how to read user code on V980? - GSM-Forum

doberman · 08-02-2006, 12:23

when I conect and try to read phone - I have message- Searching for phone... found Motorola Phone (V980M), getting test interface... AT command error
This error is possible during phone turning on, you may try <Search> once again

Mr.Tinkertrain · 08-02-2006, 12:30

@ doberman,

You can try to perform the following:

1. power on the phone with any SIM
2. when it asks for user code, press MENU button
3. then it will ask for security password, enter 000000 and press OK (000000 - default security password. It might not be accepted, in case it was modified by user)
4. now you should be able to perform a Master reset & Master clear from the menu.

If that will not help, than You should make Repair PDS using TP method and after that Full flash (IF TP METHOD IS AVAILABLE FOR YOUR HANDSET).

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

doberman · 08-02-2006, 12:57

ok thanks I will try

doberman · 08-02-2006, 15:00

thanks for the quick reply. problem solved by TP and repair PDS and full flash . now test interface is ok .
thanks
good support

mutualmobile · 07-18-2007, 00:30

yes, this is very helpful, thank you very much, i just take off my user code of one v980

08-02-2006, 12:23	#1 (permalink)
doberman Freak Poster Join Date: Nov 2002 Location: Bulgaria Age: 50 Posts: 262 Member: 17745 Status: Offline Thanks Meter: 1	how to read user code on V980? when I conect and try to read phone - I have message- Searching for phone... found Motorola Phone (V980M), getting test interface... AT command error This error is possible during phone turning on, you may try <Search> once again

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to read user code for D900 ????	vnsun	UST Pro II	4	07-30-2008 07:28
how to read user code of BIRD S199	..::proudcracker::..	Infinity-Box	2	04-21-2007 09:56
how to read user code on E770v?	ktele	Smart-Clip	8	09-20-2006 09:32
how to read user code on e330?	mmanduri	UST Pro II	2	09-07-2006 10:48
How to read user code	tatospeed	Smart-Clip	3	08-02-2006 19:55

08-02-2006, 12:30	#2 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ doberman, You can try to perform the following: 1. power on the phone with any SIM 2. when it asks for user code, press MENU button 3. then it will ask for security password, enter 000000 and press OK (000000 - default security password. It might not be accepted, in case it was modified by user) 4. now you should be able to perform a Master reset & Master clear from the menu. If that will not help, than You should make Repair PDS using TP method and after that Full flash (IF TP METHOD IS AVAILABLE FOR YOUR HANDSET). Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

08-02-2006, 12:57	#3 (permalink)
doberman Freak Poster Join Date: Nov 2002 Location: Bulgaria Age: 50 Posts: 262 Member: 17745 Status: Offline Thanks Meter: 1	ok thanks I will try

08-02-2006, 15:00	#4 (permalink)
doberman Freak Poster Join Date: Nov 2002 Location: Bulgaria Age: 50 Posts: 262 Member: 17745 Status: Offline Thanks Meter: 1	thanks for the quick reply. problem solved by TP and repair PDS and full flash . now test interface is ok . thanks good support

07-18-2007, 00:30	#5 (permalink)
mutualmobile Freak Poster Join Date: May 2005 Location: New Zealand Posts: 175 Member: 146818 Status: Offline Thanks Meter: 7	yes, this is very helpful, thank you very much, i just take off my user code of one v980