T100 White Screen (Again) - GSM-Forum

clivea · 12-19-2004, 22:54

Hi Sorry about this old problem but I am relatively new to this game.
All I have done is change the cover on the T100 and alas a white screen.
Have replaced the ribbon cable as someone suggested, please note that I took about an hour for this and was extremely careful but it did not cure it. Can anybody give me a definite answer to fix this annoying problem.

Many thanks for your replies in advance.

Clive

uqbah · 12-20-2004, 18:59

ur problem is 100 % of ur lcd.....
while changing the case u got damage ur lcd ..
just closley watch the lcd u will find ur mistake.
no need to waste ur time just change the lcd.
no other solution exist

cellularry · 12-20-2004, 19:14

it's your flex cable. it could be the one you changed before not good or not fixed well. try it again before paying for LCD

clivea · 12-20-2004, 20:58

Have already replace ribbon cable twice now, still have white screen.

clivea · 12-22-2004, 20:39

Ok then, can anyone tell me where to look on the screen for possible damage, as have looked but cant find anything, so please can anyone help??

uqbah · 12-23-2004, 19:27

just carefully look at the corners of the lcd a very small breaking or damage....
there will be the a line or cut .
if could not find then u must check ur falted lcd on the working strip or on another phone which can help u to solve ur problem

ashrafha · 12-24-2004, 17:24

before changing the lcd try to clean the area where the cable is connected to the board and the cable connection too!!! it will save your prob.

clivea · 12-24-2004, 23:19

Thanks for the messages, I'll give them a go.

Merry christmas all.

mohammad2004 · 01-10-2005, 17:45

1-test the full flat and lcd

2-replce the flat cable

12-19-2004, 22:54	#1 (permalink)
clivea Junior Member Join Date: Dec 2004 Age: 50 Posts: 6 Member: 99124 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	T100 White Screen (Again) Hi Sorry about this old problem but I am relatively new to this game. All I have done is change the cover on the T100 and alas a white screen. Have replaced the ribbon cable as someone suggested, please note that I took about an hour for this and was extremely careful but it did not cure it. Can anybody give me a definite answer to fix this annoying problem. Many thanks for your replies in advance. Clive

12-20-2004, 18:59	#2 (permalink)
uqbah No Life Poster Join Date: Aug 2004 Location: MicroControllers:: Age: 32 Posts: 1,657 Member: 78619 Status: Offline Thanks: 251 Thanked 295 Times in 104 Posts	not flex cable ur problem is 100 % of ur lcd..... while changing the case u got damage ur lcd .. just closley watch the lcd u will find ur mistake. no need to waste ur time just change the lcd. no other solution exist

12-23-2004, 19:27	#6 (permalink)
uqbah No Life Poster Join Date: Aug 2004 Location: MicroControllers:: Age: 32 Posts: 1,657 Member: 78619 Status: Offline Thanks: 251 Thanked 295 Times in 104 Posts	dont woory just carefully look at the corners of the lcd a very small breaking or damage.... there will be the a line or cut . if could not find then u must check ur falted lcd on the working strip or on another phone which can help u to solve ur problem

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
5130 white screen when play video	fakhraei2000	Nokia Hardware & Hardware-Repair Area	13	11-15-2010 03:54
T100 white screen	millpc	VLSI, Conexant, Skyworks and Old Models	13	05-30-2004 14:00
t100 white screen	to-dick	VLSI, Conexant, Skyworks and Old Models	2	01-22-2004 22:46
T100 White Screen	MindPower	VLSI, Conexant, Skyworks and Old Models	18	08-08-2003 22:39
T100 white screen	mickeyblueeyes	VLSI, Conexant, Skyworks and Old Models	4	03-13-2003 19:12

12-20-2004, 19:14	#3 (permalink)
cellularry No Life Poster Join Date: Oct 2003 Location: Lebanon / Nigeria Age: 41 Posts: 1,091 Member: 42276 Status: Offline Thanks: 30 Thanked 46 Times in 30 Posts	it's your flex cable. it could be the one you changed before not good or not fixed well. try it again before paying for LCD

12-20-2004, 20:58	#4 (permalink)
clivea Junior Member Join Date: Dec 2004 Age: 50 Posts: 6 Member: 99124 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Have already replace ribbon cable twice now, still have white screen.

12-22-2004, 20:39	#5 (permalink)
clivea Junior Member Join Date: Dec 2004 Age: 50 Posts: 6 Member: 99124 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Ok then, can anyone tell me where to look on the screen for possible damage, as have looked but cant find anything, so please can anyone help??

12-24-2004, 17:24	#7 (permalink)
ashrafha Junior Member Join Date: Dec 2004 Age: 33 Posts: 10 Member: 100407 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	before changing the lcd try to clean the area where the cable is connected to the board and the cable connection too!!! it will save your prob.

12-24-2004, 23:19	#8 (permalink)
clivea Junior Member Join Date: Dec 2004 Age: 50 Posts: 6 Member: 99124 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Thanks for the messages, I'll give them a go. Merry christmas all.

01-10-2005, 17:45	#9 (permalink)
mohammad2004 No Life Poster Join Date: Jul 2004 Age: 27 Posts: 642 Member: 71144 Status: Offline Thanks: 0 Thanked 10 Times in 7 Posts	1-test the full flat and lcd 2-replce the flat cable