how to repair this v3 with boot 7.0 - GSM-Forum

biochemistali · 01-06-2010, 14:37

-v3
-only key pad light blinks.
-it can enter in boot loader mode by *#
-tried repired pds
-
full flash
-but still same conditin
-need advice

SmartMoto 4.05
Looking for S-Card... not found (card readers searched: 0 of 3)
S-Card: ******* Smart-Clip dongle, v 3.03, assigned Smart-Clip: ***** Europe, initializing... OK
Clip serial: *********, version: 5.02, initializing... OK
Searching for phone... no phone found
Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 7.E0
Reading flash id... Intel - 28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80
Hardware IMEI: 355537000179657
IMEI OTP status: locked
Security area saved to "PDS for S Flash Neptune LTE 355537000179657.mbk"
Login request... OK
Writing flash section 4 of 4... 100% (8.57 Kb/sec)
Restarting phone... OK
Searching for phone... found S Blank Neptune LTE
Switching to flash mode... OK
IMEI OTP status: locked
Repair PDS request... OK
Performing PDS repair... OK
Writing flash section 2 of 2... 100% (45.9 Kb/sec)
Flash completed!

br
hamid

GSM_Support · 01-06-2010, 14:57

@ biochemistali,

What firmware version did you use for the flashing purposes?
Try to flash the set with the R374_G_0E.42.0CR firmware version.

Best Regards
GSMServer team

biochemistali · 01-06-2010, 15:16

Quote:

Originally Posted by GSM_Support

@ biochemistali,

What firmware version did you use for the flashing purposes?
Try to flash the set with the R374_G_0E.42.0CR firmware version.

Best Regards
GSMServer team

1st
log is of V3_R374_G_0E.40.3CR_lp002C_full_flash_MFW

2nd

R374_G_0E.42.0CR_lp0031_full_flash.mfw

still problem exists
SmartMoto 4.05
Looking for S-Card... not found (card readers searched: 0 of 3)
S-Card: Smart-Clip dongle, v 3.03, assigned Smart-Clip: Europe, initializing... OK
Clip serial:, version: 5.02, initializing... OK
Searching for phone... no phone found
Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 7.E0
Reading flash id... Intel - 28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80
Hardware IMEI: 355537000179657
IMEI OTP status: locked
Security area saved to "PDS for S Flash Neptune LTE 355537000179657.mbk"
Login request... OK
Writing flash section 4 of 4... 100% (8.57 Kb/sec)
Restarting phone... OK
Searching for phone... found S Blank Neptune LTE
Switching to flash mode... OK
IMEI OTP status: locked
Repair PDS request... OK
Performing PDS repair... OK
Writing flash section 2 of 2... 100% (45.9 Kb/sec)
Flash completed!
Operation log saved to "C:\Documents and Settings\taha mobiles\Desktop\SmartMoto log 06-01-2010.txt"
Login request... OK
Preparing...
io timeout
Searching for phone... no phone found
Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 7.E0
Reading flash id... Intel - 28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80
Hardware IMEI: 355537000179657
IMEI OTP status: locked
Security area saved to "PDS for S Flash Neptune LTE 355537000179657 (1).mbk"
Login request... OK
Writing flash section 4 of 4... 100% (6.51 Kb/sec)
Restarting phone... OK
Searching for phone... found S Blank Neptune LTE
Switching to flash mode... OK
IMEI OTP status: locked
Repair PDS request... OK
Performing PDS repair... OK
Writing flash section 2 of 2... 100% (42.4 Kb/sec)
Flash completed!

TICTAC_M · 01-06-2010, 17:20

after flash you tried to pach for imei change it woriking for me.

biochemistali · 01-07-2010, 10:29

not working for me.
S-Card: Smart-Clip dongle, v 3.03, assigned Smart-Clip: Europe, initializing... OK
Clip serial: , version: 5.02, initializing... OK
Searching for phone... no phone found
Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 7.E0
Reading flash id... Intel - 28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80
Hardware IMEI: 355537000179657
IMEI OTP status: locked
Security area saved to "PDS for S Flash Neptune LTE 355537000179657 (2).mbk"
Writing flash section 1 of 1... 100% (14.6 Kb/sec)
Applying IMEI patch, please wait (up to 2 minutes!)... OK
Turning phone off... OK
IMEI patch successfull, set new IMEI with the "Write" button

@ GSM_Support
after flashing R374_G_0E.42.0CR_lp0031_full_flash.mfw why on pressing *#it shows previous version info that is V3_R374_G_0E.40.3CR_lp002C_full_flash_MFW
why this previous software has struck in it.
in way to solve

biochemistali · 01-08-2010, 07:07

i need help.
please any solution!!

