New Phoenix Service Software 2005.36.7.112 download here!

[qwerthj]

http://rapidshare.de/files/6708731/p...part1.rar.html
http://rapidshare.de/files/6710176/p...part2.rar.html

[Royslade]

Thanks for sharing...

BR Roy

[Mobile2001]

Thanks for the up.

Regards

[zulea]

Hi,

Phoenix_service_sw_2005_20_13_104_upd is available now in PBB Support Area.
Tomorrow will be ready also new PBB online update (firmware version 0B) who will work with this version.
From my informations, this new version of Phoenix solve flashing problem on Nokia phones with new flash IC chip.

Best regards,
Zulea

[Friendship]

Thank m8 that is agreat job.

[Friendship]

Originally Posted by zulea

Hi,

Phoenix_service_sw_2005_20_13_104_upd is available now in PBB Support Area.
Tomorrow will be ready also new PBB online update (firmware version 0B) who will work with this version.
From my informations, this new version of Phoenix solve flashing problem on Nokia phones with new flash IC chip.

Best regards,
Zulea

Finally you come out .
Good Job Zulea.Thanks alot.

[zulea]

Hi,

Sorry my mistake. I not see this is new version. This will be available also in support area tomorrow. Also have reports that this version work well with current PBB firmware (version 0A). Here is what is new in this Phoenix release:

NEW MULTI PROTOCOL PHOENIX SERVICE SOFTWARE VERSION 2005.36.7.112
Version history:
Version 1 24.10.05 Initial version
New multi protocol (including support for CDMA, GSM, TDMA and WCDMA)
Phoenix Service Software version 2005.36.7.112 has been released.
If you have Phoenix version 2004.24.7.55 or older it must be uninstalled
before this new version 2005.36.7.112 is installed.
This Phoenix Service Software installation package includes following SW
components:
- Phoenix Service Software 2005.36.7.112
- DK2 Dongle Driver v6.00.0.134
- DKU-2 USB Driver 05.02.154
- f*l*s-4S Dongle Driver v2.07.03
- Flash Update files for f*l*s-4S and f*p*s-8* v3.33.002
- Software package for f*p*s-10 v 1.9.1
- Software package for f*p*s-11 v 1.00.029.0
- Faultlog and Archive & Send programs for repair data reporting
Recommended PC HW requirements:
- Computer Processor: Pentium 700 MHz or higher
- RAM 256 MB
- Needed disk space 100-200 MB
Supported Operating Systems:
- Windows 2000 Service Pack 3 or higher
- Windows XP Service Pack 1 or higher
During installation a Dongle must be attached to the parallel port of your
computer and when installing Phoenix into Win2000 or XP you must have
admin rights locally.
For using the Phoenix in Win2000 or XP, user must have power user rights.

After installing Phoenix Service Software version 2005.36.7.112, please
install latest product specific data package; do not use old data
packages.
Supported phone models (please see APPENDIX I)
Changes/improvements made to from v 2005.20.7.98 to v 2005.36.7.112:
- Support for RM-10, RM-38, RM-43, RM-49, RM-70, RM-89, RM-111, RM-
127, RM-158 and RM-173 products added.
- New f*l*s-4S Driver v 2.07.03
- New Flash Update Package v 3.33.002
- RF loss table for autotuning updated for new products.
- Audio test function improved for RM-43
- New audio control UI for SU-18
- Product menu for SU-18 is improved.
- The Certificate Restore supports the SU-18.
- Second display test support is added for RM-8 and RM-47.
- Additional display and keyboard test functions for RH-37, RM-30, RM-76,
RM-17, RH-12, RM-36, RM-42 and RH-73 are added.
- Content package is yet again successfully extracted and correct amount
of licences removed from f*l*s-4S while flashing RH-37, RM-30, RM-76
and RM-17.
- Support for HDD Log File with RM-43 is added.
- New user interface for new datapackage formats are implemented.
- User Interface and functionality for f*p*s-11 has been improved.
- NAND flash support has been added into f*p*s-11
- “Error loading component” message while starting f*p*s-11 is fixed.
- “Tx Agc tuning” menu is corrected.
- “Simlock status” menu is added for BB 5 phones.
- TX Power Level Tuning(PA mode) is improved for RH-53, RH-54, RM-4,
RM-5, RH-59, RH-60, RH-26 and RH-68.
- "can't restore fm radio data correctly" problem with RH-12 is fixed.
- The Smart Card activator UI shows the status of the card and the
remaining licenses.
- PRI settings is saved and restored during CDMA flash operations
- CDMA refurbish- and warranty transfer-function is improved
- Smart Card Pin code is prompted from user when f*p*s-10 Advanced
flashing is performed for CDMA phones. If a wrong PIN code is entered,
advanced flash needs to be restarted in order to enter the PIN code
again.
- CDMA flashing support added for RM-97.
- RF AGC Status windows in CDMA are corrected.
- Added CARE Quick Test feature for AI2 GPS control component in
CDMA.
- Label printing menu changes implemented and common Label Print used
with all CDMA products.
- Problem with ESN- text and barcode printing to label for CDMA phones is

