please help " clip communication fail" - GSM-Forum

pixel · 03-02-2008, 13:01

durring flashing or preparing for unlocking smart clip gives error " clip communication fail" i faced it with each set from three or four days , i am using 12v dry batry for power to get stable out put using from three years.
here is log of one of set, also i tryied on 3.06 and 3.11smart moto but same problem please help me to solve this error

SmartMoto 3.11
S-Card: ********* Smart-Clip dongle, v 2.06, assigned Smart-Clip: ******xx Europe,

initializing... OK
Clip serial: ******x, version: 4.06, initializing... OK

Searching for phone... found Motorola Phone (V3i), getting test interface... OK
Model V3i
Firmware R479_G_08.B5.3DR
Switching to flash mode... OK [S Flash Neptune LTE2]
Reading phone boot version... A.30
Sending boot... 40%
clip communication failed

failed
error C4

alvaroc · 03-02-2008, 14:59

try to read this post
http:///showthread.php?t=360296

zahid_gsm · 03-03-2008, 07:45

In case of getting an error "Clip communication failed", while detecting the handset, please check the output of Smart-Clip power source. For stable Smart-Clip functions minimum output is 9V & 500mA. Recommended power supply is 12V & 750mA.

Some phone models use a data cable for charging. So, as soon as it gets connected to Smart-Clip it starts charging and uses about 500mA, plus Clip requires another 130-150mA.

03-02-2008, 13:01	#1 (permalink)
pixel Freak Poster Join Date: Aug 2004 Posts: 248 Member: 78753 Status: Offline Thanks Meter: 35	please help " clip communication fail" durring flashing or preparing for unlocking smart clip gives error " clip communication fail" i faced it with each set from three or four days , i am using 12v dry batry for power to get stable out put using from three years. here is log of one of set, also i tryied on 3.06 and 3.11smart moto but same problem please help me to solve this error SmartMoto 3.11 S-Card: ******* Smart-Clip dongle, v 2.06, assigned Smart-Clip: **xx Europe, initializing... OK Clip serial: ****x, version: 4.06, initializing... OK Searching for phone... found Motorola Phone (V3i), getting test interface... OK Model V3i Firmware R479_G_08.B5.3DR Switching to flash mode... OK [S Flash Neptune LTE2] Reading phone boot version... A.30 Sending boot... 40% clip communication failed failed error C4

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PLEASE help me.. microbox community	murathand	Basic Micro-Box Software Support (SAMSUNG, HUAWEI, etc...)	1	03-18-2009 17:47
SMART-CLIP KILLED V3v and v300 and "...clip communication failed" ?!?	mayer	Smart-Clip	4	06-06-2006 12:48
Motorola C350 smart-clip " clip communication failed	jamsab18	Smart-Clip	6	01-24-2005 23:58
Please HELP fisio 120 communication problem	jamsoft	Philips	8	01-29-2004 12:50

03-02-2008, 14:59	#2 (permalink)
alvaroc No Life Poster Join Date: May 2006 Posts: 547 Member: 285006 Status: Offline Thanks Meter: 25	try to read this post http:///showthread.php?t=360296

03-03-2008, 07:45	#3 (permalink)
zahid_gsm No Life Poster Join Date: Feb 2006 Location: pakistan Age: 49 Posts: 1,295 Member: 232607 Status: Offline Sonork: 100.1585040 Thanks Meter: 260	In case of getting an error "Clip communication failed", while detecting the handset, please check the output of Smart-Clip power source. For stable Smart-Clip functions minimum output is 9V & 500mA. Recommended power supply is 12V & 750mA. Some phone models use a data cable for charging. So, as soon as it gets connected to Smart-Clip it starts charging and uses about 500mA, plus Clip requires another 130-150mA.