error when trying to debrand P910i with total multiserver - GSM-Forum

fricki · 06-11-2006, 15:21

I tried to debrand my P910i (A1 / vodafone branded) with the total multiserver.

Unfortunately it isn´t possible.

It is possible for me to flash the AVR, SYM, LNG without any problem.
It is also possible to flash the RLF file. Then the program says .. Please wait, calculating checksum ...

Then I get 2 error messages 0x028230 and 0x028211 and then checksum ok ....

but the mobile was locked afterwards and also the branding wasn´t removed.

Hs anyone an idea what went wrong ???

fricki · 06-13-2006, 11:54

No response from the reseller terminatordongle.com where I bought the credits and asked for support what I can do.

bosshogg · 06-15-2006, 12:59

I did the same, bought 3 credits at £8 each, unlocked OK but found WAP settiings from Vodafone to be read-only.

Updated firmware using unbranded "P910i_R4E001_EU-EMEA-APAC_Upgrade-Debrand_Firmware.AVR " (produced no change on phone), then tried the R5B SYM, LNG and RLF. Returned error 28230 and 28211 after RLF, but said checksum OK. Then locked up.

Notices that versaion 2.20 is now available, wonder if it fixes anything. Got no response to emails.

Argh!!!

bosshogg · 06-17-2006, 09:47

Was given credit to try again under v2.20 (Thanks)...

All checksums verified OK and a Success message after the download

Took out battery, replaced, powered on and Vodafone welcom ditty played Upon full boot, the phone had not lost any of its information or anything

I wonder if there is a missing step at the end of the process? Master reset required or should a power off do the trick?

It is almost as if it is going through the motions, simulating the process rather than doing it for real. No Debug flag or something left in the software ???

HELP (Please)

06-11-2006, 15:21	#1 (permalink)
fricki Junior Member Join Date: Jan 2003 Location: Austria Age: 37 Posts: 39 Member: 20158 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	error when trying to debrand P910i with total multiserver I tried to debrand my P910i (A1 / vodafone branded) with the total multiserver. Unfortunately it isn´t possible. It is possible for me to flash the AVR, SYM, LNG without any problem. It is also possible to flash the RLF file. Then the program says .. Please wait, calculating checksum ... Then I get 2 error messages 0x028230 and 0x028211 and then checksum ok .... but the mobile was locked afterwards and also the branding wasn´t removed. Hs anyone an idea what went wrong ???

06-15-2006, 12:59	#3 (permalink)
bosshogg Junior Member Join Date: Jul 2003 Posts: 7 Member: 36070 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	In the same boat as you! I did the same, bought 3 credits at £8 each, unlocked OK but found WAP settiings from Vodafone to be read-only. Updated firmware using unbranded "P910i_R4E001_EU-EMEA-APAC_Upgrade-Debrand_Firmware.AVR " (produced no change on phone), then tried the R5B SYM, LNG and RLF. Returned error 28230 and 28211 after RLF, but said checksum OK. Then locked up. Notices that versaion 2.20 is now available, wonder if it fixes anything. Got no response to emails. Argh!!!

06-17-2006, 09:47	#4 (permalink)
bosshogg Junior Member Join Date: Jul 2003 Posts: 7 Member: 36070 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Update, tried v2.20... Was given credit to try again under v2.20 (Thanks)... All checksums verified OK and a Success message after the download Took out battery, replaced, powered on and Vodafone welcom ditty played Upon full boot, the phone had not lost any of its information or anything I wonder if there is a missing step at the end of the process? Master reset required or should a power off do the trick? It is almost as if it is going through the motions, simulating the process rather than doing it for real. No Debug flag or something left in the software ??? HELP (Please)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Z1010 - Phone won't turn on, "failed to load CERTLOADERS" error when trying to flash	Kole89	Sony Ericsson	0	02-24-2008 22:00
Error when trying to attach LG U8330 to V10.10beta	A-H-T	Cruiser Suite	8	12-29-2006 11:57
error when trying to debrand z1010 with total multiserver	jonas3	TOTAL MultiServer	10	06-04-2006 13:14
C65 beep,error ?15 when trying to write map with Eeprom tool	gjurobrod	Siemens-Benq RingTones and WallPapers	5	12-15-2004 22:35
PSTGetInterfaceHandle Failed Error when trying to Recover Phone using FDI	lobetto	P2k Series	0	08-30-2004 08:29

06-13-2006, 11:54	#2 (permalink)
fricki Junior Member Join Date: Jan 2003 Location: Austria Age: 37 Posts: 39 Member: 20158 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	No response from the reseller terminatordongle.com where I bought the credits and asked for support what I can do.