MYA L03 dead asfter flash

[lrcorales]

Hello, I want to ask you about this huawei, the fact is that I read a MYA L03 device (read device memory) and wrote it to another MYA L03 but at the end of the last one it does not turn on, the pc recognizes it as an mtk processor and I can rewrite the firmware but it always stays the same way, it does not start .. I ask you what I did wrong?

regards

here logs
Using library Brom_DLL_v7.1733.4
Searching phone in normal mode;
[connect the phone powered off to the usb cable]
Phone detected (MediaTek PreLoader USB VCOM (Android) (COM24))
Preparing to start flash mode;
Preparing to open COM24
Connecting;
Downloading DA;
Initializing;
Rid: a2454249da1f6d3325c3376019bed2b4
Requesting baudrate change;
Done;
USB SPEED: USB_HIGH_SPEED
DEVICE INFO:
BB CHIP: MT6737T [CA00, 00, 321, FF]
HW_STORAGE_EMMC: 0x484A0190 0x61344741 0x4217D432 0x4F9494BC [SIZE=0x3AC000000]
IMEI1 [OTP 0000]: 000000-00-000000-0
IMEI2 [OTP 0000]: 000000-00-000000-0
PROVIDER: N/A
USRDATA INFO: 0x102000000 SIZE: 0x2A8380000


Getting partitions info;
Reading info;
Partitions info:
[0x00080000-0x00300000]-[proinfo]
[0x00380000-0x00C80000]-[nvram]
[0x01000000-0x00A00000]-[protect1]
[0x01A00000-0x00E00000]-[protect2]
[0x02800000-0x00080000]-[lk]
[0x02880000-0x00080000]-[lk2]
[0x02900000-0x00080000]-[para]
[0x02980000-0x01000000]-[boot]
[0x03980000-0x04000000]-[recovery]
[0x07980000-0x00800000]-[logo]
[0x08180000-0x00A00000]-[expdb]
[0x08B80000-0x00480000]-[ROOTM]
[0x09000000-0x00800000]-[seccfg]
[0x09800000-0x00800000]-[oemkeystore]
[0x0A000000-0x00800000]-[secro]
[0x0A800000-0x00800000]-[keystore]
[0x0B000000-0x00500000]-[tee1]
[0x0B500000-0x00500000]-[tee2]
[0x0BA00000-0x04000000]-[log]
[0x0FA00000-0x04800000]-[oeminfo]
[0x14200000-0x04000000]-[erecovery]
[0x18200000-0x00100000]-[frp]
[0x18300000-0x02000000]-[nvdata]
[0x1A300000-0x02500000]-[metadata]
[0x1C800000-0xC0000000]-[system]
[0xDC800000-0x19000000]-[cust]
[0xF5800000-0x0C800000]-[cache]
[0x102000000-0x2A8380000]-[userdata]
[0x3AA380000-0x01000000]-[flashinfo]



Reading full dump;
Contents saved to :
C:\Users\ioskpu10\Documents\Android_MTK\firmware_b ackup\MEMORY_DUMP_HUAWEI MYA-L03_a2454249da1f6d3325c3376019bed2b4.osp

Time needed - 00:02:48


Using library Brom_DLL_v7.1813.3
Searching phone in normal mode;
[connect the phone powered off to the usb cable]
Phone detected (MediaTek PreLoader USB VCOM (Android) (COM24))
Preparing to start flash mode;
Preparing to open COM24
Connecting;
Downloading DA;
Initializing;
Rid: a791ce92f0ee3c6ae090dc4c8b15148f
Requesting baudrate change;
Done;
USB SPEED: USB_HIGH_SPEED
DEVICE INFO:
BB CHIP: MT6737T [CA00, 00, 321, FF]
HW_STORAGE_EMMC: 0x484A0190 0x61344741 0x531ED432 0x6984372C [SIZE=0x3AC000000]
IMEI1 [OTP 0000]: 000000-00-000000-0
IMEI2 [OTP 0000]: 000000-00-000000-0
PROVIDER: N/A
USRDATA INFO: 0x102000000 SIZE: 0x2A8380000


Preparing to write FULL_DUMP_PART0;
Writing FULL_DUMP_PART0;
Preparing to write FULL_DUMP_PART1;
Writing FULL_DUMP_PART1;
Preparing to write FULL_DUMP_PART2;
Writing FULL_DUMP_PART2;
Preparing to write FULL_DUMP_PART3;
Writing FULL_DUMP_PART3;
Preparing to write FULL_DUMP_PART4;
Writing FULL_DUMP_PART4;
Preparing to write FULL_DUMP_PART5;
Writing FULL_DUMP_PART5;
Preparing to write FULL_DUMP_PART6;
Writing FULL_DUMP_PART6;
Preparing to write FULL_DUMP_PART7;
Writing FULL_DUMP_PART7;
Preparing to write FULL_DUMP_PART8;
Writing FULL_DUMP_PART8;
Preparing to write FULL_DUMP_PART9;
Writing FULL_DUMP_PART9;
Preparing to write FULL_DUMP_PART10;
Writing FULL_DUMP_PART10;
Preparing to write FULL_DUMP_PART11;
Writing FULL_DUMP_PART11;
Preparing to write FULL_DUMP_PART12;
Writing FULL_DUMP_PART12;
Preparing to write FULL_DUMP_PART13;
Writing FULL_DUMP_PART13;
Preparing to write FULL_DUMP_PART14;
Writing FULL_DUMP_PART14;
Preparing to write FULL_DUMP_PART15;
Writing FULL_DUMP_PART15;
Success;

Time needed - 00:18:08

[.:hack3r2k:.]

The phoen will start only after writting a factory firmware ! try writing Maya-L41C432B140_Firmware.osp . If still dead provide me teh imei so i can chheckk which fw works with it


Br

[lrcorales]

Originally Posted by .:hack3r2k:.

The phoen will start only after writting a factory firmware ! try writing Maya-L41C432B140_Firmware.osp . If still dead provide me teh imei so i can chheckk which fw works with it


Br

ok bro thank.. i try..