ONLINE MANUAL - Tips and Tricks - SomeTimes Read Here FOR USEFULL INFOS

[Gobi]

We want to remind you that you have 3 support areas avaiable for Vygis softwares:
1 - www.VygisToolbox.com support area for Standard and Full pack softwares
2 and 3 - the automatic support areas for all Vygissoftwares, like described here:
http://forum.gsmhosting.com/vbb/showthread.php?t=253789
If you are looking for a flashfile, please check ON ALL 3 OF THEM, because not all flashfiles are on all servers.

Yesterday the solution for unlocking NEC122 was tested with success, so prepare in the next few days for that update also.
New updates for the Vygis softwares are still to come one after another.

Despite this we try to expand as much as possible also the flashfile databas.

At this moment we have on our servers:
over 10 GB of flashdata , from this 6-7GB are ONLY THE LG flashfiles
We have just uploaded some more flashfiles on the support area (like the G1600 bluescreenrepair flash, C3380, Pantech flashes).

More flashfiles will come and we will do our best to collect more and more.

If you want more and more flashfiles in the support area --> you can also readout flashfiles from new version - or new langpack phones and sent us at info at gsm-tool.com .


regards,
Gobi

[Gobi]

Problem:
>>>>> a75 unlock failed
I need unlock benq-simens ap75, v1.35 but is showed the information: unlock failed

Solution by mr Vygis:

>>>>>
Make "repair eepr" and later "phone reset".

[Gobi]

Nr1: M300_O2X1i_O2X1b_O2X2i_E61_AP75 pinout

KEYBOARD

I----------I
1 10

1 - GND
5 - RX (data to phone)
6 - TX (data from phone)

NR2: Testpoint connect to GND (you can leave it connected)

Now, if you have correct cable and TP to GND - you can do what you want with the phone using VygisToolbox O2 software and VPOwer.

regards,
Gobi

[Gobi]

by mr Vygis:

"Some firmwares from Telcel are locked forever-I mean even if you unlock them in standart way-phone still don't take other SIM,except card from Telcel.To solve this-write to phones firmwares for PG1410 and PG3210 from support sites.

Regards,Vygis"

[Gobi]

Also Here How To Acess The 2 Automatic Areas Directly From Software - Check Atachement:

[Gobi]

GENERAL REPAIR PROCEDURE ON LG native PHONES

Full flash + unlock, where is possible also write Calibration data

Try with few Full flashes from support areas.

Also try this trick:
http:///vbb/showpo...9&postcount=22

If all this don't help, and your phone is still not powering on, then it is hardware problem for your LG2 native phone.

regards,
Gobi

[KingKronik]

DO NOT FLASH A TG800 WITH KG800 FIRMWARE!!!!!

The phone will lose the 850mhz frequency, and will not gain the 900mhz frequency. This means you will be left with a DUAL BAND phone. Only flash Tg800 with Tg800 firmware, and Kg800 with Kg800/Kg90 firmware

[Gobi]

I give you here instructions received some time ago from a friend, how to activate your DEVICE MANAGER to show you ALL installed drivers, even for the devices not connected to your pc at that moment.

If you actually right-click the device in Device Manager and select Uninstall, the device and its associated drivers will be removed.
But, if you just remove the device, it will disappear from the Device Manager, but may leave the drivers behind.
Those drivers, aside from taking up space, could later be found to contain vulnerabilities and expose your system to compromise
even though you aren't aware the drivers exist.

With the device physically removed from the computer, the only way to view, and thereby have access to uninstalling,
the drivers is to alter Device Manager to Show hidden devices. Follow the steps below to display the hidden device information:

1. Right-click My Computer and select Properties
2. Click on the Advanced tab
3. Click on Environment Variables
4. Below the bottom Environment Variables window pane (System Variables), click on New
5. For Variable Name, enter devmgr_show_nonpresent_devices
6. For Variable Value, enter 1
7. Click OK to close Environment Variables and OK again to close System Properties

Now that you have created this entry, when you open Device Manager, you can click on View and then select Show hidden devices
from the menu.
You can identify the hidden devices by their grayed-out icons.


regards,
Gobi

[Gobi]

