c975 -only black screen after tried unlock - GSM-Forum

zonetrichur · 07-30-2006, 13:19

HALLOW FRIENDS,
C975 CAME TO UNLOCK-MADE TP PROCEDURE,BACK UP PHONE FLASH,THEN TRIED UNLOCK VIA TP-AN ERROR MESSAGE SHOWS DURING UNLOCK ( I TRIED AGAIN) -THERE AFTER WHEN SET ON SET SHOWS ONLY BLACK SCREEN WITH THE FOLLOWING DETAILS"boot loader 0.6.3.1 ,sw version R24_U_80.2F.36.00.06P,MEM MAP BLANK ,service required,batt ok,ok to program ,transfer mode :serial rs-232"
so then tried to repair pds-it shows error message "Login request... OK
Writing section0 done
Writing section1 C4/C4... 100% 3.1 Kb/sec sector erase error
Extended sector erase error code is A00080" tried many times same error message as above
then i tried to restore phone flash,it shows error message"Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Sending boot... failed
Warning: Phone may need "Remove RSA" procedure to get unlocked or flashed, check model list"so i tried remove rsa also.it took place.after remove rsa also can not be able to flash

please help me

Siemens man · 10-12-2006, 21:22

hi man
do you solve your problem? i have same problem
please help me
thanks a lot

Quote:

Originally Posted by zonetrichur

HALLOW FRIENDS,
C975 CAME TO UNLOCK-MADE TP PROCEDURE,BACK UP PHONE FLASH,THEN TRIED UNLOCK VIA TP-AN ERROR MESSAGE SHOWS DURING UNLOCK ( I TRIED AGAIN) -THERE AFTER WHEN SET ON SET SHOWS ONLY BLACK SCREEN WITH THE FOLLOWING DETAILS"boot loader 0.6.3.1 ,sw version R24_U_80.2F.36.00.06P,MEM MAP BLANK ,service required,batt ok,ok to program ,transfer mode :serial rs-232"
so then tried to repair pds-it shows error message "Login request... OK
Writing section0 done
Writing section1 C4/C4... 100% 3.1 Kb/sec sector erase error
Extended sector erase error code is A00080" tried many times same error message as above
then i tried to restore phone flash,it shows error message"Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Sending boot... failed
Warning: Phone may need "Remove RSA" procedure to get unlocked or flashed, check model list"so i tried remove rsa also.it took place.after remove rsa also can not be able to flash

please help me

Mr.Tinkertrain · 10-13-2006, 08:32

@ Siemens man,

Please post log file here, don't forget to hide your serial number.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Siemens man · 10-13-2006, 23:27

hi man
please help me. please look pic
thanks a lot

Quote:

Originally Posted by Mr.Tinkertrain

@ Siemens man,

Please post log file here, don't forget to hide your serial number.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

c_ahmad79 · 10-14-2006, 06:48

Quote:

Originally Posted by Siemens man

hi man
please help me. please look pic
thanks a lot

you get this problem after unlock..................?

SMDSAFE · 10-14-2006, 06:58

use usb-smart cyclone P2K.then try pds.

Mr.Tinkertrain · 10-14-2006, 10:10

@ Siemens man,

try to Full Flash the phone using external power supply, recommended settings are 3.7V-3.9V and 0.5А.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Siemens man · 10-14-2006, 19:05

yes i have this problem after unlock

Quote:

Originally Posted by c_ahmad79

you get this problem after unlock..................?

Siemens man · 10-14-2006, 19:41

hi mna
thank you for reply mail. i'm using external power to phone result is same
how to flash? help me
thanks a lot

Quote:

Originally Posted by Mr.Tinkertrain

@ Siemens man,

try to Full Flash the phone using external power supply, recommended settings are 3.7V-3.9V and 0.5А.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

c_ahmad79 · 10-14-2006, 19:41

sir repeat the unlock procedure again................ you can use usb smart or smart clip.........i am sure no need to flash ... you phone will be alive......

soft1hard1 · 10-14-2006, 20:25

Quote:

