ONLINE MANUAL - Tips and Tricks - SomeTimes Read Here FOR USEFULL INFOS

[Gobi]

UNLOCKER HELP
================================================== ==============================
For starting to work with software,you need to have LG USB cable-mostly is included
to phone's package and drivers-"LGUSBModemDrivers" installed.
For LG KS20 - "LGCoronaUSBDrivers" must be installed.

1.Connecting phone :
- power ON phone and connect it to USB cable
- start software
- select baudrate 115200,check "Enumerate PORTS" and "Auto find PORT"
- select phone model
- press "CONNECT PORT"
- if software writes "Can't find needed COMPORT"-check cable and drivers
instalation
- after port connecting,press "CONNECT PHONE"
- wait until software will read phone's info
- if selected phone model differs from phone type,readed from phone,
software can ask you what phone type you want to set
Some new models like CU915,CU920 and TU920 must be connected in next way :
- power OFF phone and connect it to USB cable.
- Wait until phone will power ON and will show on LCD "Battery charging",
- press "CONNECT PORT",press "CONNECT PHONE" and make your needed operations.

WARNING! Use only native PC USB port,not use any external USB hubs


2.Unlocking :
- if after connecting you see active button "Direct unlock",press it
for phone unlocking
- if you see active "Write backup" button,it means,that software creates
lock zone backup,when unlocking goes,and later if something went wrong
you can restore phone with this backup.For backup writing press "Write
backup" and you will be redirected to folder,where your phone's backup
is.All backups in name has IMEI and last digits of backup number has
date and time,when backup was created.
- if after connecting you see "Read unlock code" button active,it
means,that for this model is supported unlock code reading.
- if noone of these buttons are active,go to support and look if exist
at it flash with string "UNLOCKED" or "TEMP UNLOCK" for your phone model.
If such flash exist,it means,that your phone can be unlocked by writing
patched flash.In this case write flash with "Flasher" section.
String "TEMP UNLOCK" in flash name means,that for this phone model exist
only temporarry unlock solution.
- if at support sites not exist flashes for unlock by patching,it means,that
at this moment unlock for selected model is not supported.

2a.KS20 codes reading :
- type 2676625720# to enter engineering menu
- select Port Setting > 1. Diag Setting > 1. USB Set for Diag > "OK" > "Back"
- select (Port Setting > 1. Diag Setting >) 2. USB Switching > "LG Composite -DUN, DIAG"
- press Done and restart phone
- connect phone and press "Read codes"
- type 2945#*20# and enter unlock code.

P.S.More info how to enable DIAG Mode,can be get from "KS20 set DIAG mode.jpg"
picture.

WARNING! Not all firmwares allow to enter to DIAG Mode and read codes.If you can't
connect to software-you need to flash phone with ROM image,which allows DIAG MODE.
Such ROM images have in name "DIAG OK" string.ROMs,which in name have "NO DIAG"
string not allow DIAG Mode.How to flash KS20 read in "Flasher help.txt" file.

2b.MS20 and MS25 unlocking :
- enter phone to "Emergency download mode"
- for this press "Send(Call)" + "Function" + "Power ON"
- LED in upper right corner of phone must turn to green
- LCD display must be black
- start software,connect USB cable to phone - press "Connect Port" and "Connect Phone"
- phone must connects in emergency mode
- go to "Flasher" section and select "KS20_V10b_S_3_1_1_00215_DIAG OK_ROM_FRENCH" flash file
- "Erase EFS" must be not checked
- press "Write files & Do Jobs" and wait for process finishing
- after flashing do next :
- type 2676625720# to enter engineering menu
- select Port Setting > 1. Diag Setting > 1. USB Set for Diag > "OK" > "Back"
- select (Port Setting > 1. Diag Setting >) 2. USB Switching > "LG Composite -DUN, DIAG"
- press Done and restart phone
- connect phone in normal mode and press "Read codes"
- type 2945#*20# and enter unlock code.
- again enter to emergency mode and flash your needed MS20 or MS25 ROM flash file
in same way like was described before.

