serbia Age: 30
Posts: 153
Member: 39065 Status: Offline Thanks: 0
Thanked 1 Time in 1 Post
| I solder many times but nothing,same bad connecting,also short my wire now wire is about 5 cm directly from jig to testpoint. is this testpoint on the picture for myv65 ok |
| |
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