Originally Posted by zonetrichur

HALLOW FRIENDS,
C975 CAME TO UNLOCK-MADE TP PROCEDURE,BACK UP PHONE FLASH,THEN TRIED UNLOCK VIA TP-AN ERROR MESSAGE SHOWS DURING UNLOCK ( I TRIED AGAIN) -THERE AFTER WHEN SET ON SET SHOWS ONLY BLACK SCREEN WITH THE FOLLOWING DETAILS"boot loader 0.6.3.1 ,sw version R24_U_80.2F.36.00.06P,MEM MAP BLANK ,service required,batt ok,ok to program ,transfer mode :serial rs-232"
so then tried to repair pds-it shows error message "Login request... OK
Writing section0 done
Writing section1 C4/C4... 100% 3.1 Kb/sec sector erase error
Extended sector erase error code is A00080" tried many times same error message as above
then i tried to restore phone flash,it shows error message"Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Sending boot... failed
Warning: Phone may need "Remove RSA" procedure to get unlocked or flashed, check model list"so i tried remove rsa also.it took place.after remove rsa also can not be able to flash

please help me

@all

your TP circuit open by bad remove green protect layer, try make it "close" again by soldering,then unlock again

07-30-2006, 13:19	#1 (permalink)
zonetrichur No Life Poster Join Date: Mar 2006 Location: india Posts: 1,395 Member: 239168 Status: Offline Thanks Meter: 104	c975 -only black screen after tried unlock HALLOW FRIENDS, C975 CAME TO UNLOCK-MADE TP PROCEDURE,BACK UP PHONE FLASH,THEN TRIED UNLOCK VIA TP-AN ERROR MESSAGE SHOWS DURING UNLOCK ( I TRIED AGAIN) -THERE AFTER WHEN SET ON SET SHOWS ONLY BLACK SCREEN WITH THE FOLLOWING DETAILS"boot loader 0.6.3.1 ,sw version R24_U_80.2F.36.00.06P,MEM MAP BLANK ,service required,batt ok,ok to program ,transfer mode :serial rs-232" so then tried to repair pds-it shows error message "Login request... OK Writing section0 done Writing section1 C4/C4... 100% 3.1 Kb/sec sector erase error Extended sector erase error code is A00080" tried many times same error message as above then i tried to restore phone flash,it shows error message"Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found Switching to flash mode... OK Reading phone boot version... 3.10 Sending boot... failed Warning: Phone may need "Remove RSA" procedure to get unlocked or flashed, check model list"so i tried remove rsa also.it took place.after remove rsa also can not be able to flash please help me

10-13-2006, 08:32	#3 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ Siemens man, Please post log file here, don't forget to hide your serial number. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com Last edited by Mr.Tinkertrain; 10-13-2006 at 08:50.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
K800 White Screen After Trying to Unlock	ak47-afg	Sony Ericsson	7	05-11-2009 06:04
c975 black screen after tried unlock in smart clip	zonetrichur	Motorola P2K (USB-Smart)	0	07-30-2006 13:23
zulea V3x black screen after unlock need help	wbiz10	Motorola P2K (USB-Smart)	2	03-26-2006 00:53
3330 v4.16 black screen after botched unlock	SuBtaFuGe	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	16	01-09-2002 22:03
3330 v4.16 black screen after botched unlock-please ignore this one, dupl. msg.sorry	SuBtaFuGe	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	01-08-2002 22:00

10-14-2006, 06:58	#6 (permalink)
SMDSAFE Freak Poster Join Date: Jul 2006 Location: MARS Posts: 379 Member: 311990 Status: Offline Thanks Meter: 146	use usb-smart cyclone P2K.then try pds.

10-14-2006, 10:10	#7 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ Siemens man, try to Full Flash the phone using external power supply, recommended settings are 3.7V-3.9V and 0.5А. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

10-14-2006, 19:41	#10 (permalink)
c_ahmad79 No Life Poster Join Date: Jan 2006 Location: inside emmc ufs Age: 19 Posts: 7,188 Member: 221603 Status: Offline Sonork: 100.1581270 Thanks Meter: 6,395	sir repeat the unlock procedure again................ you can use usb smart or smart clip.........i am sure no need to flash ... you phone will be alive......