l7 no display on lcd after unlock

[mobilelink44]

hi folks i unlocked an l7 the unlock was successful but my lcd showing no display now

my customer going mental any ideas

[needi]

So what exactly you did to make ur phone and customer mental.

[UHK]

solution for you buy new fone from me
i have for sell
or send me if ur in uk

by the way did u solder tp or just connect with pin or niddle
beware all motrola connected lcd during unlock or solder specially comon problem in v3x

[ExTrEmE99]

Hmm did you take out all the connectors when u unlocked the L7? Ive done 2 and no problems. Make sure if the LCD flex cable is on correctly connected to the main board and does any LEDs turn on?

[papis thiam]

hi.
i need a motorola l7 fullflash

[kingmobilephone]

Originally Posted by mobilelink44

hi folks i unlocked an l7 the unlock was successful but my lcd showing no display now

my customer going mental any ideas

I think it's a hardware damage while removing the metal shield

cos I also had a L6 here (no display first , then next time on, the display comes back and work normal for 5 mins ....and then display off...and now, no display)... it's obviously my fault while cutting the shield

anyway, just went to carphonewarehouse and bought a new L6 for customer (bad day, but good lesson)

[ExTrEmE99]

Hmm i dont get what happened. How did you remove the shield? drilling or cutting?
Kingmobilephone: What is your method of removing the shield? cutting with razor or drilling?

[mobilelink44]

i used a fresh razor to cut shield it is harder on l7 than it is on l6. i dnt think i damaged anything the unlock went thru fine too where is the cheapest place to aquire another handset on orange or t mobile??

[kingmobilephone]

Originally Posted by ExTrEmE99

Hmm i dont get what happened. How did you remove the shield? drilling or cutting?
Kingmobilephone: What is your method of removing the shield? cutting with razor or drilling?

My colleagus used the razor for doing that which she has done ten of them before .....

btw, I bought the new L6 from carphonewarehouse - orange
£79.99 included £10 credit (and it's unlocked)...so I don't need to cut the shield again

[Kola2001]

i think you will find that it is not your lcd as if u put phone in test mode (hold down * + # and power on) the display will power up properly.
sadly i dont still know a solution for this problem, i am waiting for a flash file from victor on mss forum, hopefully this would solve(fingers crossed).
phone died using SC, as you said unlocked succesfully but phone is just dead, keypad lights up but no screen.
I have already replaced phone for customer but would want this working as it is brand new, cheapest one would be on O2 for £129.99 if you needed to replace btw but it is locked and you will need to unlock.
It is a strange problem as i have unlocked 5 other l7 after that using SC and all were successful. Strange!!
hope this helps.

[ExTrEmE99]

Hmm i still dont get what wrong if its successful. I did one and i have someone sending me one to unlock i hope i dont get a problems with it too. Ive unlocked 4 testpoint phones and out them 1 "died" the ROKR E1 it says "call failed" it was successful too. Wierd SC needs to find a reason why testpoint phones are dying with successfull unlocks

[s4sajii]

Its not LCD fault.
i simply cut the shield very carefully. nothing went wrong. than before i proceed i put the battery in the phone and power on it. and stranage there is no LCD. but if i put the phone into testmode the back light of LCD glows.
than i went for the tp and unlock it with SC. every thing went perfact. and phone is unlocked and working but No lcd.
than i have change the LCD with the another phone but still No LCD.

Could it be flashing fault ? but how the flash fault could happen when i did not touch it with any s.w. :confuse
br

[.::Indian::.]

Originally Posted by s4sajii

Its not LCD fault.
i simply cut the shield very carefully. nothing went wrong. than before i proceed i put the battery in the phone and power on it. and stranage there is no LCD. but if i put the phone into testmode the back light of LCD glows.
than i went for the tp and unlock it with SC. every thing went perfact. and phone is unlocked and working but No lcd.
than i have change the LCD with the another phone but still No LCD.
Could it be flashing fault ? but how the flash fault could happen when i did not touch it with any s.w. :confuse
br

hi bro,
I have same problem,did u fix ur problem,if yes ple tell me how can fix it.i am waiting ur reply.




thx
santhosh

[Raklm]

u can try flashing it
if is sw problem will solve

BR
Rak|m

[abbasi73]

Originally Posted by mobilelink44

hi folks i unlocked an l7 the unlock was successful but my lcd showing no display now

my customer going mental any ideas

i have seen your phone it's a hardware damage while removing the metal shield