"philips semiconductors full speed dfu driver" - GSM-Forum

tito millo · 01-11-2008, 18:35

i´m trying to flash a G600 to change the language and i get the following error
¨Powering on mobile...
BOOT_CREQ Error

Press BACK to continue...¨

but while the phone is trying to powerup windows detects the following device ¨philips semiconductors full speed dfu driver¨and it´s looking for it´s drivers, i have searched all over and these drivers are no where to be found.

i´m using nspro 3.7.3

any ideas??

Elco · 01-12-2008, 01:09

Leave the phone connected to cable, puth the battery on the phone.
Power on the phone, then power off the phone, remove battery and try again.
Make sure that Nspro drivers are correctly installed and autoignition is working on your NsPro box.
More info about autoignition and driver problems here: http://www.nsdongle.com/forum/index....ic,2199.0.html

tito millo · 01-12-2008, 17:16

i´ve tried that and still doesn´t work, i know the cable is good becasue i´ve used it with other phones.

I have 2 NSPro boxes, in one of them the blue light does not turn on, on the other one it does turn on but when i click on write to flash the phone the blue light goes off.

I´ve reinstalled the drivers several times following the tutorial.

I also have another problem. i´ve installed the NSPro software on a couple of other computers, those computers had a fresh windows install, when i run the NSpro software it does run but after i choose the phone model number to work with and after i click on one of the opions read info for example the program closes automatically, any idea why?? i´ve reinstalled the drivers as well on these other machines following the tutorial but the results were the same, please help¡¡

Elco · 01-12-2008, 23:52

That may be a power problem caused by bad USB cable that connect NsPro Box to PC.

tito millo · 01-14-2008, 16:27

I have trien many different USB Cables and i get the same results.

Using the Samsung Rocker dongle i'm able to put the phone in TAT mode, but Samsung Rocker dongle does not support flashing.

shaak28 · 04-30-2008, 13:27

nspro is too much buggy for flashing, if it shows different types of error while trying to flash d900,u600,u700,j700 and g600 , its nspro fault but elco is not in a mode to accept this. I flashed many nspro rejected phones many times on first try on ufs hwk.

f164 · 04-30-2008, 21:19

Quote:

Originally Posted by shaak28

nspro is too much buggy for flashing, if it shows different types of error while trying to flash d900,u600,u700,j700 and g600 , its nspro fault but elco is not in a mode to accept this. I flashed many nspro rejected phones many times on first try on ufs hwk.

that's true brother ( i don't know why ) same story with e250 fail to flash it using ns pro but with ufs success at the first try (elco what's the matter)

beerfoote1 · 05-13-2008, 23:15

Quote:

Originally Posted by f164

that's true brother ( i don't know why ) same story with e250 fail to flash it using ns pro but with ufs success at the first try (elco what's the matter)

Elco we await solutions please SIR...... I am having same problem. Please advise

gambitjam · 07-03-2008, 21:57

The topic is entering tatmode while shows PHILIPS SEMICONDUCTORS. Why do you want to bring in another case which i presume already posted somewhere.
Pls let him attend to the problem on topic.

Nadeem ahmed · 10-10-2008, 14:47

when it asks for this driver, ignore it, on nspro when flashing or unlock and giving you an error, try again and keep hold on power button untill process starts, i have this same problem, but ignore the driver message just keep hold on the power button.

RASHEDBD57 · 05-31-2010, 07:25

philips semiconductors full speed dfu driver"
NEED SIER..................................

arantima · 06-25-2010, 08:47

here are rare these driver who cried

Philips_semiconductors_full_speed_dfu.rar - 4shared.com - online file sharing and storage - download

mahfuesh · 01-15-2012, 22:16

Quote:

Originally Posted by arantima

here are rare these driver who cried

Philips_semiconductors_full_speed_dfu.rar - 4shared.com - online file sharing and storage - download

............................?????????????///

01-11-2008, 18:35	#1 (permalink)
tito millo No Life Poster Join Date: Nov 2006 Location: Where money is made Age: 33 Posts: 3,045 Member: 390642 Status: Offline Sonork: 100.1573430 Thanks Meter: 2,476	"philips semiconductors full speed dfu driver" i´m trying to flash a G600 to change the language and i get the following error ¨Powering on mobile... BOOT_CREQ Error Press BACK to continue...¨ but while the phone is trying to powerup windows detects the following device ¨philips semiconductors full speed dfu driver¨and it´s looking for it´s drivers, i have searched all over and these drivers are no where to be found. i´m using nspro 3.7.3 any ideas??

