Smart TestPoint cable available - GSM-Forum

GSM_Support · 10-05-2007, 13:21

Dear forum members,

GSMserver team has accepted preorders for Smart TestPoint cable and starts dispatching all items.

Please be aware that Smart TestPoint cable made by GSM server team is the only fully tested and fully functional solution. We can not guaranty stable functions of Smart-Clip with the cables from other manufacturers. GSMserver team doesn’t bear any responsibility for the faults caused by cables from other manufacturers.

Smart TestPoint cable description and manual

The cable contains two TestPoint needles and a Battery Hook:

For correct Smart TestPoint cable functions the next order has to be followed.

Perform “Prepare Smart TestPoint”.
When SmartMoto prompts to disassemble the handset, please perform the following:
- Disconnect the handset and dismantle it
- Please ensure that LCD is disconnected from the board!!!
- Connect Smart TestPoint cable to the port RJ45 on Smart-Clip
- Connect data cable to the phone
- Connect battery hook to the positive (+) battery contact on PCB
- Connect needle A to the TestPoint A and hold it until the software informs that it can be disconnected
- Press OK in SmartMoto. The handset should be detected with boot version 0.00.
Unlock procedure continues.
Disconnect TP needle when SmartMoto informs to do so.

Please follow this order strictly. Do not use power from the battery. Use battery hook and ensure that it’s connected to the appropriate (“+” Positive) contact.

Everybody is welcome to place an order. Stock available.

Best Regards
GSMServer team

bhart · 10-05-2007, 13:28

I just place an order for one. Hope it be deliver fast.

snsoftkiller · 10-05-2007, 13:47

Good work, but help me to pair my scard with my smart clip. Mail sent since last month.

bonghernz · 10-05-2007, 14:06

nice... at last............

Mr.Tinkertrain · 10-05-2007, 14:14

@ SNSOFTKILLER,

Please PM me your e-mail address, and send letter once again.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

A-1Wireless · 10-05-2007, 14:45

We have them in stock. We can ship USA/Canada Over night with UPS.

simlockman1 · 10-05-2007, 15:21

very nice thx...........

emicabher · 10-05-2007, 19:56

Do you have a US reseller of this smart tp cable?

nishaon · 10-05-2007, 20:11

very nice work thx...........

harim_1981 · 10-05-2007, 20:34

very nice info.....

but it seems to be very hard to do unlocking....too...

eskerra · 10-05-2007, 22:57

@ GSM SUPPORT
One question, if dont mind.
You wrote:
"
Connect needle A to the TestPoint A and hold it until the software informs that it can be disconnected
Press OK in SmartMoto. The handset should be detected with boot version 0.00.
Unlock procedure continues.
Disconnect TP needle when SmartMoto informs to do so."

OK, in the first point says, that software will inform when TP a can be disconected.
But later in point fourth, says again disconect <<<<<<<<<tp, when Smartmoto says to do so.

?????????????
Do we have to conect it twice????, because, there is saying we have to disconect twice.

Is not so clear, at least for me, or maybe getting old, jejjejej

if you can clear it out please.

Thanks and regards.
Eskerra

kcgckc2002 · 10-06-2007, 04:49

Quote:

hold it until the software informs that it can be disconnected

will connect once only..............

**Faisal_Computer** · 10-06-2007, 06:11

very nice and THANKS ..................... !!

BR

Faisal_Computer

clearcom · 10-06-2007, 07:27

Nice One...

More Power!!!

sammy75 · 10-06-2007, 09:36

please upload the the pic where is right tp.. put, thx

10-05-2007, 13:21	#1 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 17,300 Member: 121052 Status: Offline Thanks: 425 Thanked 26,668 Times in 3,071 Posts	Smart TestPoint cable available Dear forum members, GSMserver team has accepted preorders for Smart TestPoint cable and starts dispatching all items. Please be aware that Smart TestPoint cable made by GSM server team is the only fully tested and fully functional solution. We can not guaranty stable functions of Smart-Clip with the cables from other manufacturers. GSMserver team doesn’t bear any responsibility for the faults caused by cables from other manufacturers. Smart TestPoint cable description and manual The cable contains two TestPoint needles and a Battery Hook: For correct Smart TestPoint cable functions the next order has to be followed. Perform “Prepare Smart TestPoint”. When SmartMoto prompts to disassemble the handset, please perform the following: Disconnect the handset and dismantle it Please ensure that LCD is disconnected from the board!!! Connect Smart TestPoint cable to the port RJ45 on Smart-Clip Connect data cable to the phone Connect battery hook to the positive (+) battery contact on PCB Connect needle A to the TestPoint A and hold it until the software informs that it can be disconnected Press OK in SmartMoto. The handset should be detected with boot version 0.00. Unlock procedure continues. Disconnect TP needle when SmartMoto informs to do so. *Please follow this order strictly. Do not use power from the battery. Use battery hook and ensure that it’s connected to the appropriate (“+” Positive) contact.* Everybody is welcome to place an order. Stock available. Best Regards GSMServer team

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Smart-Clip Smart TestPoint cable to V2.0 modification	tomaszkrupa	Smart-Clip	12	05-31-2008 10:00
smart testpoint when available to resellers???	kcgckc2002	Smart-Clip	0	10-04-2007 08:50
Smart TestPoint Cable Is Out	Star75	Smart-Clip	4	10-01-2007 15:42
Improvements to the Smart TestPoint Cable schematic	GSM_Support	Smart-Clip	0	09-21-2007 13:42

10-05-2007, 13:28	#2 (permalink)
bhart Freak Poster Join Date: Aug 2005 Posts: 273 Member: 170728 Status: Offline Thanks: 37 Thanked 3 Times in 3 Posts	I just place an order for one. Hope it be deliver fast.