2c.KS20,MS20 and MS25 IMEI changing :
- enter phone to "Emergency download mode"
- for this press "Send(Call)" + "Function" + "Power ON"
- LED in upper right corner of phone must turn to green
- LCD display must be black
- start software,connect USB cable to phone - press "Connect Port" and "Connect Phone"
- phone must connects in emergency mode
- go to "Flasher" section and select "KS20_V10b_S_3_1_1_00215_DIAG OK_ROM_FRENCH" flash file
- "Erase EFS" must be checked,it is important
- press "Write files & Do Jobs" and wait for process finishing
- after flashing do next :
- type 2676625720# to enter engineering menu
- select Port Setting > 1. Diag Setting > 1. USB Set for Diag > "OK" > "Back"
- select (Port Setting > 1. Diag Setting >) 2. USB Switching > "LG Composite -DUN, DIAG"
- press Done and restart phone
- connect phone in normal mode and in IMEI window write your needed IMEI
- press "Repair NVM" and wait for process completing
- again enter to emergency mode and flash your needed KS20,MS20 or MS25 ROM flash file
in same way like was described before.

3. Temp unlocking :
- U300,U880,U890 and U900 can't be unlocked permanently at this moment.For
temp. unlocking,flash phones with flash from support(flash in name must have
string "TEMP UNLOCK", if your phone's region differs from flash region,
in "Flasher" section check "Change Region" and select needed region.
- after flashing do next :
- for model U880 (64k and 128k SIM supported) :
a) insert to phone yor SIM card
b) phone must write "USIM locked"
c) if you see "SOS" or "Emergency" ,press this button
and wait until phone will reboot,after rebooting
phone works with your card
d) if you don't see "SOS" or "Emergency"-type at phone's
keyboard 142358#*# and wait for phone rebooting.

- for model U900 (only 128k SIM supported) :
a) make everything same like for U880

- for models U300 and U890 (64k and 128k SIM supported) :
a) insert original 3G card to your phone
b) power ON phone and connect charger or USB cable to it
c) phone must show charging
d) go to "Menu"-"Tools"-"Unit converter" and select it
e) fast change original 3G card with your SIM card(your SIM
card must be without PIN)
f) wait untill phone will reboot

4.Other functions in "Unlocker" section :
- "Read NVM" and "Write NVM" are for phone's NVM area reading-writing
"Write NVM" is also used to write phone's NVM backup after flashing
in "EMERGENCY MODE"
- "Repair NVM" function is for NVM repairing ( no network and etc.)
- "Factory Reset" function is for phone reseting ( phone code set to
default and etc.)
- for working with these functions with KS20 - ROM which allows
DIAG Mode must be in phone.Also "Repair NVM" function allow to
fix KS20 with IMEI 000000000000000 problem.For this in IMEI
window enter your needed IMEI,before pressing "Repair NVM" button.


5.LG KS20 passwords reseting :
- power OFF phone
- press and keep "Volume down" + "Send(Call)" + "Power ON" buttons together
- LED in upper right corner of phone must turn to red,blue and green
- release pressed buttons
- phone must start ON and ask for reconfiguration

[Gobi]

FLASHER HELP
================================================== ==============================
For phone flashing do next :
- connect phone like is described in "Unlocker Help.txt" file
- drag and drop flash file with extension .crc to "Flasher" window
or press "Open" window and select needed flash file.
- select additional functions "Erase EFS" or "Change Region" and
press "Write files & Do Jobs".(Additional functions will be described
later)
- wait for flashing finish

If flashing was not finished correctly do next :
- press "Disconnect PORT" at software
- disconnect phone from cable
- put off-put on baterry,power ON phone,connect cable and try connect
with software again
- if phone blinks or can't be connected in normal way-disconnect if from
software and cable,put off-put on baterry,press 2,5 and power ON buttons together
on phone's keyboard-phone must enter to "EMERGENCY" mode
- connect phone to cable,connect with software and write flash file
- after flash writing go to "Unlocker" section and press "Write NVM" for
phone's NVM backup writing.
- if phone's NVM backup was not created-use "Repair NVM" option

Additional "Flasher" section options :
- "Erase EFS" option allows full EFS,including all user data and nvm fields,erasing.
For flashing is recomended to use this option,for using simple check it.This function
allows to have shorter flashing time for about 40-50 seconds.Not use it for KS20.
If you don't want to erase user data,don't use this option.
- "Change Region" option is for region changing in flash "MEDIA" file.
LG Qualcomm phones from H3G network has different "MEDIA" files,depending from
country-region.If you will write flash with not correct region-phone will show
"Unavailable MEDIA file".If flash file,which you want to write to phone has different
region from you phone's country,before flash writing check "Change Region" and select
needed country-region.

