6230i i erased the whole thing. - GSM-Forum

davoldv · 01-28-2007, 20:44

i am trying to bring back to life a dead 6230i so i decided to erase the whole thing then it said ajust start address then adjust end address,i just clicked ok and ok thn it erashed but now when flashing the mcu and ppm it say done but fone will still not work,wat should the start and end address be for a nokia 6230i.

regards

cooleyes · 01-28-2007, 22:02

if phone is not switching on after flashing it means there is Hardware Problem in Phone .
Erase is fixed by flashing Mcu Ppm and then writing PM and Product Profile

cell2cell · 01-29-2007, 18:52

what hard wear problem may led to this l have the same with my phone it is flashing well but will not power on it is also not charging the battery

davoldv · 01-29-2007, 19:02

same for me no charger,wat numbers should i put in to erashe start and end

cooleyes · 01-29-2007, 21:34

If Phone is not in on then how can it repond to charger

Check if any area is damage with liqid try to reheat flashes it may be drysold

Quote:

Originally Posted by cell2cell

what hard wear problem may led to this l have the same with my phone it is flashing well but will not power on it is also not charging the battery

davoldv · 01-29-2007, 22:08

wat numbers should i put in to erase the whole flash>> start and end

cell2cell · 02-02-2007, 22:09

l have heated the phone now it is powering on and then after 10 seconds off and flashers but l only have a white display could this now be softwear it is the older vision E l am going to try and flash with vision 3.7 hope it works. cooleyes the phone started the problem from a fall to the ground.

davoldv · 02-03-2007, 14:07

when u say heat the phone,what do u use to heat.

please help as mine still has the problem.

cell2cell · 02-03-2007, 19:10

l used hot air from a hot air gun and after flashing it the phone now stays on but only white screen any help out there.

cooleyes · 02-04-2007, 14:55

now u may try to flash the phone again u can try both E or M file to flash .

Quote:

Originally Posted by cell2cell

l have heated the phone now it is powering on and then after 10 seconds off and flashers but l only have a white display could this now be softwear it is the older vision E l am going to try and flash with vision 3.7 hope it works. cooleyes the phone started the problem from a fall to the ground.

cooleyes · 02-04-2007, 15:00

if u press the keypad button can u hear any beep ?
Have u checked to try any sim in phone ?
Have u tried the check any display ?

if u used software chk info what does it say ?
does during flashing /Test or Local info on Screen Appears

Quote:

Originally Posted by cell2cell

l used hot air from a hot air gun and after flashing it the phone now stays on but only white screen any help out there.

01-28-2007, 20:44	#1 (permalink)
davoldv Major Poster Join Date: Jan 2007 Posts: 47 Member: 437781 Status: Offline Thanks Meter: 0	6230i i erased the whole thing. i am trying to bring back to life a dead 6230i so i decided to erase the whole thing then it said ajust start address then adjust end address,i just clicked ok and ok thn it erashed but now when flashing the mcu and ppm it say done but fone will still not work,wat should the start and end address be for a nokia 6230i. regards

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
5130x completly dead after erase MXKEY whole erese	aukonline	MXKEY Nokia Flasher and Unlocker (by Alim Hape)	22	10-18-2011 07:07
The Whole Body Training Exercises of the Liang-Style Eight Diagrams Palm (?????-?????	IPMART	ipmart WebShop	0	03-10-2010 10:20
The Whole Body Training Exercises of the Liang-Style Eight Diagrams Palm (?????-?????	IPMART	ipmart WebShop	0	03-10-2010 10:20
need nokia 7610 camera parts and the whole body(base)	markLEE	Hardware Repair Item Wanted	0	05-27-2005 17:57
Is one selling nokia 3410 screen (lcd) not the whole lcd board	cameraman	Sell ur Old and Used Stuff	0	09-03-2004 10:38

01-28-2007, 22:02	#2 (permalink)
cooleyes No Life Poster Join Date: Apr 2003 Posts: 533 Member: 26066 Status: Offline Sonork: cooleyes Thanks Meter: 128	if phone is not switching on after flashing it means there is Hardware Problem in Phone . Erase is fixed by flashing Mcu Ppm and then writing PM and Product Profile

01-29-2007, 18:52	#3 (permalink)
cell2cell Freak Poster Join Date: Jun 2006 Posts: 264 Member: 299902 Status: Offline Thanks Meter: 20	what hard wear problem may led to this l have the same with my phone it is flashing well but will not power on it is also not charging the battery

01-29-2007, 19:02	#4 (permalink)
davoldv Major Poster Join Date: Jan 2007 Posts: 47 Member: 437781 Status: Offline Thanks Meter: 0	same for me no charger,wat numbers should i put in to erashe start and end

01-29-2007, 22:08	#6 (permalink)
davoldv Major Poster Join Date: Jan 2007 Posts: 47 Member: 437781 Status: Offline Thanks Meter: 0	wat numbers should i put in to erase the whole flash>> start and end

02-02-2007, 22:09	#7 (permalink)
cell2cell Freak Poster Join Date: Jun 2006 Posts: 264 Member: 299902 Status: Offline Thanks Meter: 20	l have heated the phone now it is powering on and then after 10 seconds off and flashers but l only have a white display could this now be softwear it is the older vision E l am going to try and flash with vision 3.7 hope it works. cooleyes the phone started the problem from a fall to the ground.

02-03-2007, 14:07	#8 (permalink)
davoldv Major Poster Join Date: Jan 2007 Posts: 47 Member: 437781 Status: Offline Thanks Meter: 0	when u say heat the phone,what do u use to heat. please help as mine still has the problem.

02-03-2007, 19:10	#9 (permalink)
cell2cell Freak Poster Join Date: Jun 2006 Posts: 264 Member: 299902 Status: Offline Thanks Meter: 20	l used hot air from a hot air gun and after flashing it the phone now stays on but only white screen any help out there.