T156 AYZ Successfully Unlocked via RX-Tx - GSM-Forum

Qaisar Mahmood · 03-30-2010, 08:46

Sir, I try to Open the Phone and attach RX-TX.
T156 AYZ Successfully Unlocked and Power on.

Connect phone powered on !
Start auth !
SW Ver: P1.2PU01V01.02
Imei: 35-------------
Getting config data;
Done;
Press power on !
Starting communication ...
Platform: E-Gold Voice ...
Preloader sent ....
Starting ...
Authorising ...
Loader sent ....

Flash ID(0): 0001:22C4

Reading ...
Saved: HUAWEI_P1.2PU01V01.02_35-----------_12.13.13_30.03.2010_PARTIAL.bin
Erasing ...
Writing ...
Unlocked ! Remove battery and put back !
Time needed - 00:00:55

I try to Unlocking With TP Cable. Unlocking Successfully done but Set is Dead.

Connect phone powered on !
Start auth !
SW Ver: P1.2PU01V01.02
Imei: 35-------------
Getting config data;
Done;
Press power on !
Starting communication ...
Platform: E-Gold Voice ...
Preloader sent ....
Starting ...
Authorising ...
Loader sent ....

Flash ID(0): 0001:22C4

Reading ...
Saved: HUAWEI_P1.2PU01V01.02_35----------08.13.13_29.03.2010_PARTIAL.bin
Erasing ...
Writing ...
Unlocked ! Remove battery and put back !
Time needed - 00:00:57

X-TRA · 03-30-2010, 09:06

Its dead because of that you miss your point with tp in to your set
if you not touch with stable then you must found the dead your set
always do it with very very humble to avoid this deadly unlock
now restore the partial of this set which you safe any where in your pc

Qaisar Mahmood · 03-30-2010, 09:42

http://forum.gsmhosting.com/vbb/f272...unlock-960100/

StRaNgE PeRsOn · 03-30-2010, 09:47

Quote:

Originally Posted by Qaisar Mahmood

http://forum.gsmhosting.com/vbb/f272...unlock-960100/

you mostly get dead phones due to attatchment of GND with TP cable

make sure you do not touch either of the part of needle with your fingers

Qaisar Mahmood · 03-30-2010, 11:52

Quote:

Originally Posted by StRaNgE PeRsOn

you mostly get dead phones due to attatchment of GND with TP cable

make sure you do not touch either of the part of needle with your fingers

Brother. First Read this Page.

http://forum.gsmhosting.com/vbb/f272...00/index2.html

msashami · 03-30-2010, 14:44

Quote:

Originally Posted by Qaisar Mahmood

Sir, I try to Open the Phone and attach RX-TX.
T156 AYZ Successfully Unlocked and Power on.

Connect phone powered on !
Start auth !
SW Ver: P1.2PU01V01.02
Imei: 35-------------
Getting config data;
Done;
Press power on !
Starting communication ...
Platform: E-Gold Voice ...
Preloader sent ....
Starting ...
Authorising ...
Loader sent ....

Flash ID(0): 0001:22C4

Reading ...
Saved: HUAWEI_P1.2PU01V01.02_35-----------_12.13.13_30.03.2010_PARTIAL.bin
Erasing ...
Writing ...
Unlocked ! Remove battery and put back !
Time needed - 00:00:55

I try to Unlocking With TP Cable. Unlocking Successfully done but Set is Dead.

Connect phone powered on !
Start auth !
SW Ver: P1.2PU01V01.02
Imei: 35-------------
Getting config data;
Done;
Press power on !
Starting communication ...
Platform: E-Gold Voice ...
Preloader sent ....
Starting ...
Authorising ...
Loader sent ....

Flash ID(0): 0001:22C4

Reading ...
Saved: HUAWEI_P1.2PU01V01.02_35----------08.13.13_29.03.2010_PARTIAL.bin
Erasing ...
Writing ...
Unlocked ! Remove battery and put back !
Time needed - 00:00:57

then what if someone have unlocked 100 pcs without opening??? I mean with TP cable. This is not the main reason that u unlocked with tp cable or by opening the set!!!

WBR

**.:hack3r2k:.** · 03-30-2010, 22:11

SO THIS MEANS THE TP CABLE KILLS THE PHONE AND NOT OUR SOFT !!!

Br

Qaisar Mahmood · 03-31-2010, 05:51

Quote:

Originally Posted by .:hack3r2k:.

SO THIS MEANS THE TP CABLE KILLS THE PHONE AND NOT OUR SOFT !!!

Br

jee Sir,----------------------------

Faheem Anjum · 03-31-2010, 05:54

Quote:

Originally Posted by Qaisar Mahmood

jee Sir,----------------------------

not true .... i open the set and make rx tx and restore but same problem dead so its not TP Cable problem ....

ABDULMANAN · 03-31-2010, 06:52

its only cable fault and please during process dont use box vpp use only proper supply

Faisal_Computer · 03-31-2010, 11:49

Quote:

Originally Posted by .:hack3r2k:.

SO THIS MEANS THE TP CABLE KILLS THE PHONE AND NOT OUR SOFT !!!

