Here is a dead E1070 for smart clip

[gsm3005]

here is daed E1070
first phone was ok i try to unlock with prepare that went throug and phone unlocked but still asking for subsday pass then i try repair pds and flash went throw when flash complete phone not power up even *#pw not work so
i try to flash again with diffrent flash file there no other option have to do tp

now other any tool can't flash this phone only smart but not power

any idea please
like same phone
boot loader 0.6.8.1
Firmware R252211LD_U_85.97.F11P
Flex version USE1070H3GUKR2522102D

any flash file recommended to flash

SmartMoto 2.19
S-Card: bla bla Smart-Clip dongle, v 1.15, assigned Smart-Clip: xxxxxxxxxx Europe, initializing... OK
Clip serial: xxxxxxxxxxxx, version: 3.14, initializing... OK
Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading flash id... Intel - 28F256L18B (x2)
Phone group: E770,E1000,E1070,V3x,V975,V1050
Hardware IMEI: xxxxxxxxxxxx
WARNING! Your phone may not power on after downgrading firmware version. This phone can be unlocked only via patching.
Security area saved to "PDS for S Blank Rainbow POG xxxxxxxxxxxxxxxx (3).mbk"
Login request... OK
Writing flash section 2 of 2... 100% (83.6 Kb/sec)
Restarting phone... OK
Searching for phone... found S Blank Rainbow POG
Switching to flash mode... OK
WARNING! Your phone may not power on after downgrading firmware version. This phone can be unlocked only via patching.
Repair PDS request... OK
Performing PDS repair... OK
Writing flash section 1 of 1... 100% (20.2 Kb/sec)
Please write a corresponding Full_flash file to phone to complete repair
Writing flash section 2 of 2... 100% (81.7 Kb/sec)
Turning phone off... OK
Flash completed!

[Mr.Tinkertrain]

As log files shows

WARNING! Your phone may not power on after downgrading firmware version. This phone can be unlocked only via patching.

After the phone firmware version was downgraded it don't turn on.

If you have made a backup, flash the handset with it.
If backup wasn't made, try to find R252211LD_U_85.97.F11P firmware version and flash the phone with it.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[gsm3005]

Originally Posted by Mr.Tinkertrain

As log files shows

thanks for ur reply
power problem solved by flashing same file. boot-loader.com have this file i got from there Firmware R252211LD_U_85.97.F11P

phone can power up now . but phone still lock after all that waste of time so anyway there to unlock this phone or not

as log files shows can be unlock by patching so how to patch in patching list not listed this model

or i have to accept this firmware can't be unlock at the moment

BR
gsm3005

[Mr.Tinkertrain]

@ gsm3005,

This firmware version is not currently supported.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[pepik]

yes this phone sw version ii not able unlock this time i try too but without sucess

[kushstha]

Originally Posted by Mr.Tinkertrain

As log files shows
After the phone firmware version was downgraded it don't turn on.

If you have made a backup, flash the handset with it.
If backup wasn't made, try to find R252211LD_U_85.97.F11P firmware version and flash the phone with it.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

i tried to backup flash file from a good running handset with the same firmware 85.97.F11P.....but couldn't.........
error comes as..i/o timeout
and "critical error" appears in the phone..

how should i backup the flash from this handset?

[Mr.Tinkertrain]

@ kushstha,

backup can be made using Prepare cycle or via TP.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[kushstha]

Originally Posted by Mr.Tinkertrain

@ kushstha,

backup can be made using Prepare cycle or via TP.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

will u please send me the step by step procedure for this...
coz i dont want to loose this handset doing some nuisance...

regards....

[Mr.Tinkertrain]

@ kushstha,

1. Connect powered ON handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
2. Connect S-Card to PC USB port.
3. Connect power supply to Smart-Clip and power on the handset.
4. Launch SmartMoto.
5. Choose "Smart-Clip USB port" in phone connection window.
6. Press "Search". The software should perform the following steps:
* SmartMoto detects S-Card;
* SmartMoto detects Smart-Clip;
* SmartMoto detects the handset and reads all phone information.
7. Log to bookmark "Prepare".
8. Select the appropriate model from SmartMoto list. Make sure that phone model and boot version of the phone to be unlocked exactly match the model and boot version stated in the list.
9. For unlock purposes, please make sure that "Unlock automatically" option is marked.
10. Press "Prepare" button.
11. The prepare cycle starts. SmartMoto creates a Temporary Backup File* from the handset firmware.

For some models, SmartMoto will popup the following instruction to be performed:
* Remove phone’s battery;
* Insert battery back;
* Press power ON;
* Press ok in SmartMoto;
* The prepare cycle will continue.
12. At this time popup window appears at SmartMoto interface. Please follow the instructions provided therein
* Disconnect cable from the phone;
* Remove phone’s battery;
* Connect cable to the phone;
* Insert phone's battery;
* Press "Power on" key on the phone. Phone's LCD remains blank;
* Press OK in SmartMoto.
13. The handset should be detected by SmartMoto as "S Blank..." with boot 2.00 (3.00).
14. SmartMoto restores the temporary backup file
15. If the option "Unlock automatically" was marked – the handset becomes unlocked. If the option was not selected then the handset can be served for Flash, Repair PDS, Unlock or Backup purposes.

* Temporary Backup File is created by SmartMoto in work purposes and will be automatically erased from the Hard Drive as soon as unlock process is completed. If the handset was connected to SmartMoto, in boot mode the temporary backup file will not be created. In this case, after Prepare process is completed, the handset must be flashed with flash file and user data will be erased from the memory

NOTE:
If there was any mistakes made during unlock process, and the handset is in "MEM_MAP Blank" mode, then "Prepare" process has to be repeated and the handset has to be flashed with reflash or full_flash file.
At the stage 11, handset screen might display a "Critical error" message. Please, don’t be worried and strictly follow the instructions of SmartMoto.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[pmapuranga]

Mr Tinkerman, please help me.

I killed my e1070 trying to unlock by free programs. I then bought S Clip, tried flashed the phone, unloked it, says unloked, but can not switch on. Each time i try to download the ....f11p file from the support site, i am not able to resume the download, so i never get to finish with the download. Please assist, if you have the magic file, please upload it where i can download with resume.

I thank you in advance sir

[Mr.Tinkertrain]

@ pmapuranga,

Try to perform Repair PDS procedure and after that Full Falsh the phone with the same firmware version like it originally had.
In case is you have any problems with access to boot-loader.com or with file downloading, please write a letter to info[at]boot-loader.com
In letter specify your serial number, login and explain what problem you have.



Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[pmapuranga]

Thnak you sir, but i do not even know what file version it had before. I was just too excited to press unlock, and lost it. Assist. What file version should i try and download???

Originally Posted by Mr.Tinkertrain

@ pmapuranga,

Try to perform Repair PDS procedure and after that Full Falsh the phone with the same firmware version like it originally had.
In case is you have any problems with access to boot-loader.com or with file downloading, please write a letter to info[at]boot-loader.com
In letter specify your serial number, login and explain what problem you have.



Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[Mr.Tinkertrain]

@ pmapuranga,

Try to flash the phone with the highest available falsh file (R252211LD_U_85.9B.50R).



Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[pmapuranga]

I did the repair pds, goes on to say.......[1518] retrying block erase at 0x1000000.....
error bb



What does that mean?

[Mr.Tinkertrain]

@ pmapuranga,

Please show us full log file, don't forget to hide your serial number.



Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com