LG KS20 flashing :
- LG KS20 flashing differs from all other LGQ phones flashing
- for KS20 flashing-enter to Emergency download mode
- for this press "Send(Call)" + "Function" + "Power ON"
- LED in upper right corner of phone must turn to green
- LCD display must be black
- start software,connect USB cable to phone - press "Connect Port" and "Connect Phone"
- phone must connects in emergency mode
- select one or other flash file,depending what you want to do-change language or
enable DIAG Mode
- uncheck "Erase EFS" checkbox
- press "Write files & Do Jobs" and wait for process finishing

P.S.More info how to enter to emergency mode,can be get from "KS20 emergency mode.jpg"
picture.

ENTERING TO EMERGENCY MODE COMBINATIONS :
- for CU915,TU915,CU920 - press "Volume down"+"Lock"+"Camera"+"Power ON"- on the screen
must appear "Emergency Download"
- for KS20 - look to picture "KS20 emergency mode.jpg"
- for KE990,KU990 - press "Send"+"C"+"Camera"+"Power ON"-on the screen
must appear "Emergency Download"
- for KC910 - press "Send"+"Menu"+"Camera"+"Power ON"-on the screen
must appear "Emergency Download"
- for all others - press "2","5" and "PowerON" together

SOME FLASHING HINTS :

U8210 and U8290 sometimes after flashing can stuck on booting logo-mainly this happens on
already unlocked phones.In this case use "Repair NVM" function,after this phone must power
ON in normal way only,but must be locked again.Use "Direct unlock" function to unlock it
again.

[Gobi]

- FIRST IN THE WORLD added full support,including fast unlock(10-15 seconds),flash reading-writing,IMEI changing and phone reseting for LG240 and ME240q models.
For flashing-unlocking use U8110 cable,for service functions(ReadIMEI,Write IMEI,Phone reset) use LG7050 cable.

- Fixed fast direct unlock for KE500,ME550 models,now unlock must work on all known version and unlock time is less than 10 sec.It means-you don't need now to flash phone for unlock.

- Implemented eeprom (calibration data,IMEI and locks zone) reading-writing for KE500,ME550 models.
Use this function for phones repairing-read eeprom from working phone,write it later to not working phone,if phone freeze at "LG" logo,after this write anyone flash from support site-phone must start to work properly if hardware is OK.
Later restore original IMEI with functions "Read IMEI" - "Write IMEI",using LG KG800 cable.

[Gobi]

NR1: ON THE SUPPORT WEBSITE: www.VygisToolbox.com

NR2: http://forum.gsmhosting.com/vbb/showthread.php?t=480927

regards,
Gobi

[Gobi]

http:///vbb/showthread.php?t=483782

ALL LG PHONES PINOUT IS THERE.

regards,
Gobi

[vygism]

Here is one

Regards,Vygis

[mtony969]

its uploaded here m8

[vygism]

If you was making cable from KG800 cable,check all GND pins,I have reports,that in some KG800 cables is mistake-not pin 4,but pin 5 is connected to GND.Also check what levels are on box RX and TX pins-they must be 3,3V,if they are 5 V - also you won't can work correctly.

Regards,Vygis

[TICTAC_M]

well ce110 is unlock with path, very easy you need download unlock flash of support, flash with it the phone, ok phone unlock.

direct unlock is not support for it phone - is for it that bottom disable. procedure same cu500, cu400 and more.

remember you need ke500 cable for it.

[vygism]

Read full flash backup and later write fw from KG285.Basically MG160,KG270,KG271,KG275,KG276,KG278,KG285,KG289 are same phone and you can write fw from one phones to others.

Regards,Vygis

[vygism]

For MU500 unlock-write to phone anyone flash for CU500 or TU500.With IMEI-sorry,I can't help.

Regards,Vygis

[vygism]

Basically MG370,KG370 and KG375 is same phone.At support sites exist full repair flash for Kg370,it can be used and for Kg375-this in case,if you don't have readed flash from working phone

Regards,Vygis

[Gobi]

New version - Pantech/Innostream flasher-unlocker v1.23SC is uploaded in "O2" section at support sites.

Added full support for Pantech S100.S100 pinout differs from old Pantech pinouts,needed pinout you can find in "Pinout info.txt" file.

WARNING ! S100 from TELCEL can't be unlocked directly-for unlocking you need to flash it with S100_INAC0605072007_EN_PT_ES_fw #1 flash.

regards,
Gobi

[vygism]

Kp130 unlock


Try connect it like KG130 with KE500 cable,read full flash and full flash_#2 and after this make "Repair service not available".

Regards,Vygis

[kobolt]

As i had problems with flashing u990 H3G IRELAND i decide to try flash it with ku990 sw diplayed thats not the same model but i forced this to be flashed.
everything went ok and phone is now fully debranded and working all right

It seems that ku990 is same like u990 wich was made only for 3 networks