Br

i can't understand why people getting dead mobile after unlocking ..... i did many ufone AYZ , did not remember exact figure but its above then 500 mobiles in one time , and all done with TP CABLE and F.G. , i did not get any mobile Dead after unlock !!
Br
Faisal_Computer

.::M Irfan::. · 03-31-2010, 12:45

Quote:

Originally Posted by faisal_computer

i can't understand why people getting dead mobile after unlocking ..... I did many ufone ayz , did not remember exact figure but its above then 500 mobiles in one time , and all done with tp cable and f.g. , i did not get any mobile dead after unlock !!
Br
faisal_computer

if all members use low baud rate like 115200 then i m sure no one will get dead fone after unlock.

I have also unlock more then 600 but no one fone get dead.

Al is unlock and working well..

X-TRA · 03-31-2010, 13:51

Quote:

Originally Posted by .:hack3r2k:.

so this means the tp cable kills the phone and not our soft !!!

Br

yes the tp cable kills but also your soft can not recover it this is your soft fault
what you think?

Faheem Anjum · 03-31-2010, 14:09

Quote:

Originally Posted by X-TRA

yes the tp cable kills but also your soft can not recover it this is your soft fault
what you think?

most of sets dead with unlocking becoz for this need stand hands some time person missing the points when he doing unlocking ... but the problem is that ... okay with unlocking r bad TP set dead but after restore should need to power on the set back

but after restoring still dead ... i am also unlock many without any problem but there is many others member maybe newbe he doing set dead ... maybe its TP cable problem Maybe its software problem .. hope hack think about this what,s the main problem

malikawan · 03-31-2010, 16:57

Quote:

originally posted by faisal computer
i can't understand why people getting dead mobile after unlocking ..... i did many ufone AYZ , did not remember exact figure but its above then 500 mobiles in one time , and all done with TP CABLE and F.G. , i did not get any mobile Dead after unlock !!

I also unlock hundred of sets with tp cable but unluckly one set dead during unlocking and after restoration set not on. So main issue is bug on restoration process.

03-30-2010, 08:46	#1 (permalink)
Qaisar Mahmood No Life Poster Join Date: Jan 2006 Location: Pakistan Posts: 15,094 Member: 226457 Status: Offline Sonork: No more used Thanks Meter: 14,934	T156 AYZ Successfully Unlocked via RX-Tx Sir, I try to Open the Phone and attach RX-TX. T156 AYZ Successfully Unlocked and Power on. Connect phone powered on ! Start auth ! SW Ver: P1.2PU01V01.02 Imei: 35------------- Getting config data; Done; Press power on ! Starting communication ... Platform: E-Gold Voice ... Preloader sent .... Starting ... Authorising ... Loader sent .... Flash ID(0): 0001:22C4 Reading ... Saved: HUAWEI_P1.2PU01V01.02_35-----------_12.13.13_30.03.2010_PARTIAL.bin Erasing ... Writing ... Unlocked ! Remove battery and put back ! Time needed - 00:00:55 I try to Unlocking With TP Cable. Unlocking Successfully done but Set is Dead. Connect phone powered on ! Start auth ! SW Ver: P1.2PU01V01.02 Imei: 35------------- Getting config data; Done; Press power on ! Starting communication ... Platform: E-Gold Voice ... Preloader sent .... Starting ... Authorising ... Loader sent .... Flash ID(0): 0001:22C4 Reading ... Saved: HUAWEI_P1.2PU01V01.02_35----------08.13.13_29.03.2010_PARTIAL.bin Erasing ... Writing ... Unlocked ! Remove battery and put back ! Time needed - 00:00:57

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
T156 AYZ After Unlocking Dead	a.asifali	FuriousGold	5	03-29-2010 19:49
t156 ayz chip unlock....	mt mobiles	Vodafone Star	1	03-01-2010 08:06
my501c read info ok, unlock not, rx+tx+gnd	ZIYAAD STRYKER	SMTi	4	11-06-2009 08:19
N95 8G successfully UNLOCK via DK UNLOCKER 2	clearcom	BB5 Box by D.K.	7	12-02-2008 00:11
V190 Goes Into Boot Mode After Successful Unlock Via Testpoint	iruocoop	Smart-Clip	0	02-17-2006 16:08

03-30-2010, 09:06	#2 (permalink)
X-TRA No Life Poster Join Date: Jul 2006 Location: PAKISTAN Posts: 2,277 Member: 303790 Status: Offline Thanks Meter: 290	Its dead because of that you miss your point with tp in to your set if you not touch with stable then you must found the dead your set always do it with very very humble to avoid this deadly unlock now restore the partial of this set which you safe any where in your pc

03-30-2010, 09:42	#3 (permalink)
Qaisar Mahmood No Life Poster Join Date: Jan 2006 Location: Pakistan Posts: 15,094 Member: 226457 Status: Offline Sonork: No more used Thanks Meter: 14,934	http://forum.gsmhosting.com/vbb/f272...unlock-960100/

03-30-2010, 22:11	#7 (permalink)
.:hack3r2k:. Product Manager Join Date: Aug 2002 Location: FuriouSTeaM Posts: 53,979 Member: 15022 Status: Offline Sonork: 100.53452 Thanks Meter: 61,568	SO THIS MEANS THE TP CABLE KILLS THE PHONE AND NOT OUR SOFT !!! Br

03-31-2010, 06:52	#10 (permalink)
ABDULMANAN No Life Poster Join Date: Apr 2008 Location: LOVE A L L AH LOVE ALQURAN Posts: 1,944 Member: 754324 Status: Offline Sonork: LOVE MOHAMMAD (S.A.W) Thanks Meter: 500	its only cable fault and please during process dont use box vpp use only proper supply