nspro driver problem! - GSM-Forum

espnaci · 06-26-2010, 18:13

I have tried installing and reinstalling my new nspro box, but I always get the same error that the box is not detected I am running xp sp3. so after searching the forum I found out that perhaps my drivers are not correctly installed. I have tried to manually install the drivers but I cant since nspro converter nor nspro box under usb controller. What could be the problem?

Elco · 06-27-2010, 13:52

Right click on My computer->Properties->Hardware->Driver Signing
Select "Ignore" and "Make this system default" then click OK

espnaci · 06-28-2010, 17:41

Hello Elco,

i did what you said but my settings where correct it was already set to ignore and my pc still cat detect my box.

Elco · 06-28-2010, 23:02

If the box is not detected at all, it might be a bad USb cable, or a hardware damage on nspro USb IN connector.

espnaci · 06-29-2010, 02:44

I have fixed the problem apperently it had something to do with my sp3 install.

redevip · 11-04-2010, 20:40

Quote:

Originally Posted by Elco

Select "Ignore" and "Make this system default" then click OK

this was my problem aparently

thanks Elco

06-26-2010, 18:13	#1 (permalink)
espnaci Junior Member Join Date: Jun 2010 Posts: 6 Member: 1331949 Status: Offline Thanks Meter: 0	nspro driver problem! I have tried installing and reinstalling my new nspro box, but I always get the same error that the box is not detected I am running xp sp3. so after searching the forum I found out that perhaps my drivers are not correctly installed. I have tried to manually install the drivers but I cant since nspro converter nor nspro box under usb controller. What could be the problem?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
"Deskey Device driver not found" ?? Please help	DivAdonis	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	06-08-2017 13:21
DES key Driver	black	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	02-08-2014 04:50
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

06-27-2010, 13:52	#2 (permalink)
Elco No Life Poster Join Date: Dec 2002 Location: Romania Posts: 10,018 Member: 19254 Status: Offline Sonork: 100.72990 Thanks Meter: 25,395	Right click on My computer->Properties->Hardware->Driver Signing Select "Ignore" and "Make this system default" then click OK

06-28-2010, 17:41	#3 (permalink)
espnaci Junior Member Join Date: Jun 2010 Posts: 6 Member: 1331949 Status: Offline Thanks Meter: 0	Hello Elco, i did what you said but my settings where correct it was already set to ignore and my pc still cat detect my box.

06-28-2010, 23:02	#4 (permalink)
Elco No Life Poster Join Date: Dec 2002 Location: Romania Posts: 10,018 Member: 19254 Status: Offline Sonork: 100.72990 Thanks Meter: 25,395	If the box is not detected at all, it might be a bad USb cable, or a hardware damage on nspro USb IN connector.

06-29-2010, 02:44	#5 (permalink)
espnaci Junior Member Join Date: Jun 2010 Posts: 6 Member: 1331949 Status: Offline Thanks Meter: 0	I have fixed the problem apperently it had something to do with my sp3 install.