GSM-Forum

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   n-Box (https://forum.gsmhosting.com/vbb/f284/)
-   -   Free All About Re-Prog' Atmel And Active UFS, N-Box... (https://forum.gsmhosting.com/vbb/f284/free-all-about-re-prog-atmel-active-ufs-n-box-973981/)

trinhngoctrung 04-10-2010 22:09

Free All About Re-Prog' Atmel And Active UFS, N-Box...
 
Your Box usually error by electronic shock, SW Update fail, and lots of other reasons... In some cases, you can fix them by free SW, through USB interface, but in alots of cases, you can not, because, "the FW" of ATMEGA chip is corrupt.

To solve that, the best way (And the only way) is programing the ATMEGA8 of your box!

Todo it yourself, you need:

- Selfmade Simple AVR (You also use it to re-prog' ATMEGA128 of JAF Box too), here is the picture of LPT-AVR

http://i125.photobucket.com/albums/p...ng/AVR_ISP.gif

- Setup PonyProg (Can use to Prog' AT128 of JAF box too)

DOWNLOAD

- Connect your AVR with your Micro UFS following this:


http://i260.photobucket.com/albums/i...nghe/001-1.jpg

http://i125.photobucket.com/albums/p.../ATmel_dan.gif

- If the box is the big one, you can remove ATMEGA8, and connect it like this:


http://i260.photobucket.com/albums/i...he/AVR_LPT.jpg

- Ofcourse, you can connect it onboard following this:

http://i125.photobucket.com/albums/p...ATmel8_dai.gif

- All Steps of Programing and set fuse bits, following this Video (Sorry, I did it to support my members of my forum, so it's in our language text tips)

Video Download

- Here is the good Hex and Eeprom for UFS

DOWNLOAD

- After re-prog ATMEGA8, you must active your box, Use this tool:

DOWNLOAD

- Following this Video:


DOWNLOAD VIDEO

All Pass to Download: trinhngoctrung

All done! Now, your box is OK, with 2.6 FW. You can re-connect HWK chip and use HWK update client to update your box to get FW 2.8 and config Box <=> HWK chip! You can also use MXkey, Just let MXkey tool update your box to 2.8 easyly if you have No HWK chip!

Best Regarts!


PS/ Thanks all my friends, who help me with the SW and schematic! Thanks all people that I use the SWs, solutions from!

gsmbled 04-10-2010 22:41

is very good solution, because a lotof ufsmicro and hwkbox gpg have this problem of atmel
but i don't understand the picture PDIP, where is ine the box, and what i connect it.
and gnd you use what

trinhngoctrung 04-12-2010 06:58

Quote:

Originally Posted by gsmbled (Post 5693700)
is very good solution, because a lotof ufsmicro and hwkbox gpg have this problem of atmel
but i don't understand the picture PDIP, where is ine the box, and what i connect it.
and gnd you use what

Quote:

- If the box is the big one, you can remove ATMEGA8, and connect it like this:
"The Big one" = UFS, N-Box that have PBC like thí:

http://i260.photobucket.com/albums/i...nghe/N-Box.jpg

In that case:

Quote:

- Ofcourse, you can connect it onboard following this:
http://i125.photobucket.com/albums/p...ATmel8_dai.gif

Is It enough clear?

hackgsm 04-15-2010 01:19

program atmega 8 ufsx or micro ufsx from hwk pin ............

http://i.imagehost.org/0349/ufsx_atmega-prog.png

FEATURE GSM™ 04-15-2010 18:01

give the Password Protected File pls

spyer 04-15-2010 18:09

Quote:

Originally Posted by gsm3_zaman (Post 5717160)
give the Password Protected File pls

All Pass to Download: trinhngoctrung

hackgsm 04-15-2010 20:07

4shared.com - online file sharing and storage - download ufs3tools_c_v3.rar

vivekk 04-29-2010 16:01

Bro. i have GPG hwk box ! what are the schematics ? coz its diffrent PCB from MICRO UFS box ! as XILINIX is at the rear side ! i can not post the pcb picture ! as i dont have Good camera !

can i take out atmel ic and solder all wires on legs !then can it be programmed like this ! or it needs a programmer ? or if u can provide wiring for GPG hwk box !

moussa djamel 05-14-2010 12:00

Thank you, You have covered the subject and did not leave anything.................

rickliew 05-21-2010 06:49

after done all these,can i use the hwk latest version 2.10?

GSM TT 05-21-2010 12:11

well done man realy very well done

el-polaco 07-30-2010 02:21

Ufs pinout for atmega
 
Quote:

Originally Posted by vivekk (Post 5778287)
Bro. i have GPG hwk box ! what are the schematics ? coz its diffrent PCB from MICRO UFS box ! as XILINIX is at the rear side ! i can not post the pcb picture ! as i dont have Good camera !

can i take out atmel ic and solder all wires on legs !then can it be programmed like this ! or it needs a programmer ? or if u can provide wiring for GPG hwk box !

For repair atmega in GPG or Plastic box , use pin of hawk conector...

BR

POLACO

pcmarket 08-16-2010 23:14

any hex and e2p for 2.10? plaese i need it

tedjo13 08-30-2010 16:29

How can I extract good hex and eep from atmega ??
Any hint for this ??

leansantos 09-08-2010 14:13

please my friend ,n-box pictures and step by step, as to reprogramar and never more to give to error 1020 among others errors, since the error exactly is not of the user more yes of it team n-box.org and its deliverers who charge one I fix of these, you unite all the affiliated ones and vcendedores of the products saras revert any error, already the user not. .obrigado in case that it has a solution


All times are GMT +1. The time now is 12:15.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -

Page generated in 0.16362 seconds with 6 queries

SEO by vBSEO