W490 B00t 4.00 to 0C.50 Success - Page 2 - GSM-Forum

Mr.Tinkertrain · 09-06-2008, 08:19

@ rudyandremely,

Show us log file from the SmartMoto, please.
Don't forget to hide your serial numbers.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

mario_e1 · 09-07-2008, 00:01

Mr tinkertrain:
Here in this thread, they say that boot 04.00 is NOT hardware problem, when you ALWAYS said " most likely it's hardware problem"
So smart-clip damages mobile phone hardware? i dont think so...
I think there is a solution for this problem, but SC team dont have it... (anyone have it) but i want to say that THIS IS NOT hardware problem
i have already replaced Flash Chip.... and problem is the same! even when i dont replace Flash Chip, i can unlock it... (when say boot 04.00)
BR

Mr.Tinkertrain · 09-08-2008, 07:44

@ mario_e1,

Boot version get read as 4.00 in case if the set has hardware malfunction, as an option the TP could be shorted.
As Orange_Dominica have already mentioned

Quote:

Reading phone boot version... 4.00
After Removing a SMALL piece of shield and cleaning the PCB, We are READY !

The PCB of the phone was shorted, due to this reason the boot get read as 4.00 and the Prepare Smart TestPoint procedure could bot be completed successfully.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

mario_e1 · 09-08-2008, 15:54

ok, so, there isn't a solution yet for boot 04.00?
if there is: can you give me it? what do i have to remove? where should i cut?
Best Regards

Mr.Tinkertrain · 09-08-2008, 15:59

@ mario_e1,

Boot version can be read as 4.00 in case if some PCB component is shorted, flash chip is damaged, the TestPoint is damaged, etc.
Please check the mainboard of the phone.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

brad_mat · 09-14-2008, 15:00

if the phone is not yet boot 4.00, the phone is still boot if you connect the battery.. but now boot 4.00 the phone is dead..

Mr.Tinkertrain · 09-15-2008, 07:36

@ brad_mat,

Please explain in more details what problem you have, show us some log files.
Don't forget to hide your serial numbers.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

japunlock · 09-16-2008, 03:52

boot 4.00 is because some tracks are shorted below the shield part removed to acces the testpoint
i figured it out in my own problematic phone i not mean every phone have the same issue but i solved my problem by doing some soldering and praying a lot

fabulous801 · 11-15-2008, 02:54

Thanks just got mine fixed after i cut the shield and I connected to smartclip phone came on as 0x400. So I followed instructions, sprayed a bit of contact cleaner and use a toothbrush to brush off any residue of the PCB and phone came on great!

Quote:

Clip serial: xxxxxxxxx, version: 4.08, initializing... OK
Searching for phone... found S Blank Neptune LTE2, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 4.00
Boot version 0x400 is not supported for model 'W510,W490'
error 80
Searching for phone... found S Blank Neptune LTE2, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 4.00
Boot version 0x400 is not supported for model 'W510,W490'
Boot version 0x400 is not supported for model 'W510,W490'
Searching for phone... found S Blank Neptune LTE2, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 4.00
Boot version 0x400 is not supported for model 'W510,W490'
Clip serial: xxxxxxxxxxx, version: 4.08, initializing... OK
Searching for phone... found S Blank Neptune LTE2, getting test interface... interface not found
Switching to flash mode... OK
Searching for phone... found S Blank Neptune LTE2, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 4.00
Boot version 0x400 is not supported for model 'W510,W490'
Boot version 0x400 is not supported for model 'W510,W490'
Boot version 0x400 is not supported for model 'W510,W490'
Boot version 0x400 is not supported for model 'W510,W490'
Searching for phone... no phone found
Searching for phone... found Motorola Phone (W490), getting test interface... OK
Model W490
Firmware R452G_G_08.24.02R
Switching to flash mode... OK [S Flash Neptune LTE2]
Reading phone boot version... C.50
Sending boot... OK
Stored temporary backup to C:\Program Files\GsmServer\SmartMoto\temporary backup\bkp_F9019XXXXXXXXXX.bk_
Searching for phone... found Motorola Phone (W490), getting test interface... OK
Switching to flash mode... OK [S Flash Neptune LTE2]
Reading phone boot version... C.50
Sending boot... OK
Erasing flash memory OK
Sending firmware OK
Restarting phone...

Denozaur · 08-22-2012, 14:36

im hawe any probb boot only 4.00 pcb clean test point right

GSM_Support · 08-22-2012, 15:07

@ Denozaur,

In case if boot version get read as 4.00, more likely that the set has some hardware malfunction.
Please double check phone's PCB.

