T630 dead after flash? - GSM-Forum

XStoneX · 02-06-2005, 10:00

I flashed my T630 yesterday (wanted to do an update from R4E002 to R7A011) with Terminator Dongle and DIV LPT 5.0.

On the ARM Modem update the Flasher wrote an error code:

Error 3608
==========
Description:

ERROR 3608 means ARM flash chip failed to erase (bulk erase command issued, but flash not blank). It does it at 1% as on ARM chip, it does not use the progressive erase-write cycles, uses erasing the whole chip (this is the first percent), then starts to write only if the chip is empty (e.g. contents in the given range is of 0xFFs).

This can be caused by badly soldered or damaged flash chip, dirty phone connectors, bad connections, but also because of your PC being too fast (hate stable and accurate delay values, eh?), thus it would advance to flash blank check/write before the chip can actually finish the operation.

- Might be a faulty or fried ARM chip inside the phone

- Might be a faulty cable

- Might be a faulty dongle

Probable solution:

Try correcting the above mentioned issues that could cause this.

I retried to flash, but the phone does not power up. Also I tried to power the phone on by myself - no way. It's dead.

Can I put it into trash now? PLZ help!!!

THX,

XStoneX

cellularry · 02-10-2005, 21:31

No worry, it's not a big problem.
Myself i have DIV and Tornado and it happened with me several times that ARM flash stop at 1% while using DIV and phone goes dead.
So i will use tornado to flash it and phone will work normally 100%.

In my openion any phone that will die with software will come on again with software. There is nothing to fear off.

IgorY · 03-03-2005, 22:23

Sorry, where can I find flashfile for T630 R7A011 EMEA1?

PhonePlus · 03-03-2005, 22:41

on ur support area ... if u got TOrnado or DIV

IgorY · 03-04-2005, 19:21

I am use UFS3 and I can`t find it on support site...
Who can help me?

XStoneX · 03-06-2005, 17:50

I've downloaded the files at www.gorden.de - but you have to donate gorden to download the files.

@ cellularry - I've no tornado. What else can I do? Is there a possibility to repair the mobile by DIV?

Thx,

XStoneX

02-06-2005, 10:00	#1 (permalink)
XStoneX Junior Member Join Date: Jan 2004 Location: Austria Age: 35 Posts: 13 Member: 51567 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	T630 dead after flash? I flashed my T630 yesterday (wanted to do an update from R4E002 to R7A011) with Terminator Dongle and DIV LPT 5.0. On the ARM Modem update the Flasher wrote an error code: Error 3608 ========== Description: ERROR 3608 means ARM flash chip failed to erase (bulk erase command issued, but flash not blank). It does it at 1% as on ARM chip, it does not use the progressive erase-write cycles, uses erasing the whole chip (this is the first percent), then starts to write only if the chip is empty (e.g. contents in the given range is of 0xFFs). This can be caused by badly soldered or damaged flash chip, dirty phone connectors, bad connections, but also because of your PC being too fast (hate stable and accurate delay values, eh?), thus it would advance to flash blank check/write before the chip can actually finish the operation. - Might be a faulty or fried ARM chip inside the phone - Might be a faulty cable - Might be a faulty dongle Probable solution: Try correcting the above mentioned issues that could cause this. I retried to flash, but the phone does not power up. Also I tried to power the phone on by myself - no way. It's dead. Can I put it into trash now? PLZ help!!! THX, XStoneX

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
T630 Dead after Flash FS !!!	ti_zana	Cruiser Suite	1	11-18-2006 20:04
T630 dead after flash GDSF	erogsm	Sony Ericsson	8	06-14-2005 23:48
t630 dead after removing RSA	GSMATRIX0130	Sony Ericsson	17	03-01-2005 01:24
T630 dead after RSA remove	xelo	Sony Ericsson	14	10-07-2004 14:41
T630 DEAD after flash	connect01	Sony Ericsson Hardware Repair Area	0	05-11-2004 16:33

02-10-2005, 21:31	#2 (permalink)
cellularry No Life Poster Join Date: Oct 2003 Location: Lebanon / Nigeria Age: 41 Posts: 1,091 Member: 42276 Status: Offline Thanks: 30 Thanked 46 Times in 30 Posts	No worry, it's not a big problem. Myself i have DIV and Tornado and it happened with me several times that ARM flash stop at 1% while using DIV and phone goes dead. So i will use tornado to flash it and phone will work normally 100%. In my openion any phone that will die with software will come on again with software. There is nothing to fear off.

03-03-2005, 22:23	#3 (permalink)
IgorY Junior Member Join Date: Jan 2003 Location: BY Age: 40 Posts: 29 Member: 19928 Status: Offline Thanks: 1 Thanked 3 Times in 1 Post	Sorry, where can I find flashfile for T630 R7A011 EMEA1?

03-03-2005, 22:41	#4 (permalink)
PhonePlus Freak Poster Join Date: Jul 2004 Location: Sousse - Tunisia Posts: 474 Member: 71620 Status: Offline Thanks: 1 Thanked 8 Times in 6 Posts	on ur support area ... if u got TOrnado or DIV

03-04-2005, 19:21	#5 (permalink)
IgorY Junior Member Join Date: Jan 2003 Location: BY Age: 40 Posts: 29 Member: 19928 Status: Offline Thanks: 1 Thanked 3 Times in 1 Post	I am use UFS3 and I can`t find it on support site... Who can help me?

03-06-2005, 17:50	#6 (permalink)
XStoneX Junior Member Join Date: Jan 2004 Location: Austria Age: 35 Posts: 13 Member: 51567 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	I've downloaded the files at www.gorden.de - but you have to donate gorden to download the files. @ cellularry - I've no tornado. What else can I do? Is there a possibility to repair the mobile by DIV? Thx, XStoneX