1.Some LG phones after unlocking can still be locked,if already bad codes are entered.
For unlocking completing you must reset phone.Code to reset phone(must be used if after unlocking phone still is locked or has
user code) :
2945#*# and later "Factory reset".
************************************************** **********************************
2.LG phones can have one or two flashes inside.Software by selected phone type
shows active buttons "Read flash","Write flash" if phone has only one flash,and shows active "Read flash2","Write flash2" if phone has 2 flashes.
For language-version changing you must do next:
- if phone has one flash:
- check "Firmware" at "Flasher" section,press "Write flash" and select
your wanted flash.After this,software writes flash.
- if phone has two flashes:
- check "Firmware" at "Flasher" section,press "Write flash" and select
your wanted flash.First flash also is called "CodeData" flash.After this,
software writes first flash.
- Press "Write flash2" and select second flash,it is called "AlchemyData".
After this,software writes second flash,finishing software changing procedure.
************************************************** **********************************
3.Software allows change IMEI,reset phone in "Special" section.For these procedures
phone must be ON and without SIM card.Power ON phone,connect it to cable and simply
select what you want to do.
************************************************** **********************************
4.Software allows convert original LG flashes with extensions *.mot,*m0 and *.bif
to bin files for using with "Flasher" section.
For files converting do next:
- goto "Additional" section
- select phone type,for which file must be converted(!!!!it is important)
- check "Flash#1(Code data) for first flash converting(if you will see
active label "Flash#2(Alchemy)",later you will need to convert and it.
- press "Open flash",select in opened dialog window what files type you
are converting(mot,m0 or bif) and later select original flash.
- press "Convert and Save Flash",select where your converted flash must
be saved and wait until converting will be finished.
- if your phone has 2 flashes,check "Flash#2(Alchemy)" and repeat all procedures
same as for first flash.
************************************************** ***********************************
5.Software allows to repaier "Sevice not available" after uploading russian language
flash to G7100,C1100 or C1400.For this after soft starting go to section "Unlocker" and
press CTR+R on keyboard.New button "Repaier service not available" must appear.
Repairing time-about 1 second.This function it is not tested fully,so before
using it,please read calibration data from phone.
************************************************** ***********************************
6. If you want to get mail about last updates uploaded to support FTP,you must
register to "News" section at my site:
www.vygis.net

[Gobi]

Some LG phones - like MG220 and MG 810, from some specific operators - like Claro are havine permanent-locked flashes. In order to unlock them, it is needed to flash this phones completely with flashes from other operator - avaiable on the support areas.

regards,
Gobi

[snsoftkiller]

Thanks again my CU400 unlocked sucessfully.
1st go to support download last update LGQ_1_17SC.rar and file CU400_V10b-CINGULAR[UNLOCKED]-EN_ES_FR.rar from support.

1- Install LG USB Drivers if not already in your PC (archive inside update archive LGQ_1_17SC.rar) and connect phone windows should find phone and install it automatically. When you see your hardware is installed and ready to use then go to next step.
2- Click on connect port
3- Click on connect phone
4- Read NVM and save it (dont feel lazy to do it)
5- Click on "flasher" tab
6- Click on folder icon button to search the file "CU400_V10b-CINGULAR[UNLOCKED]-EN_ES_FR.crc"
7- Click on "write files & do jobs"

In my case, 1st try something goes wrong. Dont panic, try reconnect phone by pressing 2+5+power button you will see "download mode" on phone screen. Re-do step all steps except 4. When finish you will be prompted to write back NVM cause after flashing by emergency mode this area is erased. For this do step 2, 3 and click on tab "unlocker", click on NVM write then choose your backup will be by default your phone imei name like this NV_CU400_011226-00-xxxxxx-x_2007_10_21_20_36.nv2
Now your phone is unlocked and fully working !!!


Enjoy life....

[snsoftkiller]

Thanks again my CU400 unlocked sucessfully.
1st go to support download last update LGQ_1_17SC.rar and file CU400_V10b-CINGULAR[UNLOCKED]-EN_ES_FR.rar from support.

1- Install LG USB Drivers if not already in your PC (archive inside update archive LGQ_1_17SC.rar) and connect phone windows should find phone and install it automatically. When you see your hardware is installed and ready to use then go to next step.
2- Click on connect port
3- Click on connect phone
4- Read NVM and save it (dont feel lazy to do it)
5- Click on "flasher" tab
6- Click on folder icon button to search the file "CU400_V10b-CINGULAR[UNLOCKED]-EN_ES_FR.crc"
7- Click on "write files & do jobs"

In my case, 1st try something goes wrong. Dont panic, try reconnect phone by pressing 2+5+power button you will see "download mode" on phone screen. Re-do step all steps except 4. When finish you will be prompted to write back NVM cause after flashing by emergency mode this area is erased. For this do step 2, 3 and click on tab "unlocker", click on NVM write then choose your backup will be by default your phone imei name like this NV_CU400_011226-00-xxxxxx-x_2007_10_21_20_36.nv2
Now your phone is unlocked and fully working !!!


Enjoy life....

[vygism]

IF ANY PROBLEMS WITH KE970 AFTER FLASHING:

Try to write this eeprom - ke970_354963010350584_eep.bif from attachment.

Regards,Vygis

[TCJUDAS]

if phone blinks or cant be connected in normal way disconnect it from
software and cable put off put on baterry press 2+5 and power ON buttons together display shown 3 (but not blinks)
install LGUSBModemDriver (including LGQ_1_19SC folder)
use samsung z500 cable usb+rj45 (ustpro etc.)
connect phone to cable (found new device )start software select baudrate 115200 check Enumerate PORTS and Auto find PORT choose comport (not usb serial port by vygisoft different one (LGE mobile usb serial port) )
after port connecting press connect phone
choose flash and press write files & do job
after flash writing go to Unlocker section and press Write NVM for
phone's NVM backup writing.
if phones NVM backup was not created use Repair NVM option

[Gobi]

CONVERTER HELP
================================================== ==============================
Software allows to convert original factory flashes for using with software.
For files converting do next :
- go to "Converter" section
- drag and drop all files from flash package to "Converter" window, or press
"Open" button and using "Shift" key select all files
- press "Convert & Save Files" and wait for converting finish
- if software can't find one or other needed file for converting,it
will inform you what file is needed to finish convert procedure.