ZV40 unknown device when connect with modified cable - GSM-Forum

midou01 · 01-19-2007, 16:15

i have tried to unlock 2 ZV40 and i used schematics posted here by elco to modify my d800 cable but when i connect the rj45 to nspro port the phone shows that there are a pc cable connected to phone but on computer i have a mesage "unknown device detected" and i have all the drivers installed. Anyone can help me please????

Elco · 01-19-2007, 16:34

Swap D+ and D- lines and the phone will be detected.

midou01 · 01-19-2007, 18:04

I swapped the D+ and D- lines and now the pc detect "Samsung UMTS ..." but i have the "usb hub exceed..." exceed message. I use the modified cable so how could it be????

midou01 · 01-19-2007, 20:17

Now everything is fine, i solved my problem by mading the adapter following the schematic posted on the support area, today i unlocked my 2 ZV40 and 1 Z710 even nspro said that the unlocking was faild but when i powered on the Z710 it was unlocked

thanks elco

midou01 · 01-21-2007, 13:01

Now it is the Z560 turn to be unlocked with NSPRO in really 3 seconds!!!! GOOD JOB ELCO!!!

to be continued...
PS. For all persons who have proble to unlock new Z series just make the adaptator shown in support area and everything will be fine!!!

wazim187 · 01-21-2007, 18:21

hi i have made a cable following elco's schematic, but when i connect my computer does not detect modem drivers. can any1 help

midou01 · 01-21-2007, 21:20

in this case swap the D+ and D- on your cable; it consist in swapping pin 16 with pin 17 on phone connector)

Tubal Cain · 01-22-2007, 05:14

Quote:

Originally Posted by Yawacom

in this case swap the D+ and D- on your cable; it consist in swapping pin 16 with pin 17 on phone connector)

m8 do i also need to remove the diode and reisitor connected at pins 13 14 and 15... help pls...

midou01 · 01-22-2007, 20:26

no m8, if you made the adaptator don't need to remove diode and resistor

Tubal Cain · 01-23-2007, 06:19

Quote:

Originally Posted by Yawacom

no m8, if you made the adaptator don't need to remove diode and resistor

immediate response very well appreciated and thanks very much for help..

regards

luskao · 01-23-2007, 13:17

Yes, I unlocked 8 Z230 in a minute all of them. The flashing procedure was fast but the cable doesn't fit so fast in the phones

BR and good job Elco

Luskao

01-19-2007, 16:15	#1 (permalink)
midou01 No Life Poster Join Date: Oct 2003 Location: Tunisia Age: 43 Posts: 2,158 Member: 40632 Status: Offline Sonork: 98231 Thanks Meter: 1,658	ZV40 unknown device when connect with modified cable i have tried to unlock 2 ZV40 and i used schematics posted here by elco to modify my d800 cable but when i connect the rj45 to nspro port the phone shows that there are a pc cable connected to phone but on computer i have a mesage "unknown device detected" and i have all the drivers installed. Anyone can help me please????

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dreambox soft Freeze when connect via DCU60 cable	kpotin	DreamBox	3	02-14-2010 02:26
samsung c140 2pcs unlock done via free supware with modify cable	ART_74	Samsung Flashers, Software, Firmware.	0	05-07-2009 07:10
BB5 phones powers only with modified cable problem	skydreas	Nokia Base Band 5 ( BB-5 )	0	04-12-2007 09:43
Nokia 3610 show not charging when connect with charger	TechPhone	Nokia Hardware & Hardware Repair	2	01-27-2004 20:29

01-19-2007, 16:34	#2 (permalink)
Elco No Life Poster Join Date: Dec 2002 Location: Romania Posts: 10,018 Member: 19254 Status: Offline Sonork: 100.72990 Thanks Meter: 25,395	Swap D+ and D- lines and the phone will be detected.

01-19-2007, 18:04	#3 (permalink)
midou01 No Life Poster Join Date: Oct 2003 Location: Tunisia Age: 43 Posts: 2,158 Member: 40632 Status: Offline Sonork: 98231 Thanks Meter: 1,658	I swapped the D+ and D- lines and now the pc detect "Samsung UMTS ..." but i have the "usb hub exceed..." exceed message. I use the modified cable so how could it be????

01-19-2007, 20:17	#4 (permalink)
midou01 No Life Poster Join Date: Oct 2003 Location: Tunisia Age: 43 Posts: 2,158 Member: 40632 Status: Offline Sonork: 98231 Thanks Meter: 1,658	Now everything is fine, i solved my problem by mading the adapter following the schematic posted on the support area, today i unlocked my 2 ZV40 and 1 Z710 even nspro said that the unlocking was faild but when i powered on the Z710 it was unlocked thanks elco

01-21-2007, 13:01	#5 (permalink)
midou01 No Life Poster Join Date: Oct 2003 Location: Tunisia Age: 43 Posts: 2,158 Member: 40632 Status: Offline Sonork: 98231 Thanks Meter: 1,658	Now it is the Z560 turn to be unlocked with NSPRO in really 3 seconds!!!! GOOD JOB ELCO!!! to be continued... PS. For all persons who have proble to unlock new Z series just make the adaptator shown in support area and everything will be fine!!!

01-21-2007, 18:21	#6 (permalink)
wazim187 Freak Poster Join Date: Oct 2004 Location: MX-KEY is the BEST NOKIA TOOL Age: 44 Posts: 137 Member: 87636 Status: Offline Thanks Meter: 8	hi i have made a cable following elco's schematic, but when i connect my computer does not detect modem drivers. can any1 help

01-21-2007, 21:20	#7 (permalink)
midou01 No Life Poster Join Date: Oct 2003 Location: Tunisia Age: 43 Posts: 2,158 Member: 40632 Status: Offline Sonork: 98231 Thanks Meter: 1,658	in this case swap the D+ and D- on your cable; it consist in swapping pin 16 with pin 17 on phone connector)

01-22-2007, 20:26	#9 (permalink)
midou01 No Life Poster Join Date: Oct 2003 Location: Tunisia Age: 43 Posts: 2,158 Member: 40632 Status: Offline Sonork: 98231 Thanks Meter: 1,658	no m8, if you made the adaptator don't need to remove diode and resistor

01-23-2007, 13:17	#11 (permalink)
luskao Product Supporter Join Date: Sep 2004 Age: 39 Posts: 5,993 Member: 81703 Status: Offline Thanks Meter: 1,332	Yes, I unlocked 8 Z230 in a minute all of them. The flashing procedure was fast but the cable doesn't fit so fast in the phones BR and good job Elco Luskao