Best Regards
GSMServer team

Denozaur · 08-22-2012, 15:46

//////////////////////////////////////////

Denozaur · 08-22-2012, 16:04

Code:

SCout 2.01. Flashing phone "S Flash Neptune LTE2" - "R452G_G_08.24.02R"
flex "GSVPEMBATMB02NA0F4" boot C.50
with firmware "R452G_G_08.24.02R_PDS009_LP0003_DRM0113_VSTG_30E_010d_JPJAVA_G_08_W490_01_04_08R_GSVPEMBATMB02NA0DE_1FF.sbf"
Preparing firmware image...
Loading RAM downloader for bootloader...
Jumping to downloader...
Error jumping to RAM downloader
Flash failed

Denozaur · 08-22-2012, 16:11

Quote:

Originally Posted by GSM_Support

@ Denozaur,

In case if boot version get read as 4.00, more likely that the set has some hardware malfunction.
Please double check phone's PCB.

Best Regards
GSMServer team

That to me to look,
flash
processor or what chip????

mcandre · 08-23-2012, 07:44

You are trying to downgrade fw version. Flash the same or higher version. If you don't sure about the version, use "safe flashing : disable firmware downgrading" option.

08-22-2012, 15:46	#27 (permalink)
Denozaur No Life Poster Join Date: Apr 2005 Age: 44 Posts: 681 Member: 136052 Status: Offline Thanks Meter: 75	////////////////////////////////////////// Last edited by GSM_Support; 08-22-2012 at 15:58. Reason: Contained serial numbers

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to Downgrace 4.0633.74.00 To 3.0633.69.00	alanchua1314	Nokia Base Band 5 ( BB-5 )	0	05-13-2009 21:42
W490 Success Unlock 0C.50	oliverous	Smart-Clip	1	07-20-2008 05:32
unlock w5 with 0C.50	cordd	Smart-Clip	3	04-09-2008 23:54
w490 boot 0c.50 sw version; not found	zeroualot_7	Smart-Clip	1	01-09-2008 16:10
Fighter 4.00 and Interceptor 4.00 released	Lead	Cruiser Suite	77	10-04-2004 10:08

09-06-2008, 08:19	#16 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ rudyandremely, Show us log file from the SmartMoto, please. Don't forget to hide your serial numbers. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

09-07-2008, 00:01	#17 (permalink)
mario_e1 Freak Poster Join Date: Apr 2007 Posts: 118 Member: 481823 Status: Offline Thanks Meter: 0	Mr tinkertrain: Here in this thread, they say that boot 04.00 is NOT hardware problem, when you ALWAYS said " most likely it's hardware problem" So smart-clip damages mobile phone hardware? i dont think so... I think there is a solution for this problem, but SC team dont have it... (anyone have it) but i want to say that THIS IS NOT hardware problem i have already replaced Flash Chip.... and problem is the same! even when i dont replace Flash Chip, i can unlock it... (when say boot 04.00) BR

09-08-2008, 15:54	#19 (permalink)
mario_e1 Freak Poster Join Date: Apr 2007 Posts: 118 Member: 481823 Status: Offline Thanks Meter: 0	ok, so, there isn't a solution yet for boot 04.00? if there is: can you give me it? what do i have to remove? where should i cut? Best Regards

09-08-2008, 15:59	#20 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ mario_e1, Boot version can be read as 4.00 in case if some PCB component is shorted, flash chip is damaged, the TestPoint is damaged, etc. Please check the mainboard of the phone. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

09-14-2008, 15:00	#21 (permalink)
brad_mat Crazy Poster Join Date: Jul 2007 Posts: 50 Member: 547304 Status: Offline Thanks Meter: 0	if the phone is not yet boot 4.00, the phone is still boot if you connect the battery.. but now boot 4.00 the phone is dead..

09-15-2008, 07:36	#22 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ brad_mat, Please explain in more details what problem you have, show us some log files. Don't forget to hide your serial numbers. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

09-16-2008, 03:52	#23 (permalink)
japunlock No Life Poster Join Date: Oct 2004 Location: Cochabamba Age: 38 Posts: 1,610 Member: 87396 Status: Offline Thanks Meter: 64	boot 4.00 is because some tracks are shorted below the shield part removed to acces the testpoint i figured it out in my own problematic phone i not mean every phone have the same issue but i solved my problem by doing some soldering and praying a lot

08-22-2012, 14:36	#25 (permalink)
Denozaur No Life Poster Join Date: Apr 2005 Age: 44 Posts: 681 Member: 136052 Status: Offline Thanks Meter: 75	im hawe any probb boot only 4.00 pcb clean test point right

08-22-2012, 15:07	#26 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,980 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	@ Denozaur, In case if boot version get read as 4.00, more likely that the set has some hardware malfunction. Please double check phone's PCB. Best Regards GSMServer team

08-23-2012, 07:44	#30 (permalink)
mcandre No Life Poster Join Date: Mar 2006 Location: Central Europe Age: 39 Posts: 11,877 Member: 239548 Status: Offline Thanks Meter: 2,781	You are trying to downgrade fw version. Flash the same or higher version. If you don't sure about the version, use "safe flashing : disable firmware downgrading" option.