Problem with flashing Nokia 8910i... - GSM-Forum

king180579 · 06-26-2004, 14:37

I just received a new Matrix box and i tried to flash an Asian 8910i with the Europese flash packs.
I opened version 5.0.056 (Overloaded) program with the dos-fil (Over.bat)
I selected the variants and push Flash.
The phone is in local mode now but get the following message:

Flashing MCU (c:\program files\nokia\phoenix\products\nhm-4nx\nhm4nx5.250)
Enabling phone
Loading boot

And now... nothing happens... jsut loading boot... phone stays in but nothing happens. Somebody said i had to disconnect the phone immediately because it can die of that...
All 3 LED's are on the Matrix flash box are highlighted and the switch is on DCT4 (although that's unimportant since i have a new version of the box and the switch always has to stay at DCT4)

Does anybody knows the answer to my problem? Thx in advance!

king180579 · 06-26-2004, 15:55

Same with 6310i, i just tried to flash...

Flashing MCU (c:\program files\nokia\phoenix\products\npl-1\npl110_5.510)
Enabling phone

Just keeps hanging on Enabling phone... furthermore nothing happens..

king180579 · 06-26-2004, 16:01

Tried to flash 6310i again but with "Detect variant and set files before flashing" and got this message:

Flashing MCU (c:\program files\nokia\phoenix\products\npl-1\npl110_5.510)
Enabling phone
Loading boot
Wrong response. If you try to flash non Symbian phone, please set box switch to DCT3

Yeah...switch to DCT3... with my box switching to DCT3 is not possible because he can't find the Dongle..

John_Doe · 06-27-2004, 13:57

please open the box and check if PIN28 of Processor is disconnected(cutted). If not, then please do so and report here.

marcinw · 06-27-2004, 23:35

simple question for king: in config window there is checkbox for fast/slow flashing mode ("flash without 100% CPU usage..."). does problem happen in both selections of it ?

king180579 · 06-28-2004, 00:20

Quote:

Originally Posted by marcinw

simple question for king: in config window there is checkbox for fast/slow flashing mode ("flash without 100% CPU usage..."). does problem happen in both selections of it ?

I unmarked the box for 100% CPU usage but still the same..

king180579 · 06-28-2004, 00:23

Quote:

Originally Posted by John_Doe

please open the box and check if PIN28 of Processor is disconnected(cutted). If not, then please do so and report here.

Thx for reply.. i opened the box but..ermm.. where is pin28?

And if i find it.. can i just cut it without damaging the box?

An other question.. i just saw the box is version 22.08.2003.. is this the latest one?

davor · 06-28-2004, 13:18

Quote:

Originally Posted by king180579

Thx for reply.. i opened the box but..ermm.. where is pin28?

And if i find it.. can i just cut it without damaging the box?

An other question.. i just saw the box is version 22.08.2003.. is this the latest one?

looke here for pin28 location...

22082003 is latest HW...

king180579 · 06-28-2004, 16:01

Quote:

Originally Posted by davor

looke here for pin28 location...

22082003 is latest HW...

I cut pin 28 but still the same problem.
In fact the software will not go any further than saying "Enabling phone"
(Not even "Loading boot" anymore!

)

king180579 · 06-28-2004, 23:46

Somebody got a solution??

Mastah-GSi · 06-29-2004, 16:07

When flashing the switch always has to be set on DCT4.
When you want to use Logomanager or other programs you have to put the switch onto DCT3.

On what Operating System are you trying to flash?
I had the same problem on Win98se, but installing onto WinXP everything working 100%
You're sure that you use the latest flashpack update v3.09.002?

king180579 · 07-02-2004, 10:17

Quote:

Originally Posted by Mastah-GSi

When flashing the switch always has to be set on DCT4.
When you want to use Logomanager or other programs you have to put the switch onto DCT3.

On what Operating System are you trying to flash?
I had the same problem on Win98se, but installing onto WinXP everything working 100%
You're sure that you use the latest flashpack update v3.09.002?

I tried it both on Win98 as WinXP; with the latest flash pack but still don't work..
I CAN read phone info but i just can't flash...

king180579 · 07-07-2004, 10:51

Anyone???

STILL can't flash...

MiH · 07-08-2004, 07:34

Try change the paralell port mode to EPP or ECP in BIOS of your comp....

