U2805-1 write firmware error

[nbkappa]

hello

i have this U2805-1 full working, but i need to change language


OTZ 1646, and tried to flash this file : U2805-1V100R001C528B200SP00S_ROMANIA.otz

but have this error. see log :

Using library Brom_DLL_v5.1316.1
EMI Settings Loaded;
Searching phone;
(for some models keep SPACE or * (STAR) key pressed before inserting the cable)
Phone detected (MediaTek USB Port (COM102))
Preparing to start flash mode;
Connecting;
Downloading DA;
Initializing;
Requesting baudrate change;
Done;
DEVICE INFO:
BB CHIP: MT6276W_S0101 [CB00, 101, 6276, FF]
MEMORY: [HYNIX] HYD0SQG0MF1P [AD:B1:00] [SIZE=0x08000000]
FAT INFO: 0x04000000 SIZE: 0x04000000
Loading the file ...
Cfg done ...
File contents to write:
[50000000-50006E13] ARM_BL
[03F00000-03F22F37] ARM_EXT_BL
[58008000-5800DFEB] DUALMAC_DSP_BL
[00180000-002FDE77] PRIMARY_MAUI
[00000000-000B8FCB] DSP_ROM
[00305E78-00592947] SECONDARY_MAUI
[F4000000-F4F71B9F] ON_DEMAND_PAGING
ERROR: S_FT_BOOTLOADER_USB_DL_NOT_SUPPORT_DL_BOOT_REGION

Time needed - 00:00:02

Log file saved to: LOG_7_11_2018_10_48_15.txt



whats to do ?

thanks

[.:hack3r2k:.]

You must use serial cable for flashing


Br

[nbkappa]

Originally Posted by .:hack3r2k:.

You must use serial cable for flashing


Br

I have all RJ45 cables that came with box. Wich one to use for this device ? ( eg. FGOLD-049 )

Thanks

LE: http://www.furiousgold.com/en/phone/huawei-u2805

GW300 will do the job ?!

[.:hack3r2k:.]

Yes gw300 should work ok. But as i rememeber thaht cable was faulty. Had to swap rx withh tx. Unless you tested before and is working



Br

[nbkappa]

Originally Posted by .:hack3r2k:.

Yes gw300 should work ok. But as i rememeber thaht cable was faulty. Had to swap rx withh tx. Unless you tested before and is working



Br

still error with GW300 :

Using library Brom_DLL_v5.1316.1
EMI Settings Loaded;
COM opened ok;
Press power and keep it pressed now !
Connecting;
Downloading DA;
Initializing;
ERROR: Connection failed !
ERROR: BOOT_PHONE;

[.:hack3r2k:.]

IS that phone charged ? Did you reattach batt betwen connections ?? You have +3v on pin 1 of the cable ?



Br

[nbkappa]

Originally Posted by .:hack3r2k:.

IS that phone charged ? Did you reattach batt betwen connections ?? You have +3v on pin 1 of the cable ?



Br

1. battery fully charged.

2. pulled out battery and inserted it back

3. GW300 cable from another box, tested and full working with other phones

4. Furious Gold is made from plastic and has 2 RJ45 ports. also has a switch on one side and a USB port on the other side.

5. tried with both RJ45 ports, and same error...

[.:hack3r2k:.]

Check skype



Br