c975 dead after unlocking - GSM-Forum

maxwell owusu · 03-10-2008, 13:59

Hello, my c975 is dead after unlocking it. the boot is 6.3.6. The phone is not reading again if i try to connect it to smart-clip. I have tried TP it did not work. but can be switch to boot mode by pressing PWR + * + # but still cant read. Plz help me bring the phone to life. THANKS.

Lhick · 03-11-2008, 03:21

Flash the phone with its Original version Mate.

maxwell owusu · 03-11-2008, 10:59

The phone cannot be detected by smart-clip if i connect it. I have the original flash file for flashing it. PLZ HELP.

GSM_Support · 03-11-2008, 11:14

If the phone can be turned ON in boot mode then it suppose to get detected. Please ensure you have connected data cable properly.

Best Regards
GSMServer team

maxwell owusu · 03-11-2008, 12:08

The cable is properly connected but in boot mode, the data transfer is serial not USB. Is it correct?

Mr.Tinkertrain · 03-11-2008, 14:34

@ maxwell owusu,

Clean connector of the handset abd try to use another data cable. After that try to perform Repair PDS/Full Flash procedures once again.

P.S.

Quote:

the data transfer is serial not USB. Is it correct?

This phone model uses P2k cable.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

maxwell owusu · 03-11-2008, 16:28

I've done what u ask me to do but still the phone cannot be read. I have change the cable too. This is the boot mode message if i press power +*+#:
Boot Loader
0.6.3.6
SW Version: R245_U_82.21.91I
Battery OK
ok to Program
Transfer Mode:
serial RS-232

At first, immediately after unlocking, the phone went off and I flashed it with c975_R24_U_80.2F.3B.00.02. After that it did not switch on and I wont to flash it with the original flash file but the phone is not connecting at all. Plz thank you very much for your support i appreciate it OK. Help me bring the phone back to life. THANKS

Mr.Tinkertrain · 03-11-2008, 16:37

@ maxwell owusu,

As the phone can enter in boot mode, it suppose to be read by SmartMoto via Smart-Clip.
In case if it can not be detected at all, try to connect it via TestPoint.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

gsmservices · 03-12-2008, 07:56

try it out with modified repair cable

kobi. · 03-12-2008, 11:18

can the flash file used earlier cause the phone not to read again?

Mr.Tinkertrain · 03-12-2008, 11:21

@ kobi.,

Please explain in more details what problem you have.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

kobi. · 03-12-2008, 11:59

Quote:

Originally Posted by maxwell owusu

I've done what u ask me to do but still the phone cannot be read. I have change the cable too. This is the boot mode message if i press power +*+#:
Boot Loader
0.6.3.6
SW Version: R245_U_82.21.91I
Battery OK
ok to Program
Transfer Mode:
serial RS-232

At first, immediately after unlocking, the phone went off and I flashed it with c975_R24_U_80.2F.3B.00.02. After that it did not switch on and I wont to flash it with the original flash file but the phone is not connecting at all. Plz thank you very much for your support i appreciate it OK. Help me bring the phone back to life. THANKS

please this is what i mean

maxwell owusu · 03-14-2008, 14:51

The phone is working now. Thank you all for you contribution and support.

03-10-2008, 13:59	#1 (permalink)
maxwell owusu Major Poster Join Date: May 2006 Posts: 49 Member: 272683 Status: Offline Thanks Meter: 0	c975 dead after unlocking Hello, my c975 is dead after unlocking it. the boot is 6.3.6. The phone is not reading again if i try to connect it to smart-clip. I have tried TP it did not work. but can be switch to boot mode by pressing PWR + * + # but still cant read. Plz help me bring the phone to life. THANKS.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
C975 dead after unlock	freshwhite	Motorola P2k	1	09-18-2008 13:25
C975 Dead After Unlock	TAZMAN	Ultima Box Light	19	01-19-2007 10:27
C975 dead after unlock with TP	atled	Smart-Clip	3	08-15-2006 13:42
c975 dead after unlock by test point	tunscomm22	Motorola P2k	3	06-22-2006 15:58
HELP! C975 dead after unlock	drdjolens	Smart-Clip	1	06-16-2006 18:12

03-11-2008, 03:21	#2 (permalink)
Lhick No Life Poster Join Date: Aug 2006 Location: InsideOut Posts: 5,657 Member: 333359 Status: Offline Thanks Meter: 91	Flash the phone with its Original version Mate.

03-11-2008, 10:59	#3 (permalink)
maxwell owusu Major Poster Join Date: May 2006 Posts: 49 Member: 272683 Status: Offline Thanks Meter: 0	The phone cannot be detected by smart-clip if i connect it. I have the original flash file for flashing it. PLZ HELP.

03-11-2008, 11:14	#4 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	If the phone can be turned ON in boot mode then it suppose to get detected. Please ensure you have connected data cable properly. Best Regards GSMServer team

03-11-2008, 12:08	#5 (permalink)
maxwell owusu Major Poster Join Date: May 2006 Posts: 49 Member: 272683 Status: Offline Thanks Meter: 0	The cable is properly connected but in boot mode, the data transfer is serial not USB. Is it correct?

03-11-2008, 16:28	#7 (permalink)
maxwell owusu Major Poster Join Date: May 2006 Posts: 49 Member: 272683 Status: Offline Thanks Meter: 0	I've done what u ask me to do but still the phone cannot be read. I have change the cable too. This is the boot mode message if i press power +*+#: Boot Loader 0.6.3.6 SW Version: R245_U_82.21.91I Battery OK ok to Program Transfer Mode: serial RS-232 At first, immediately after unlocking, the phone went off and I flashed it with c975_R24_U_80.2F.3B.00.02. After that it did not switch on and I wont to flash it with the original flash file but the phone is not connecting at all. Plz thank you very much for your support i appreciate it OK. Help me bring the phone back to life. THANKS

03-11-2008, 16:37	#8 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ maxwell owusu, As the phone can enter in boot mode, it suppose to be read by SmartMoto via Smart-Clip. In case if it can not be detected at all, try to connect it via TestPoint. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

03-12-2008, 07:56	#9 (permalink)
gsmservices No Life Poster Join Date: Dec 2004 Age: 48 Posts: 790 Member: 101827 Status: Offline Thanks Meter: 23	try it out with modified repair cable

03-12-2008, 11:18	#10 (permalink)
kobi. Freak Poster Join Date: Feb 2008 Posts: 105 Member: 712316 Status: Offline Thanks Meter: 1	can the flash file used earlier cause the phone not to read again?

03-12-2008, 11:21	#11 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ kobi., Please explain in more details what problem you have. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

03-14-2008, 14:51	#13 (permalink)
maxwell owusu Major Poster Join Date: May 2006 Posts: 49 Member: 272683 Status: Offline Thanks Meter: 0	The phone is working now. Thank you all for you contribution and support.