PANASONIC GD55 and ST55 UPDATE DOWNLOAD - GSM-Forum

**Networkunlock** · 10-02-2003, 21:56

Another fantastic update as promised by GRIFFIN TEAM.

DOWNLOAD HERE UPDATE FOR GD55 & ST55

INSTRUCTIONS

1)Power ON clip
2) Connect update cable
3) LOAD UPDATE FILE using update tool attached in zip file.
4) When you see 2 LED's blink at the same time. The clip is updated.
4) Run the program and enter IMEI and choose model. Click on GET CODES and you will see all the codes to UNLOCK your phone.
5) For PAN insert any foreign sim and enter codes.

This update is for all serial numbers.

All thanks go to Griffin Team and for all those impatients I can assure you GT have not been sleeping but have been working hard to ensure their customers are satisfied.
ENJOY this update for the moment and as always this is not the end ....

Regards

NADS

GRIFFIN SUPPORT TEAM.

GRIFFIN GTCL-01 CLIP SUPPORT PAGE

Always check here for updates and news.

fonefun · 10-02-2003, 22:17

Very good update work 100% on 2 gd55

all the best goes out to Griffin

www.fonefunshop.co.uk
[email protected]

stigor · 10-02-2003, 22:35

Now when i flash GTCL with new update, when press power
ON, firts both LEDs blink very fast, after that RED blink
few times, and on end green LED blink (ready for USE mode),
that is normal after new update?

And why when enter code i get info CANT SEND?
Clip is TURN ON, green LED not flashing, just light ON,
DATA CABLE is on COM1.

mobymaster · 10-02-2003, 22:56

@ Stigor

Power your clip up (not connected) the green LED should start to flash asif you were about to start an unlock.

Open the software

Connect the cable to the clip (note the red and green leds will now be flashing)

Press get codes, type in the IMEI and press OK

This will be displayed on the screen:

Calculating Using COM1... OK

Panasonic GD55 Imei:350000000000000

**00012*03530701#
**00013*76369749#
**00022*03130901#
**00023*76561749#
**00032*03831911#
**00033*71518749#
**00042*03359971#
**00043*75537949#
**00052*03538781#
**00053*78389749#

Hope this helps.

stigor · 10-02-2003, 23:01

Yes. TNX. And now, which code to enter to full unlock?
All of ten, or just one? Which code make full unlock, like
code 7 in DCT4 calc? Question is for GD55 and ST55.

all-gsm · 10-02-2003, 23:14

@ supper NICE

****Never say Never****

***all-gsm***

GSM Brothers · 10-03-2003, 05:39

verrry cooool update

Sandman · 10-03-2003, 06:30

another great work from griffin team...

thanks and best regards,

stigor · 10-03-2003, 06:34

Which code to enter for full unlock, only 0053 or all
of ten?

djparadi · 10-03-2003, 11:32

werry nice work!! THX griffin team?
Possiblel soon griffin box update (nokia)?????
djparadi

gsm-brest · 10-04-2003, 00:56

but for st55 sxematic???
were??
thanx

zmicier · 10-04-2003, 01:58

good news for all clip owners
and bad for all freebeggerz)))

zmicier · 10-04-2003, 02:01

Quote:

Originally posted by gsm-brest
but for st55 sxematic???
were??
thanx

4) Run the program and enter IMEI and choose model. Click on GET CODES and you will see all the codes to UNLOCK your phone.

you don't need a cable. only IMEI.

DonaldDuck69 · 10-05-2003, 16:36

Very good update

Thanks

t100 · 10-17-2003, 17:14

helpppppp. i power on seimens clip, but both green and red flash all the time, i think that only green should be working. when i load prog and enter imei for gd55, i get message can't send. anybody help please. thanks

10-02-2003, 21:56	#1 (permalink)
Networkunlock Product Manager Join Date: Mar 2002 Location: On the Edge Posts: 561 Member: 10347 Status: Offline Thanks Meter: 14	PANASONIC GD55 and ST55 UPDATE DOWNLOAD Another fantastic update as promised by GRIFFIN TEAM. DOWNLOAD HERE UPDATE FOR GD55 & ST55 INSTRUCTIONS 1)Power ON clip 2) Connect update cable 3) LOAD UPDATE FILE using update tool attached in zip file. 4) When you see 2 LED's blink at the same time. The clip is updated. 4) Run the program and enter IMEI and choose model. Click on GET CODES and you will see all the codes to UNLOCK your phone. 5) For PAN insert any foreign sim and enter codes. This update is for all serial numbers. All thanks go to Griffin Team and for all those impatients I can assure you GT have not been sleeping but have been working hard to ensure their customers are satisfied. ENJOY this update for the moment and as always this is not the end .... Regards NADS GRIFFIN SUPPORT TEAM. GRIFFIN GTCL-01 CLIP SUPPORT PAGE Always check here for updates and news. Last edited by Networkunlock; 10-02-2003 at 22:06.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Free Panasonic GD55 & Siemens ST55 Caclulater	KATOUE	Panasonic	61	08-04-2004 10:40
New DCT4 calc with Siemens ST55, CL55 and Panasonic GD55 support!!!	dluik	Nokia Multimedia	21	01-31-2004 22:25
I was reversing and creating tool for Siemens ST55 & Panasonic GD55 UNLOCK	sendel	Siemens Hardware Repair Area	20	01-13-2004 05:06
New DCT4 calc with Siemens ST55, CL55 and Panasonic GD55 support!!!	CyberGSM	Siemens-Benq RingTones and WallPapers	2	11-07-2003 08:58
New DCT4 calc with Siemens ST55, CL55 and Panasonic GD55 support!!!	CyberGSM	Panasonic	1	10-28-2003 14:48

