L6 dead help! - GSM-Forum

3stanGsm · 01-13-2008, 08:23

after successfull flash still dead..

tried to repair pds...

Quote:

SmartMoto 3.03
S-Card: *********xxSmart-Clip dongle, v 2.01, assigned Smart-Clip: ******xxEurope, initializing... OK
Clip serial: *********xx, version: 4.01, initializing... OK
Searching for phone... found S Blank Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 0.FF
Reading flash id... ST - M30L0R8000B0
Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80
Hardware IMEI: 351951014899099
IMEI OTP status: locked
Security area saved to "PDS for S Blank Neptune LTE 351951014899099 (4).mbk"
Login request... OK
[106] retrying block write at 0x10008000...
error BE

what's the problem?

Mr.Tinkertrain · 01-14-2008, 09:29

@ 3stanGsm,

Error BE usually shows that the PDS zone is damaged. Run Repair PDS procedure once again and after that Full Flash the phone with higher firmware version.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

robin3 · 04-27-2008, 17:52

sir i have the same problem but everytime i repair pds the L6 phone it still comes out error BE. what should i do?

GSM_Support · 04-29-2008, 10:33

What was the fw version of your phone and what version did you flash to it after PDS repairing?

Best Regards
GSMServer team

robin3 · 04-29-2008, 16:40

i couldnt see the fw version cus it cant boot mode. during my repair pds non was successful because of error BE. i tried it 5 times.

Mr.Tinkertrain · 04-30-2008, 08:51

@ robin3,

Most likely that the handset has hardware malfunction, but to be sure please post log files here.
Don't forget to hide your serial number.
Also, please tell us what problem it originally had.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
SLVR L6 Dead Help neded Pls help	mailtojaggu	GOT Motorola	7	02-12-2007 10:46
DEAD L6- Need Help	atukhi	Motorola P2k	3	12-22-2006 19:01
l6 dead.help me please	wuyong	Motorola P2k	0	11-06-2006 16:18
L6 dead after unlock ...help !	nabildeco@yahoo	Smart-Clip	9	05-16-2006 11:06

01-14-2008, 09:29	#2 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ 3stanGsm, Error BE usually shows that the PDS zone is damaged. Run Repair PDS procedure once again and after that Full Flash the phone with higher firmware version. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

04-27-2008, 17:52	#3 (permalink)
robin3 Freak Poster Join Date: Sep 2007 Age: 41 Posts: 389 Member: 591658 Status: Offline Thanks Meter: 14	sir i have the same problem but everytime i repair pds the L6 phone it still comes out error BE. what should i do?

04-29-2008, 10:33	#4 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	What was the fw version of your phone and what version did you flash to it after PDS repairing? Best Regards GSMServer team

04-29-2008, 16:40	#5 (permalink)
robin3 Freak Poster Join Date: Sep 2007 Age: 41 Posts: 389 Member: 591658 Status: Offline Thanks Meter: 14	i couldnt see the fw version cus it cant boot mode. during my repair pds non was successful because of error BE. i tried it 5 times.

04-30-2008, 08:51	#6 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ robin3, Most likely that the handset has hardware malfunction, but to be sure please post log files here. Don't forget to hide your serial number. Also, please tell us what problem it originally had. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com