GSM_Support · 01-08-2010, 08:09

@ biochemistali,

Quote:

why this previous software has struck in it.

The previous version displayed in the flash mode because the handset can not start properly. It will be changed after the phone will be powered on. Try to flash the phone with higher firmware version. For example R374_G_0E.42.0ER.

Best Regards
GSMServer team

biochemistali · 01-08-2010, 12:02

How many times should i write this file. Three times i have already done but still it shows previous version v3_r374_g_0e.40.3cr

biochemistali · 01-08-2010, 12:02

How to erase flash using smart clip.

budukbol · 01-08-2010, 12:09

Quote:

Originally Posted by biochemistali

-v3
-only key pad light blinks.
-it can enter in boot loader mode by *#
-tried repired pds
-
full flash
-but still same conditin
-need advice

SmartMoto 4.05
Looking for S-Card... not found (card readers searched: 0 of 3)
S-Card: ******* Smart-Clip dongle, v 3.03, assigned Smart-Clip: ***** Europe, initializing... OK
Clip serial: *********, version: 5.02, initializing... OK
Searching for phone... no phone found
Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 7.E0
Reading flash id... Intel - 28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80
Hardware IMEI: 355537000179657
IMEI OTP status: locked
Security area saved to "PDS for S Flash Neptune LTE 355537000179657.mbk"
Login request... OK
Writing flash section 4 of 4... 100% (8.57 Kb/sec)
Restarting phone... OK
Searching for phone... found S Blank Neptune LTE
Switching to flash mode... OK
IMEI OTP status: locked
Repair PDS request... OK
Performing PDS repair... OK
Writing flash section 2 of 2... 100% (45.9 Kb/sec)
Flash completed!

br
hamid

for that boot mode, just click unlock button on your box, problem solve tested by me 100% for unlock, for repair flash fone with check overwrite boot area

GSM_Support · 01-08-2010, 12:09

@ biochemistali,

Try to perform Repair PDS procedure once again and flash the set with highest available *.mfw firmware version, R374_G_0E.42.10R_A.
Do you know what exactly had happened with this set so it stays in such condition?
What original firmware version it had?

Best Regards
GSMServer team

budukbol · 01-08-2010, 12:15

Quote:

Originally Posted by GSM_Support

@ biochemistali,

Try to perform Repair PDS procedure once again and flash the set with highest available *.mfw firmware version, R374_G_0E.42.10R_A.
Do you know what exactly had happened with this set so it stays in such condition?
What original firmware version it had?

Best Regards
GSMServer team

sir think that fone is attemted to unlock in mstool crack but unsecessfull, cos verytime i use that crack the boot loader always change to 7.0e

maxieboy · 01-08-2010, 12:20

yes i encounter that kind of problem after unlock in crack sof... just flash the orginal firmware your phone will be okay.. you dont know the original firmware just download all V3 firmware and flash it individually.. before you flash always tick the repair PDS so that the old version will over write

TICTAC_M · 01-08-2010, 17:38

tried to put boot 8.26 inside.

01-06-2010, 14:37	#1 (permalink)
biochemistali No Life Poster Join Date: Oct 2005 Location: P A K I S T A N Age: 16 Posts: 1,387 Member: 190344 Status: Offline Thanks Meter: 280	how to repair this v3 with boot 7.0 -v3 -only key pad light blinks. -it can enter in boot loader mode by # -tried repired pds - full flash -but still same conditin -need advice SmartMoto 4.05 Looking for S-Card... not found (card readers searched: 0 of 3) S-Card: **** Smart-Clip dongle, v 3.03, assigned Smart-Clip: * Europe, initializing... OK Clip serial: *******, version: 5.02, initializing... OK Searching for phone... no phone found Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found Switching to flash mode... OK Reading phone boot version... 7.E0 Reading flash id... Intel - 28F256L18B Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80 Hardware IMEI: 355537000179657 IMEI OTP status: locked Security area saved to "PDS for S Flash Neptune LTE 355537000179657.mbk" Login request... OK Writing flash section 4 of 4... 100% (8.57 Kb/sec) Restarting phone... OK Searching for phone... found S Blank Neptune LTE Switching to flash mode... OK IMEI OTP status: locked Repair PDS request... OK Performing PDS repair... OK Writing flash section 2 of 2... 100% (45.9 Kb/sec) Flash completed! br hamid