10-05-2007, 13:47	#3 (permalink)
snsoftkiller No Life Poster Join Date: Mar 2006 Location: Inside facebook Age: 36 Posts: 2,648 Member: 250468 Status: Offline Sonork: 100.110362 Thanks: 114 Thanked 81 Times in 42 Posts	Good work, but help me to pair my scard with my smart clip. Mail sent since last month.

10-05-2007, 14:06	#4 (permalink)
bonghernz No Life Poster Join Date: Apr 2004 Location: Philippines Age: 30 Posts: 608 Member: 61810 Status: Offline Thanks: 26 Thanked 109 Times in 33 Posts	nice... at last............

10-05-2007, 14:14	#5 (permalink)
Mr.Tinkertrain Product Supporter Join Date: Feb 2006 Posts: 11,449 Member: 229997 Status: Offline Thanks: 252 Thanked 594 Times in 515 Posts	@ SNSOFTKILLER, Please PM me your e-mail address, and send letter once again. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

10-05-2007, 14:45	#6 (permalink)
A-1Wireless Junior Member Join Date: Oct 2004 Posts: 12 Member: 87413 Status: Offline Thanks: 0 Thanked 3 Times in 2 Posts	We have them in stock. We can ship USA/Canada Over night with UPS.

10-05-2007, 15:21	#7 (permalink)
simlockman1 No Life Poster Join Date: Feb 2001 Location: TURKEY Age: 43 Posts: 1,555 Member: 31165 Status: Offline Thanks: 0 Thanked 9 Times in 7 Posts	very nice thx...........

10-05-2007, 19:56	#8 (permalink)
emicabher No Life Poster Join Date: Oct 2006 Posts: 589 Member: 372188 Status: Offline Thanks: 91 Thanked 44 Times in 26 Posts	Do you have a US reseller of this smart tp cable?

10-05-2007, 20:11	#9 (permalink)
nishaon No Life Poster Join Date: Jan 2006 Location: Deep Blue G.S.M. Posts: 2,395 Member: 225229 Status: Offline Thanks: 7 Thanked 92 Times in 68 Posts	very nice work thx...........

10-05-2007, 20:34	#10 (permalink)
harim_1981 No Life Poster Join Date: Mar 2006 Location: tamilnadu, india. Posts: 2,220 Member: 243961 Status: Offline Sonork: 100.1591654 Thanks: 312 Thanked 90 Times in 62 Posts	very nice info..... but it seems to be very hard to do unlocking....too...

10-05-2007, 22:57	#11 (permalink)
eskerra Freak Poster Join Date: Dec 2005 Location: Portugal, Algarve Posts: 412 Member: 212823 Status: Offline Thanks: 5 Thanked 27 Times in 18 Posts	@ GSM SUPPORT One question, if dont mind. You wrote: " Connect needle A to the TestPoint A and hold it until the software informs that it can be disconnected Press OK in SmartMoto. The handset should be detected with boot version 0.00. Unlock procedure continues. Disconnect TP needle when SmartMoto informs to do so." OK, in the first point says, that software will inform when TP a can be disconected. But later in point fourth, says again disconect <<<<<<<<<tp, when Smartmoto says to do so. ????????????? Do we have to conect it twice????, because, there is saying we have to disconect twice. Is not so clear, at least for me, or maybe getting old, jejjejej if you can clear it out please. Thanks and regards. Eskerra

10-06-2007, 06:11	#13 (permalink)
Faisal_Computer Product Manager Join Date: Jun 2005 Location: Been lonely since that day Age: 27 Posts: 12,996 Member: 151871 Status: Offline Thanks: 41 Thanked 32,138 Times in 2,633 Posts	very nice and THANKS ..................... !! BR Faisal_Computer

10-06-2007, 07:27	#14 (permalink)
clearcom Freak Poster Join Date: Feb 2005 Location: hk, phils.,shenzhen Posts: 404 Member: 120669 Status: Offline Thanks: 248 Thanked 14 Times in 12 Posts	Nice One... More Power!!!

10-06-2007, 09:36	#15 (permalink)
sammy75 Freak Poster Join Date: Apr 2007 Posts: 486 Member: 480351 Status: Offline Thanks: 9 Thanked 5 Times in 5 Posts	please upload the the pic where is right tp.. put, thx