n620 call problem ? - GSM-Forum

eng.hamdow · 10-30-2004, 15:04

i have samsung n620 , cannot make call " call failed "
thanks 4 all

daanish · 11-02-2004, 04:04

It's a hardware problem you have to replace the pa,some times if you remove Pa and clean both the pa and pcb with good thiner or ctc and replace the same pa it works but for some time only like for few days,it's better if you replace the pa
br Daanish

Imran_Khatri · 11-02-2004, 06:34

Nope, Just hot the EEPROM, Or reset EEPROM By 0x2767, 100% working.

WBR
Imran Khatri

mohammad2004 · 11-05-2004, 00:42

1-full eprom and flash org by ust pro

2-replace or change the pa or swich an -connector sky an check

3-replace or change e2prom ic 100% ok

najafi · 11-05-2004, 01:04

hi:you have problem pfo sand

nobal1976 · 11-07-2004, 17:40

mostly just cleen pcb with ctc your set will ok

10-30-2004, 15:04	#1 (permalink)
eng.hamdow Freak Poster Join Date: Oct 2004 Age: 54 Posts: 165 Member: 84648 Status: Offline Thanks Meter: 3	n620 call problem ? i have samsung n620 , cannot make call " call failed " thanks 4 all

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
n620 call faild	kanwal	Samsung Hardware Repair	2	07-05-2007 03:51
N620 call ended	santosh_dts	Samsung Hardware Repair	2	03-11-2005 09:31
N620 - Call Failed	webmoly	Samsung Hardware Repair	1	06-22-2004 20:02
N620 Battery problem	T2G	VLSI, Conexant, Skyworks and Old Models	0	06-11-2003 17:46
n620 strange problem	Siemens man	VLSI, Conexant, Skyworks and Old Models	0	04-23-2003 21:18

11-02-2004, 04:04	#2 (permalink)
daanish Freak Poster Join Date: Aug 2004 Location: The great pakistan Posts: 384 Member: 79823 Status: Offline Thanks Meter: 26	It's a hardware problem you have to replace the pa,some times if you remove Pa and clean both the pa and pcb with good thiner or ctc and replace the same pa it works but for some time only like for few days,it's better if you replace the pa br Daanish

11-02-2004, 06:34	#3 (permalink)
Imran_Khatri No Life Poster Join Date: Mar 2004 Location: Pakistan Age: 42 Posts: 1,416 Member: 56561 Status: Offline Sonork: 100.114006 Thanks Meter: 41	Nope, Just hot the EEPROM, Or reset EEPROM By 0x2767, 100% working. WBR Imran Khatri

11-05-2004, 00:42	#4 (permalink)
mohammad2004 No Life Poster Join Date: Jul 2004 Age: 38 Posts: 641 Member: 71144 Status: Offline Thanks Meter: 12	1-full eprom and flash org by ust pro 2-replace or change the pa or swich an -connector sky an check 3-replace or change e2prom ic 100% ok

11-05-2004, 01:04	#5 (permalink)
najafi Crazy Poster Join Date: Oct 2004 Location: www.ir-gsm.co Age: 40 Posts: 55 Member: 87996 Status: Offline Thanks Meter: 0	hi:you have problem pfo sand

11-07-2004, 17:40	#6 (permalink)
nobal1976 No Life Poster Join Date: Jul 2004 Location: Gujranwala Pakistan Age: 48 Posts: 758 Member: 71190 Status: Offline Sonork: 100.1580485 Thanks Meter: 87	mostly just cleen pcb with ctc your set will ok