10-02-2003, 22:17	#2 (permalink)
fonefun No Life Poster Join Date: Apr 2003 Location: Sheffield Posts: 709 Member: 26187 Status: Offline Sonork: 100:77458 Thanks Meter: 290	Very good update work 100% on 2 gd55 all the best goes out to Griffin www.fonefunshop.co.uk [email protected]

10-02-2003, 22:35	#3 (permalink)
stigor No Life Poster Join Date: Feb 2002 Location: Serbia Posts: 878 Member: 9165 Status: Offline Thanks Meter: 0	Now when i flash GTCL with new update, when press power ON, firts both LEDs blink very fast, after that RED blink few times, and on end green LED blink (ready for USE mode), that is normal after new update? And why when enter code i get info CANT SEND? Clip is TURN ON, green LED not flashing, just light ON, DATA CABLE is on COM1.

10-02-2003, 22:56	#4 (permalink)
mobymaster Freak Poster Join Date: Jul 2002 Location: Manchester, UK Posts: 259 Member: 13975 Status: Offline Thanks Meter: 7	@ Stigor Power your clip up (not connected) the green LED should start to flash asif you were about to start an unlock. Open the software Connect the cable to the clip (note the red and green leds will now be flashing) Press get codes, type in the IMEI and press OK This will be displayed on the screen: Calculating Using COM1... OK Panasonic GD55 Imei:350000000000000 *0001203530701# *0001376369749# *0002203130901# *0002376561749# *0003203831911# *0003371518749# *0004203359971# *0004375537949# *0005203538781# *0005378389749# Hope this helps.

10-02-2003, 23:01	#5 (permalink)
stigor No Life Poster Join Date: Feb 2002 Location: Serbia Posts: 878 Member: 9165 Status: Offline Thanks Meter: 0	Yes. TNX. And now, which code to enter to full unlock? All of ten, or just one? Which code make full unlock, like code 7 in DCT4 calc? Question is for GD55 and ST55.

10-02-2003, 23:14	#6 (permalink)
all-gsm Freak Poster Join Date: Apr 2002 Location: Romania Age: 56 Posts: 403 Member: 11347 Status: Offline Thanks Meter: 6	@ supper NICE **Never say Never all-gsm**

10-03-2003, 05:39	#7 (permalink)
GSM Brothers No Life Poster Join Date: Sep 2000 Location: Romania,Cluj Age: 49 Posts: 1,219 Member: 2203 Status: Offline Thanks Meter: 52	verrry cooool update

10-03-2003, 06:30	#8 (permalink)
Sandman No Life Poster Join Date: Nov 2001 Location: Never Land Posts: 924 Member: 7277 Status: Offline Sonork: 100.42158 Thanks Meter: 68	another great work from griffin team... thanks and best regards,

10-03-2003, 06:34	#9 (permalink)
stigor No Life Poster Join Date: Feb 2002 Location: Serbia Posts: 878 Member: 9165 Status: Offline Thanks Meter: 0	Which code to enter for full unlock, only 0053 or all of ten?

10-03-2003, 11:32	#10 (permalink)
djparadi Freak Poster Join Date: Apr 2001 Location: New-York,Rio,Tokyo! Age: 52 Posts: 227 Member: 4385 Status: Offline Thanks Meter: 1	werry nice work!! THX griffin team? Possiblel soon griffin box update (nokia)????? djparadi

10-04-2003, 00:56	#11 (permalink)
gsm-brest No Life Poster Join Date: Dec 2002 Location: Belarus Age: 45 Posts: 541 Member: 18813 Status: Offline Thanks Meter: 3	but for st55 sxematic??? were?? thanx

10-04-2003, 01:58	#12 (permalink)
zmicier Freak Poster Join Date: Oct 2001 Location: Minsk, Belarus Posts: 251 Member: 6937 Status: Offline Thanks Meter: 0	good news for all clip owners and bad for all freebeggerz)))

10-05-2003, 16:36	#14 (permalink)
DonaldDuck69 No Life Poster Join Date: Aug 2001 Location: Austria Posts: 841 Member: 5641 Status: Offline Thanks Meter: 72	Very good update Thanks

10-17-2003, 17:14	#15 (permalink)
t100 Insane Poster Join Date: Jan 2003 Age: 52 Posts: 99 Member: 19410 Status: Offline Thanks Meter: 1	helpppppp. i power on seimens clip, but both green and red flash all the time, i think that only green should be working. when i load prog and enter imei for gd55, i get message can't send. anybody help please. thanks