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to repair This problame this phone is Nokia 5130c-2 Ver 7.95	alkesh02	Nokia Base Band 5 ( BB-5 )	8	03-11-2010 07:43
what this mean how to repair gdfs erro with my phon	melgsm	Cruiser Suite	2	10-30-2008 18:38
how to unlock Motorola V3***R boot 06.22	leroi	Smart-Clip	3	07-14-2008 23:38
HOW TO REPAIR DEAD V3 with rocker	gsmdz	Ultima Box Light	4	04-01-2008 23:04

01-06-2010, 14:57	#2 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	@ biochemistali, What firmware version did you use for the flashing purposes? Try to flash the set with the R374_G_0E.42.0CR firmware version. Best Regards GSMServer team

01-06-2010, 17:20	#4 (permalink)
TICTAC_M No Life Poster Join Date: Aug 2006 Location: Ecuador -Andes Posts: 1,740 Member: 331361 Status: Offline Thanks Meter: 155	after flash you tried to pach for imei change it woriking for me.

01-07-2010, 10:29	#5 (permalink)
biochemistali No Life Poster Join Date: Oct 2005 Location: P A K I S T A N Age: 16 Posts: 1,387 Member: 190344 Status: Offline Thanks Meter: 280	not working for me. S-Card: Smart-Clip dongle, v 3.03, assigned Smart-Clip: Europe, initializing... OK Clip serial: , version: 5.02, initializing... OK Searching for phone... no phone found Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found Switching to flash mode... OK Reading phone boot version... 7.E0 Reading flash id... Intel - 28F256L18B Phone group: A630,E1,E37x,E39x,E55x,L6,U6,V3,V190,V330,V53x,V54 x,V55x,V62x,V635,V80 Hardware IMEI: 355537000179657 IMEI OTP status: locked Security area saved to "PDS for S Flash Neptune LTE 355537000179657 (2).mbk" Writing flash section 1 of 1... 100% (14.6 Kb/sec) Applying IMEI patch, please wait (up to 2 minutes!)... OK Turning phone off... OK IMEI patch successfull, set new IMEI with the "Write" button @ GSM_Support after flashing R374_G_0E.42.0CR_lp0031_full_flash.mfw why on pressing *#it shows previous version info that is V3_R374_G_0E.40.3CR_lp002C_full_flash_MFW why this previous software has struck in it. in way to solve

01-08-2010, 07:07	#6 (permalink)
biochemistali No Life Poster Join Date: Oct 2005 Location: P A K I S T A N Age: 16 Posts: 1,387 Member: 190344 Status: Offline Thanks Meter: 280	i need help. please any solution!!

01-08-2010, 12:02	#8 (permalink)
biochemistali No Life Poster Join Date: Oct 2005 Location: P A K I S T A N Age: 16 Posts: 1,387 Member: 190344 Status: Offline Thanks Meter: 280	How many times should i write this file. Three times i have already done but still it shows previous version v3_r374_g_0e.40.3cr

01-08-2010, 12:02	#9 (permalink)
biochemistali No Life Poster Join Date: Oct 2005 Location: P A K I S T A N Age: 16 Posts: 1,387 Member: 190344 Status: Offline Thanks Meter: 280	How to erase flash using smart clip.

01-08-2010, 12:09	#11 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	@ biochemistali, Try to perform Repair PDS procedure once again and flash the set with highest available *.mfw firmware version, R374_G_0E.42.10R_A. Do you know what exactly had happened with this set so it stays in such condition? What original firmware version it had? Best Regards GSMServer team

01-08-2010, 12:20	#13 (permalink)
maxieboy No Life Poster Join Date: Jun 2006 Location: Philippines Posts: 1,753 Member: 302596 Status: Offline Thanks Meter: 784	yes i encounter that kind of problem after unlock in crack sof... just flash the orginal firmware your phone will be okay.. you dont know the original firmware just download all V3 firmware and flash it individually.. before you flash always tick the repair PDS so that the old version will over write

01-08-2010, 17:38	#14 (permalink)
TICTAC_M No Life Poster Join Date: Aug 2006 Location: Ecuador -Andes Posts: 1,740 Member: 331361 Status: Offline Thanks Meter: 155	tried to put boot 8.26 inside.