v3re help to phione revive and unlock - GSM-Forum

kariakala · 07-14-2012, 16:01

I tried to unlock

now it stucked in blank mode and with smart clip it shows botloader versin 4.0

I did open test point but can not prepare with smart clip

how to revive please?

kariakala · 07-14-2012, 16:53

/////////////////////////////////////////////////

kariakala · 07-15-2012, 07:28

any help from support yet not given answer
please help support team

thanks.

GSM_Support · 07-16-2012, 09:24

@ kariakala

Please check this thread. There you can find your answer.

Best Regards
GSMServer team

kariakala · 07-16-2012, 15:48

I did checked sir
its not shows any short circuit

it was stuck on flash mode
I try to flash set it stopped cause of power failure

and now set is in Sblank mode

it would be great it can be connected flash

thanks

GSM_Support · 07-16-2012, 16:57

@ kariakala

As the phone get read as "S Blank" and boot version get read as "4.00" any procedure could not be performed to this set. Flash, Repair PDS or Unlock procedure could not be performed if Argon based phone model get read in such way.
The only thing we can say for sure, is that the handset has hardware malfunction that doesn't allow any procedure to be completed successfully.
I can recommend you to double check the PCB of the phone, one of possible reasons for such problem could be damaged or shorted TP zone.

Best Regards
GSMServer team

kariakala · 07-16-2012, 17:03

ok sir I will check it tomorrow and reply you

thanks for the answer

07-14-2012, 16:01	#1 (permalink)
kariakala No Life Poster Join Date: Sep 2008 Location: India Posts: 1,963 Member: 851193 Status: Offline Sonork: 100.1615313 Thanks Meter: 348	v3re help to phione revive and unlock I tried to unlock now it stucked in blank mode and with smart clip it shows botloader versin 4.0 I did open test point but can not prepare with smart clip how to revive please?

07-14-2012, 16:53	#2 (permalink)
kariakala No Life Poster Join Date: Sep 2008 Location: India Posts: 1,963 Member: 851193 Status: Offline Sonork: 100.1615313 Thanks Meter: 348	///////////////////////////////////////////////// Last edited by GSM_Support; 07-16-2012 at 09:19. Reason: http://forum.gsmhosting.com/vbb/f268/smart-clip-rules-390723/

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
How to add a language in 51xx/61xx	tati	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	05-21-2013 19:20
How to upload a new firmware...	Brand	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	06-08-2012 18:29
IR between 6150 and IBM TP 600	favdijck	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-15-2011 13:08
Help with 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	05-25-2009 16:29

07-15-2012, 07:28	#3 (permalink)
kariakala No Life Poster Join Date: Sep 2008 Location: India Posts: 1,963 Member: 851193 Status: Offline Sonork: 100.1615313 Thanks Meter: 348	any help from support yet not given answer please help support team thanks.

07-16-2012, 09:24	#4 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	@ kariakala Please check this thread. There you can find your answer. Best Regards GSMServer team

07-16-2012, 15:48	#5 (permalink)
kariakala No Life Poster Join Date: Sep 2008 Location: India Posts: 1,963 Member: 851193 Status: Offline Sonork: 100.1615313 Thanks Meter: 348	I did checked sir its not shows any short circuit it was stuck on flash mode I try to flash set it stopped cause of power failure and now set is in Sblank mode it would be great it can be connected flash thanks

07-16-2012, 16:57	#6 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	@ kariakala As the phone get read as "S Blank" and boot version get read as "4.00" any procedure could not be performed to this set. Flash, Repair PDS or Unlock procedure could not be performed if Argon based phone model get read in such way. The only thing we can say for sure, is that the handset has hardware malfunction that doesn't allow any procedure to be completed successfully. I can recommend you to double check the PCB of the phone, one of possible reasons for such problem could be damaged or shorted TP zone. Best Regards GSMServer team

07-16-2012, 17:03	#7 (permalink)
kariakala No Life Poster Join Date: Sep 2008 Location: India Posts: 1,963 Member: 851193 Status: Offline Sonork: 100.1615313 Thanks Meter: 348	ok sir I will check it tomorrow and reply you thanks for the answer