p800 no network - GSM-Forum

Lonegunman · 09-12-2004, 18:58

As above got a p800 showing no network stright away, now I guess this is due to the fact that the car airel part has been ripped off, any way to repair this or by pass it? (with out getting a new part) also I can't get ufs to read the phone just keep's going to charge any way round that as well?

Tbaba · 09-12-2004, 19:26

just short two points where the aerial used to be. the connector is made up of 4 points. Each pair of these points is short to the second. What i mean is, u av 4 points with 2 points shorted together but isolated from the other two points which are also shorted. Now that the connector is no more there. U can get a signal by putting a jumper wire (or shorting) the point going to the PA to it continuous pair (assuming the connector was there. I hope you understand. Ill try to take a cut out from the service manual and post here. good luck

Lonegunman · 09-12-2004, 19:51

I get the bit about shorting out the pairs, but a jumper to the PA that bit has lost me, right off to short some points out.

Many thanks

Also if you need to mail big stuff send it to here

Tbaba · 09-12-2004, 20:12

u dont reaslly need a jumper to the PA. just join the two points (that's just 1 of the initial pairs i was talking about b4) that have been left open due to the missing ext aerial connector. The second pair of points u could still leave open (they dont matter). What matters is the pair of points linking to the PA. Good luck!

Lonegunman · 09-12-2004, 20:50

I have 4 points 2 big one and 2 little ones, do I join the 2 big ones together or the 2 small ones or 1 big and 1 small?

Tbaba · 09-12-2004, 20:55

Very good! i like people that catch on fasssst. Just join the two small ones and voila... network... Good luck!

Lonegunman · 09-12-2004, 20:59

Many thanks, I know it was a simple trail and error but I had tried a few ways and was not getting anywere, right off to try and see if I can get this sorted.

TONYTONY · 09-14-2004, 09:00

Does anyone else have any other soultion for P800 software problem where external antenna is ok??

thanks
tonytony

09-12-2004, 18:58	#1 (permalink)
Lonegunman No Life Poster Join Date: Dec 2001 Location: London Age: 49 Posts: 792 Member: 7939 Status: Offline Thanks Meter: 2	p800 no network As above got a p800 showing no network stright away, now I guess this is due to the fact that the car airel part has been ripped off, any way to repair this or by pass it? (with out getting a new part) also I can't get ufs to read the phone just keep's going to charge any way round that as well?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
p800 no network	Number-One	Cruiser Suite	3	09-27-2005 06:13
P800 no network	amuroray	Sony Ericsson Hardware Repair	4	09-16-2004 16:24
P800 No Ringtones And No Games After Master Reset	magnet	Sony Ericsson	5	09-06-2004 17:16
P800 no network !!	Alwed	Sony Ericsson Hardware Repair	3	05-27-2004 10:28
P800 no display no light pls help???	proxy_gsm	Sony Ericsson	2	01-12-2004 19:46

09-12-2004, 19:26	#2 (permalink)
Tbaba No Life Poster Join Date: Feb 2003 Posts: 635 Member: 22208 Status: Offline Thanks Meter: 9	just short two points where the aerial used to be. the connector is made up of 4 points. Each pair of these points is short to the second. What i mean is, u av 4 points with 2 points shorted together but isolated from the other two points which are also shorted. Now that the connector is no more there. U can get a signal by putting a jumper wire (or shorting) the point going to the PA to it continuous pair (assuming the connector was there. I hope you understand. Ill try to take a cut out from the service manual and post here. good luck

09-12-2004, 19:51	#3 (permalink)
Lonegunman No Life Poster Join Date: Dec 2001 Location: London Age: 49 Posts: 792 Member: 7939 Status: Offline Thanks Meter: 2	I get the bit about shorting out the pairs, but a jumper to the PA that bit has lost me, right off to short some points out. Many thanks Also if you need to mail big stuff send it to here

09-12-2004, 20:12	#4 (permalink)
Tbaba No Life Poster Join Date: Feb 2003 Posts: 635 Member: 22208 Status: Offline Thanks Meter: 9	u dont reaslly need a jumper to the PA. just join the two points (that's just 1 of the initial pairs i was talking about b4) that have been left open due to the missing ext aerial connector. The second pair of points u could still leave open (they dont matter). What matters is the pair of points linking to the PA. Good luck!

09-12-2004, 20:50	#5 (permalink)
Lonegunman No Life Poster Join Date: Dec 2001 Location: London Age: 49 Posts: 792 Member: 7939 Status: Offline Thanks Meter: 2	I have 4 points 2 big one and 2 little ones, do I join the 2 big ones together or the 2 small ones or 1 big and 1 small?

09-12-2004, 20:55	#6 (permalink)
Tbaba No Life Poster Join Date: Feb 2003 Posts: 635 Member: 22208 Status: Offline Thanks Meter: 9	Very good! i like people that catch on fasssst. Just join the two small ones and voila... network... Good luck!

09-12-2004, 20:59	#7 (permalink)
Lonegunman No Life Poster Join Date: Dec 2001 Location: London Age: 49 Posts: 792 Member: 7939 Status: Offline Thanks Meter: 2	Many thanks, I know it was a simple trail and error but I had tried a few ways and was not getting anywere, right off to try and see if I can get this sorted.

09-14-2004, 09:00	#8 (permalink)
TONYTONY No Life Poster Join Date: Jul 2003 Location: BahaMAS Age: 40 Posts: 557 Member: 35975 Status: Offline Thanks Meter: 19	Does anyone else have any other soultion for P800 software problem where external antenna is ok?? thanks tonytony