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
nxp semiconductors full speed DFU solution	Copernico	Samsung Flashers, Software, Firmware.	8	01-23-2013 04:43
"Philips Semiconductors - Full Speed - DFU"	mobile-phone-service	NSPRO	8	12-16-2009 22:55
philips semiconductors full speed dfu driver	rajinder1978	UST Pro II	1	12-16-2009 22:54
NXP semiconductors - full speed _DFU drivers ?	johansel	NSPRO	4	06-12-2008 01:43
J700 flashing problem. NXP Semiconductors-Full Speed DFX???	shaak28	NSPRO	2	04-20-2008 00:45

01-12-2008, 01:09	#2 (permalink)
Elco No Life Poster Join Date: Dec 2002 Location: Romania Posts: 10,018 Member: 19254 Status: Offline Sonork: 100.72990 Thanks Meter: 25,395	Leave the phone connected to cable, puth the battery on the phone. Power on the phone, then power off the phone, remove battery and try again. Make sure that Nspro drivers are correctly installed and autoignition is working on your NsPro box. More info about autoignition and driver problems here: http://www.nsdongle.com/forum/index....ic,2199.0.html

01-12-2008, 17:16	#3 (permalink)
tito millo No Life Poster Join Date: Nov 2006 Location: Where money is made Age: 33 Posts: 3,045 Member: 390642 Status: Offline Sonork: 100.1573430 Thanks Meter: 2,476	i´ve tried that and still doesn´t work, i know the cable is good becasue i´ve used it with other phones. I have 2 NSPro boxes, in one of them the blue light does not turn on, on the other one it does turn on but when i click on write to flash the phone the blue light goes off. I´ve reinstalled the drivers several times following the tutorial. I also have another problem. i´ve installed the NSPro software on a couple of other computers, those computers had a fresh windows install, when i run the NSpro software it does run but after i choose the phone model number to work with and after i click on one of the opions read info for example the program closes automatically, any idea why?? i´ve reinstalled the drivers as well on these other machines following the tutorial but the results were the same, please help¡¡

01-12-2008, 23:52	#4 (permalink)
Elco No Life Poster Join Date: Dec 2002 Location: Romania Posts: 10,018 Member: 19254 Status: Offline Sonork: 100.72990 Thanks Meter: 25,395	That may be a power problem caused by bad USB cable that connect NsPro Box to PC.

01-14-2008, 16:27	#5 (permalink)
tito millo No Life Poster Join Date: Nov 2006 Location: Where money is made Age: 33 Posts: 3,045 Member: 390642 Status: Offline Sonork: 100.1573430 Thanks Meter: 2,476	I have trien many different USB Cables and i get the same results. Using the Samsung Rocker dongle i'm able to put the phone in TAT mode, but Samsung Rocker dongle does not support flashing.

04-30-2008, 13:27	#6 (permalink)
shaak28 Freak Poster Join Date: Aug 2006 Posts: 148 Member: 322957 Status: Offline Thanks Meter: 6	nspro is too much buggy for flashing, if it shows different types of error while trying to flash d900,u600,u700,j700 and g600 , its nspro fault but elco is not in a mode to accept this. I flashed many nspro rejected phones many times on first try on ufs hwk.

07-03-2008, 21:57	#9 (permalink)
gambitjam No Life Poster Join Date: Feb 2005 Location: HOME OF PEACE Posts: 661 Member: 113732 Status: Offline Thanks Meter: 90	The topic is entering tatmode while shows PHILIPS SEMICONDUCTORS. Why do you want to bring in another case which i presume already posted somewhere. Pls let him attend to the problem on topic.

10-10-2008, 14:47	#10 (permalink)
Nadeem ahmed Freak Poster Join Date: Mar 2007 Age: 33 Posts: 109 Member: 474191 Status: Offline Thanks Meter: 9	when it asks for this driver, ignore it, on nspro when flashing or unlock and giving you an error, try again and keep hold on power button untill process starts, i have this same problem, but ignore the driver message just keep hold on the power button.

05-31-2010, 07:25	#11 (permalink)
RASHEDBD57 Junior Member Join Date: May 2010 Posts: 37 Member: 1298600 Status: Offline Sonork: 12 Thanks Meter: 17	philips semiconductors full speed dfu driver" NEED SIER..................................

06-25-2010, 08:47	#12 (permalink)
arantima Junior Member Join Date: Jul 2006 Posts: 34 Member: 319731 Status: Offline Thanks Meter: 14	here are rare these driver who cried Philips_semiconductors_full_speed_dfu.rar - 4shared.com - online file sharing and storage - download