Moto V171 won't unlock - GSM-Forum

8oo8oo8 · 03-23-2005, 12:23

Hello ,

I have here a moto v171 but he won;t unlock with smartclip how can i read the flash from the phone cause with smart moto you can only use the usb but this cable is rj45?

peter

GSM_Support · 03-23-2005, 15:23

Motorola C115/C116/C155/C156/E365/V171 unlocking procedure:
Power off the phone
Connect clip to the phone using RJ45 cable
Press UNLOCK button
Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
E/G led will glow green on success *
* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times)

To read the flash:
Connect your phone thru Smart-Clip (phone>RJ45cable>Smart-Clip>LPTcable>PC).

BR
Smart-Clip team

GsmHgvnl · 03-23-2005, 16:33

That doesn't work at that V171....ive tried it to..

8oo8oo8 · 03-23-2005, 23:50

hello, I.ve had a look to the cable shematic at smart clip site is the cable been modified?

My cable has 3 wires one for ground one for tx and one for rx
But on the picture i see 2 wires for the ground could this be the problem?

GSM_Support · 03-24-2005, 09:52

Yes you are right.
The cable should be made in the same way as it is shown on pinout diagram (2 wires on GND).

BR
Smart-clip neam

8oo8oo8 · 03-24-2005, 15:52

is it good enough if you make a bridge from ground to pin 6, because i only have 3 wires in my cable

The rx and tx are different by my cable to instead of 1 and 2 they are in pin 4 and 5
does that matter?

GSM_Support · 03-24-2005, 16:08

Talking about pin 6 & 7: yes you can make the bridge.
For RX & TX they have to be pin 1 & 2.

BR
Smart-Clip team

mzkahack29 · 07-14-2005, 14:50

yes you are write it's work for me...

03-23-2005, 12:23	#1 (permalink)
8oo8oo8 Freak Poster Join Date: Mar 2004 Location: Netherlands Age: 43 Posts: 108 Member: 60442 Status: Offline Thanks Meter: 6	Moto V171 won't unlock Hello , I have here a moto v171 but he won;t unlock with smartclip how can i read the flash from the phone cause with smart moto you can only use the usb but this cable is rj45? peter

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MOTO V171 not power on after unlock	allal123	Multi-Box	3	07-09-2006 09:54
100%100 moto v171 unlock pro here	free_gsmx	Motorola ODM	9	08-07-2005 05:36
MOTO - V171 GSM mobile phones >Com Data cable??	leo12345	Motorola ODM	4	02-24-2005 05:45
MOTO - V171 GSM mobile phones>Com Data cable??	leo12345	Motorola ODM	1	02-10-2005 15:34

03-23-2005, 15:23	#2 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	Motorola C115/C116/C155/C156/E365/V171 unlocking procedure: Power off the phone Connect clip to the phone using RJ45 cable Press UNLOCK button Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink E/G led will glow green on success * * After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times) To read the flash: Connect your phone thru Smart-Clip (phone>RJ45cable>Smart-Clip>LPTcable>PC). BR Smart-Clip team

03-23-2005, 16:33	#3 (permalink)
GsmHgvnl No Life Poster Join Date: Sep 2004 Location: Hoogeveen Age: 36 Posts: 574 Member: 82928 Status: Offline Thanks Meter: 17	That doesn't work at that V171....ive tried it to..

03-23-2005, 23:50	#4 (permalink)
8oo8oo8 Freak Poster Join Date: Mar 2004 Location: Netherlands Age: 43 Posts: 108 Member: 60442 Status: Offline Thanks Meter: 6	hello, I.ve had a look to the cable shematic at smart clip site is the cable been modified? My cable has 3 wires one for ground one for tx and one for rx But on the picture i see 2 wires for the ground could this be the problem?

03-24-2005, 09:52	#5 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	Yes you are right. The cable should be made in the same way as it is shown on pinout diagram (2 wires on GND). BR Smart-clip neam

03-24-2005, 15:52	#6 (permalink)
8oo8oo8 Freak Poster Join Date: Mar 2004 Location: Netherlands Age: 43 Posts: 108 Member: 60442 Status: Offline Thanks Meter: 6	is it good enough if you make a bridge from ground to pin 6, because i only have 3 wires in my cable The rx and tx are different by my cable to instead of 1 and 2 they are in pin 4 and 5 does that matter?

03-24-2005, 16:08	#7 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	Talking about pin 6 & 7: yes you can make the bridge. For RX & TX they have to be pin 1 & 2. BR Smart-Clip team

07-14-2005, 14:50	#8 (permalink)
mzkahack29 No Life Poster Join Date: Nov 2001 Location: morocco larache Age: 51 Posts: 582 Member: 7334 Status: Offline Sonork: 100.112291 Thanks Meter: 47	yes you are write it's work for me...