How to unlock "V3 Net" ??? - GSM-Forum

booreck · 08-17-2006, 12:57

hi i got moto V3NET boot version 8.26,
so i done TP and push search,
got this:
SmartMoto 1.23
Clip serial: XXXXXXXXX, version: 2.26, initializing... OK
Searching for phone... found S Blank Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK

so i press unlock tab and moto v3 8.26
then i press remove RSA and get
this:
Reading phone boot version... 0.FF
This phone does not need "Remove RSA" procedure, you may unlock it with Smart-Clip button

so i disconnect phone and try to unlock with smart button
and get this:
RDL SIG ERROR:55:02:

any suggestions?????

Mr.Tinkertrain · 08-17-2006, 13:08

@ booreck,

please tell us what firmware version the phone has.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

booreck · 08-17-2006, 13:26

there is very big problem to get inot flash mode by *#POWER
phone blinks or dont want to get into this mode,

after 5 times try :

R374_G_0E.42.0ER_A

if i try to read flash i get:

Reading flash id... 0x0090-0x0090
Phone group: V30x,V40x,V50x,V52x,V60x
Reading OTP... error B8
Warning: OTP read failed

Mr.Tinkertrain · 08-17-2006, 13:35

@ booreck,

Reading flash id... 0x0090-0x0090 this string means that flash chip of the phone can't be read properly. There are 2 main reasons for this error:
1. The flash memory chip is damaged or doesn't communicate with the processor. In this case the phone needs hardware repair.
Connection between the chip and the PCB may be improved by the hot air.
2. Testpoint procedure was not performed properly -- just to make sure please, repeat the tp procedure.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

booreck · 08-17-2006, 14:01

1. phone reheated
2. testpoint done new, 100% good

still same, "phone dont need RSA remove usesmart button"

Mr.Tinkertrain · 08-17-2006, 14:06

@ booreck,

You don't need to perform TP to unlock this handset.

Unlocking V3 (boot ver.8.26)

You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode.
5. Part of phone firmware is reflashed.
6. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

booreck · 08-17-2006, 14:11

oh maaaaaaann, im an idiot! of course that works. thank you.
so my hard work with cutting that damned steel for nothing....

ottyone · 09-20-2006, 21:09

Quote:

Originally Posted by Mr.Tinkertrain

@ booreck,

You don't need to perform TP to unlock this handset.

Unlocking V3 (boot ver.8.26)

You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode.
5. Part of phone firmware is reflashed.
6. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

V3
BL 08.26
SW 378_G_0E.41.C3R_B

4 me this solution not works

when i get unlock the phone by "unlock button" LED RED
when i performe remove RSA - smart-moto-soft says "no RSA remove, phone con unlock by using clip-unlock-button..."
when i use clip-unlock-button LED RED
and always bootloader shows RDL SIG ERROR:55:02:

now came my solution

1. phone start in bootloader-mode
2. start P2K_Easy_Tool_v39_Cracked
3. select V3 and "unlock" (testpoint not required)
4. put the USB in phone and the computer
wait a view seconds (4-7)

(4 me, i have always runnig RadioComm in the background - when i put a moto in the usb port, i saw the status of the phone prompt (normal mode (green) / flash mode (black) with a little icon in the systray)

5. klick on "do job" in P2K_Easy_Tool_v39_cr.....

Phone found and the soft make a Bootloader downgrade, when this job is done - P2K_Easy.. will that you start manualy in bootloader mode , but you do not need that. close P2K_Easy...

6. Start Phone in normal mode and connect it to the Smart-Clip
7. Unlock Phone by pressing "Unlock Button" on the Clip - and smile

(9v / 500 mAh external Power stabil. recomented)

Best regards
(sorry 4 my bad english - but i hope anyone can read it)

Umbabaraumba · 09-20-2006, 21:22

Quote:

Originally Posted by Mr.Tinkertrain

@ booreck,

You don't need to perform TP to unlock this handset.

Unlocking V3 (boot ver.8.26)

You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode.
5. Part of phone firmware is reflashed.
6. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Thanks Brother,It's work OK!!Phone is unlocked without testpoint!!SmartClip Team is The Best in The World!!!

mido03 · 04-11-2007, 14:13

Thanks Brother,It's work OK

kaledkureshi · 07-05-2012, 19:43

Quote:

Originally Posted by Umbabaraumba

Thanks Brother,It's work OK!!Phone is unlocked without testpoint!!SmartClip Team is The Best in The World!!!