Leo140 · 07-20-2004, 07:12

contact retailer. good luck

06-26-2004, 14:37	#1 (permalink)
king180579 Junior Member Join Date: Jun 2004 Location: Outer Space Age: 44 Posts: 24 Member: 70370 Status: Offline Thanks Meter: 0	Problem with flashing Nokia 8910i... I just received a new Matrix box and i tried to flash an Asian 8910i with the Europese flash packs. I opened version 5.0.056 (Overloaded) program with the dos-fil (Over.bat) I selected the variants and push Flash. The phone is in local mode now but get the following message: Flashing MCU (c:\program files\nokia\phoenix\products\nhm-4nx\nhm4nx5.250) Enabling phone Loading boot And now... nothing happens... jsut loading boot... phone stays in but nothing happens. Somebody said i had to disconnect the phone immediately because it can die of that... All 3 LED's are on the Matrix flash box are highlighted and the switch is on DCT4 (although that's unimportant since i have a new version of the box and the switch always has to stay at DCT4) Does anybody knows the answer to my problem? Thx in advance!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problems with flashing Nokia 2600 v4.42	lexwon	Twisterflasher	12	11-03-2005 00:14
Problem with Flashing Nokia 3200 & 6100	Abdulgsm	Twisterflasher	4	08-18-2005 12:53
Problem with flashing NOKIA 9210i !!!	gsm_shogun	UFS2 + UFS3-Tornadoflasher	0	05-18-2005 18:45
Big Problem with flashing nokia 3650 with griffin	Slavonac	Griffin	11	06-12-2004 20:57
Problems with flashing Nokia 3310	Unlock_Service	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	06-19-2003 15:57

06-26-2004, 15:55	#2 (permalink)
king180579 Junior Member Join Date: Jun 2004 Location: Outer Space Age: 44 Posts: 24 Member: 70370 Status: Offline Thanks Meter: 0	Same with 6310i, i just tried to flash... Flashing MCU (c:\program files\nokia\phoenix\products\npl-1\npl110_5.510) Enabling phone Just keeps hanging on Enabling phone... furthermore nothing happens..

06-26-2004, 16:01	#3 (permalink)
king180579 Junior Member Join Date: Jun 2004 Location: Outer Space Age: 44 Posts: 24 Member: 70370 Status: Offline Thanks Meter: 0	Tried to flash 6310i again but with "Detect variant and set files before flashing" and got this message: Flashing MCU (c:\program files\nokia\phoenix\products\npl-1\npl110_5.510) Enabling phone Loading boot Wrong response. If you try to flash non Symbian phone, please set box switch to DCT3 Yeah...switch to DCT3... with my box switching to DCT3 is not possible because he can't find the Dongle..

06-27-2004, 13:57	#4 (permalink)
John_Doe No Life Poster Join Date: Aug 2000 Location: anywhere Posts: 596 Member: 1879 Status: Offline Sonork: 100.28016 Thanks Meter: 941	please open the box and check if PIN28 of Processor is disconnected(cutted). If not, then please do so and report here.

06-27-2004, 23:35	#5 (permalink)
marcinw Insane Poster Join Date: Apr 2002 Posts: 86 Member: 11251 Status: Offline Thanks Meter: 0	simple question for king: in config window there is checkbox for fast/slow flashing mode ("flash without 100% CPU usage..."). does problem happen in both selections of it ?

06-28-2004, 23:46	#10 (permalink)
king180579 Junior Member Join Date: Jun 2004 Location: Outer Space Age: 44 Posts: 24 Member: 70370 Status: Offline Thanks Meter: 0	Somebody got a solution??

06-29-2004, 16:07	#11 (permalink)
Mastah-GSi Freak Poster Join Date: Jul 2003 Location: Enschede, Netherlands Age: 41 Posts: 415 Member: 34652 Status: Offline Thanks Meter: 5	When flashing the switch always has to be set on DCT4. When you want to use Logomanager or other programs you have to put the switch onto DCT3. On what Operating System are you trying to flash? I had the same problem on Win98se, but installing onto WinXP everything working 100% You're sure that you use the latest flashpack update v3.09.002?

07-07-2004, 10:51	#13 (permalink)
king180579 Junior Member Join Date: Jun 2004 Location: Outer Space Age: 44 Posts: 24 Member: 70370 Status: Offline Thanks Meter: 0	Anyone??? STILL can't flash...

07-08-2004, 07:34	#14 (permalink)
MiH Freak Poster Join Date: Dec 2002 Location: slovakia Age: 48 Posts: 259 Member: 18876 Status: Offline Thanks Meter: 27	Try change the paralell port mode to EPP or ECP in BIOS of your comp....

07-20-2004, 07:12	#15 (permalink)
Leo140 No Life Poster Join Date: Nov 2003 Age: 46 Posts: 823 Member: 43076 Status: Offline Thanks Meter: 10	contact retailer. good luck