nspro : déb e250 - GSM-Forum

ADDOUL0101 · 04-13-2009, 13:25

wheni wante to debloc the mobile e250, my os need the driver

SUUNNYY · 04-13-2009, 13:41

Quote:

Originally Posted by ADDOUL0101

wheni wante to debloc the mobile e250, my os need the driver

THERE IS NO NEED TO INSTALL ANY DRIVER,DOWNLOAD AND INSTALL LAST VERSION 5.1.0 FROM http://www.nsteam.org/download.html AND INSTALL,SELECT THE MODEL YOU WANT TO UNLOCK,SOFTWARE GAVE INSTRUCTIONS OF CABLE AND POWER STATUS JUST FOLLOW THE INSTRUCTIONS APPEARING LEFT LOWER SIDE OF NS PRO INTERFACE,WITH BEST REGARDS,SUUNNYY

ADDOUL0101 · 04-14-2009, 11:19

the pb for driver is resolu, but i have this message :

Entering TAT Mode...
Operation failed!

SUUNNYY · 04-14-2009, 12:51

Quote:

Originally Posted by addoul0101

the pb for driver is resolu, but i have this message :

Entering tat mode...
Operation failed!

hi friend there are 3 types of e 250 old,e250(d),e250v select right model in ns pro,if the pcb colur of your phone is blue its a e250(d) if its green then its a e250v otherwise e 250 old so gave a look and select right one and hit unlock,regards,suunnyy

ADDOUL0101 · 04-14-2009, 19:00

250 old,e250(d),e250v ========= Entering TAT Mode...
Operation failed!

SUUNNYY · 04-14-2009, 19:53

Quote:

Originally Posted by addoul0101

250 old,e250(d),e250v ========= entering tat mode...
Operation failed!

hi friend make sure that only ns pro is connected during operation,configure ns pro to port below then 10,clean phone connector,also check your cable because there is no problem with this model,retry,regards,suunnyy

ADDOUL0101 · 04-15-2009, 00:14

Always this problem with e250v,d,old:
Entering TAT Mode...
operation failed!

Elco · 04-15-2009, 07:35

Quote:

Originally Posted by ADDOUL0101

Always this problem with e250v,d,old:
Entering TAT Mode...
operation failed!

Check the cable, nspro box and phone system connector.
There is a bad connection on one of them.

04-13-2009, 13:25	#1 (permalink)
ADDOUL0101 Freak Poster Join Date: Apr 2009 Age: 40 Posts: 105 Member: 1005871 Status: Offline Thanks Meter: 1	nspro : déb e250 wheni wante to debloc the mobile e250, my os need the driver

04-15-2009, 00:14	#7 (permalink)
ADDOUL0101 Freak Poster Join Date: Apr 2009 Age: 40 Posts: 105 Member: 1005871 Status: Offline Thanks Meter: 1	problem with e250v Always this problem with e250v,d,old: Entering TAT Mode... operation failed!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
First in the world :.: repair s5600 flash boot with nspro	fypoi	NSPRO	23	11-30-2012 12:01
NsPro 1.9.3 E250	Kastas	NSPRO	8	07-02-2008 04:17
F300 vs. NsPro :-)	chip_2000	NSPRO	12	05-23-2008 17:57
..:=( E250 and LG8210 )=:..	LePilami	UST Pro II	2	06-08-2007 21:32
NSPro 2.05 and E250	fortheadingley	NSPRO	24	04-07-2007 13:28

04-14-2009, 11:19	#3 (permalink)
ADDOUL0101 Freak Poster Join Date: Apr 2009 Age: 40 Posts: 105 Member: 1005871 Status: Offline Thanks Meter: 1	the pb for driver is resolu, but i have this message : Entering TAT Mode... Operation failed!

04-14-2009, 19:00	#5 (permalink)
ADDOUL0101 Freak Poster Join Date: Apr 2009 Age: 40 Posts: 105 Member: 1005871 Status: Offline Thanks Meter: 1	250 old,e250(d),e250v ========= Entering TAT Mode... Operation failed!