I have tried to unlock a motorola v3 and get the log as here

This phone does not need "Remove RSA" procedure, you may unlock it with Smart-Clip button

BUT where is the UNLOCK BUTTON on smart clip???

ottyone · 07-05-2012, 22:42

Quote:

Originally Posted by kaledkureshi

I have tried to unlock a motorola v3 and get the log as here

This phone does not need "Remove RSA" procedure, you may unlock it with Smart-Clip button

BUT where is the UNLOCK BUTTON on smart clip???

look at this pic

br.

kaledkureshi · 07-06-2012, 14:35

Yes, I know but it is not an actual working button its just a plastic piece stick on the smart clip with some glue......

underneath is nothing.......

GSM_Support · 07-06-2012, 15:20

@ kaledkureshi,

This Button is placed at the box for the unlock purposes of an "old" P2k/Acer phone models.
Just follow these easy steps to unlock your phone.

Best Regards
GSMServer team

kaledkureshi · 07-07-2012, 01:20

"Button function does not work for me, when I press unlock button the EG turns red from green and stays red while no effect of the phone

When I connect phone with usb to smart clip and search phone from the phone connection tab I get the log as below

SmartMoto 4.29
S-Card: XXXXXXXXXX Smart-Clip dongle, v 3.10, assigned Smart-Clip: XXXXXXXXX Europe, initializing... OK
Smart Adaptor: serial 12121212121, firmware version 1.05
Clip serial: XXXXXXXXX, version: 5.03, initializing... OK
Searching for phone... found Alcatel one touch 602 , getting test interface... interface not found
Switching to flash mode...
interface not found

While connecting with a RX-AC101 smart clip moto directly to pc and other end connect with phone, then select com port option menu select MTK models I get the log as below

SmartMoto 4.29
S-Card: XXXXXXXXXX Smart-Clip dongle, v 3.10, assigned Smart-Clip: XXXXXXXXX Europe, initializing... OK
Prolific USB-to-Serial Comm Port (COM80), provider - Prolific, drv. ver. 2.0.2.1 from 7/24/2005
Press and HOLD the Power ON button
Cancelled
Prolific USB-to-Serial Comm Port (COM80), provider - Prolific, drv. ver. 2.0.2.1 from 7/24/2005
MCU: MT6253, HW rev. A.04, SW rev. A.00
Release the Power ON button
Preparing...Com error 0x03

Please anyone tell me the CORRECT way to get at least ONE phone unlock with smart clip as till today I have not been able to unlock any phone till today, have lost many clients went back to other place!

08-17-2006, 12:57	#1 (permalink)
booreck Freak Poster Join Date: Apr 2004 Location: POLAND Age: 31 Posts: 119 Member: 63351 Status: Offline Thanks: 3 Thanked 5 Times in 4 Posts	How to unlock "V3 Net" ??? hi i got moto V3NET boot version 8.26, so i done TP and push search, got this: SmartMoto 1.23 Clip serial: XXXXXXXXX, version: 2.26, initializing... OK Searching for phone... found S Blank Neptune LTE, getting test interface... interface not found Switching to flash mode... OK so i press unlock tab and moto v3 8.26 then i press remove RSA and get this: Reading phone boot version... 0.FF This phone does not need "Remove RSA" procedure, you may unlock it with Smart-Clip button so i disconnect phone and try to unlock with smart button and get this: RDL SIG ERROR:55:02: any suggestions?????

07-06-2012, 14:35	#13 (permalink)
kaledkureshi Freak Poster Join Date: Nov 2010 Location: www.GSMunlocker.ca Posts: 113 Member: 1450247 Status: Offline Thanks: 8 Thanked 2 Times in 2 Posts	Yes, I know but it is not an actual working button its just a plastic piece stick on the smart clip with some glue...... underneath is nothing....... Last edited by kaledkureshi; 07-06-2012 at 14:44.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
HOW TO unlock SE v600i ??please help	xiongfuchen	SETool2	15	Yesterday 08:10
how to unlock "htc g-1 anroide?on mxkey?	rashidbinu	MXKEY FREE ADD-ONS: HTC Unlocker, HUAWEI and VODAFONE MODEMS Unlocker	1	03-29-2010 16:08
how to unlock iphone 3.0	louisgsm	iPhone ,iPod & iPad (Apple Inc. Products)	10	03-29-2010 15:53
nec n223i how to unlock or how to enter code?	infogsm	NEC	14	11-26-2005 12:53

08-17-2006, 13:08	#2 (permalink)
Mr.Tinkertrain Product Supporter Join Date: Feb 2006 Posts: 11,449 Member: 229997 Status: Offline Thanks: 252 Thanked 594 Times in 515 Posts	@ booreck, please tell us what firmware version the phone has. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

08-17-2006, 13:26	#3 (permalink)
booreck Freak Poster Join Date: Apr 2004 Location: POLAND Age: 31 Posts: 119 Member: 63351 Status: Offline Thanks: 3 Thanked 5 Times in 4 Posts	there is very big problem to get inot flash mode by *#POWER phone blinks or dont want to get into this mode, after 5 times try : R374_G_0E.42.0ER_A if i try to read flash i get: Reading flash id... 0x0090-0x0090 Phone group: V30x,V40x,V50x,V52x,V60x Reading OTP... error B8 Warning: OTP read failed

08-17-2006, 13:35	#4 (permalink)
Mr.Tinkertrain Product Supporter Join Date: Feb 2006 Posts: 11,449 Member: 229997 Status: Offline Thanks: 252 Thanked 594 Times in 515 Posts	@ booreck, Reading flash id... 0x0090-0x0090 this string means that flash chip of the phone can't be read properly. There are 2 main reasons for this error: 1. The flash memory chip is damaged or doesn't communicate with the processor. In this case the phone needs hardware repair. Connection between the chip and the PCB may be improved by the hot air. 2. Testpoint procedure was not performed properly -- just to make sure please, repeat the tp procedure. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

08-17-2006, 14:01	#5 (permalink)
booreck Freak Poster Join Date: Apr 2004 Location: POLAND Age: 31 Posts: 119 Member: 63351 Status: Offline Thanks: 3 Thanked 5 Times in 4 Posts	1. phone reheated 2. testpoint done new, 100% good still same, "phone dont need RSA remove usesmart button"

08-17-2006, 14:06	#6 (permalink)
Mr.Tinkertrain Product Supporter Join Date: Feb 2006 Posts: 11,449 Member: 229997 Status: Offline Thanks: 252 Thanked 594 Times in 515 Posts	@ booreck, You don't need to perform TP to unlock this handset. Unlocking V3 (boot ver.8.26) You need to use SmartMoto to unlock these models. 1. Power on the phone. 2. Connect it to PC via smart-clip, detect your phone in SmartMoto. 3. Go to Unlock bookmark, pick your model, press "Remove RSA" button. 4. Phone goes into boot mode. 5. Part of phone firmware is reflashed. 6. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip). Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

08-17-2006, 14:11	#7 (permalink)
booreck Freak Poster Join Date: Apr 2004 Location: POLAND Age: 31 Posts: 119 Member: 63351 Status: Offline Thanks: 3 Thanked 5 Times in 4 Posts	oh maaaaaaann, im an idiot! of course that works. thank you. so my hard work with cutting that damned steel for nothing....

04-11-2007, 14:13	#10 (permalink)
mido03 Insane Poster Join Date: Sep 2006 Location: morocco Posts: 89 Member: 353809 Status: Offline Thanks: 0 Thanked 3 Times in 3 Posts	Thanks Brother,It's work OK

07-06-2012, 15:20	#14 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 17,276 Member: 121052 Status: Offline Thanks: 423 Thanked 26,468 Times in 3,060 Posts	@ kaledkureshi, This Button is placed at the box for the unlock purposes of an "old" P2k/Acer phone models. Just follow these easy steps to unlock your phone. Best Regards GSMServer team

07-07-2012, 01:20	#15 (permalink)
kaledkureshi Freak Poster Join Date: Nov 2010 Location: www.GSMunlocker.ca Posts: 113 Member: 1450247 Status: Offline Thanks: 8 Thanked 2 Times in 2 Posts	"Button function does not work for me, when I press unlock button the EG turns red from green and stays red while no effect of the phone When I connect phone with usb to smart clip and search phone from the phone connection tab I get the log as below SmartMoto 4.29 S-Card: XXXXXXXXXX Smart-Clip dongle, v 3.10, assigned Smart-Clip: XXXXXXXXX Europe, initializing... OK Smart Adaptor: serial 12121212121, firmware version 1.05 Clip serial: XXXXXXXXX, version: 5.03, initializing... OK Searching for phone... found Alcatel one touch 602 , getting test interface... interface not found Switching to flash mode... interface not found While connecting with a RX-AC101 smart clip moto directly to pc and other end connect with phone, then select com port option menu select MTK models I get the log as below SmartMoto 4.29 S-Card: XXXXXXXXXX Smart-Clip dongle, v 3.10, assigned Smart-Clip: XXXXXXXXX Europe, initializing... OK Prolific USB-to-Serial Comm Port (COM80), provider - Prolific, drv. ver. 2.0.2.1 from 7/24/2005 Press and HOLD the Power ON button Cancelled Prolific USB-to-Serial Comm Port (COM80), provider - Prolific, drv. ver. 2.0.2.1 from 7/24/2005 MCU: MT6253, HW rev. A.04, SW rev. A.00 Release the Power ON button Preparing...Com error 0x03 Please anyone tell me the CORRECT way to get at least ONE phone unlock with smart clip as till today I have not been able to unlock any phone till today, have lost many clients went back to other place!