- Updated GPS Support for CDMA Phones
- “Phone Settings” feature now appears in the CDMA menu
Known limitations/errors:
- PKD-1 Dongles with 5 digit serial numbers do not work when connected
to parallel port with the f*p*s-8* Flash Prommer. Phoenix does not
recognize the dongle and Phoenix will not start. The solution is to change
your dongle to a new one with 6-digit serial number, please contact your
regional technical support for help.
- The parallel port in some IBM Netvista computers may cause problems
when using the f*l*s-4S. This is because the rise time for the strobe is
much longer than for any other of the pins on the port, problem has to do
with the parallel port HW.
- GSM / WCDMA Data package network use (Phoenix on local machine,
data package on a shared network drive) not fully supported
- If autotuning for BB5 phones fails with “RX-AM suppression in GSM1900”
please use latest minor or major product data package.
- If manual “TX power level tuning” did not work with BB5 phones, please
use latest minor or major product data packages.
- POS flashing with RH-18 and RH-75 is not working on a WIN2000
system. Workaround: Please uninstall f*l*s-4S driver 2.07.03 and install
previous version 2.06.
- Smart Card Detection problems with f*p*s-11
- “UI controls” is disabled in “Bluetooth Locals” feature.
- “PSN Write” causes ‘Error loading component’ when PKD-1i or PKD-1NS
is used with CDMA
- CDMA phones can’t be flashed with f*p*s-10 and f*p*s-11
- The Phone Settings feature does not appear in the CDMA menu
- Intermittent problem when refurbishing USB capable phones. The tool will
give a false positive confirmation stating that refurbish is done within 5
minutes or less. Typical refurbish process takes about 10-15 minutes.
Recommended workaround solution: re-try the refurbish process.
- Content package may intermittently fail to be loaded. Recommended
workaround solution: re-try the refurbish process.
- MIN and MDN do not get restored when RM-66 phone is loaded with ERI.
Needed equipment for software update:
- Phoenix Service Software version 2005.36.7.112 (or later), which
includes all needed drivers and flash support files
- Latest phone model specific Product Data Package or Flash Bundle
- Flash Update package for f*p*s-8/f*l*s-4 (v 3.33.002 included in Phoenix
package)
- JBV-1 Software Update v 18 or later (not valid for JBV-1 RoHS compliant)
- Parallel Port Driver for f*p*s-8, if you experience slow file transfer speed
via LPT port
- PKD-1 Dongle & Activated Flash Prommer f*p*s-8 or
- f*l*s-4S POS Flash Dongle
- Programming devices for updating the phone software
- Product specific service devices
Note:
- A complete Phoenix service SW installation package will always
include the latest available drivers and flash update files
- Please use separate driver of flash support file installation packages
only, if updates occur between complete Phoenix releases
How to install new Phoenix 2005.36.7.112
1. Download phoenix_service_sw_2005_36_7_112.exe – application file
from NOL to your computer (e.g. C:\TEMP)
2. Close all other programs
3. Run phoenix_service_sw_2005_36_112.exe and follow instructions on
the screen to install Phoenix Service Software.
4. If you are prompted to update any existing driver or file versions, select
“yes”
5. Depending on the operating system PC may require rebooting
6. Allow Windows to register Phoenix components
7. Open Phoenix and update your prommer with the latest software included
in this installation package
Use the latest available product specific data packages or flash bundles with
new multi protocol Phoenix.

Best regards,
Zulea

P.S. Many thanks to Roy for this info.

[josetolo_jr]

Very good update Sir. I will try to update my PBB to v0A. But my problem is my download was already exhausted. Please help me to reset my account to be able to download again. More power to you.

My Best Regards,
josetolo_jr

[~AKSingh~]

THANX MR.ZULEA

FOR A NICE UPDATE
CAN U PLEASE GUIDE ME FOR LANGUAGE UPLOADING IN NOKIA CDMA HANDSETS BY PBB,
WAITING FOR UR REPLY EAGERLY !!!

WBR
singhinfosys

[blaiseid]

Originally Posted by zulea

Hi,

Phoenix_service_sw_2005_20_13_104_upd is available now in PBB Support Area.
Tomorrow will be ready also new PBB online update (firmware version 0B) who will work with this version.
From my informations, this new version of Phoenix solve flashing problem on Nokia phones with new flash IC chip.

Best regards,
Zulea

You mean I cant use it with the old version of PBB before 0A???

[andr3as]

Originally Posted by zulea

Hi,
Sorry my mistake. I not see this is new version. This will be available also in support area tomorrow. Also have reports that this version work well with current PBB firmware (version 0A). Here is what is new in this Phoenix release:
NEW MULTI PROTOCOL PHOENIX SERVICE SOFTWARE VERSION 2005.36.7.112

@blaiseid Do you read all of the posts?

[zulea]

Hi,

Phoenix Service Software version 2005.36.7.112 is now in PBB Support Area. Just download and enjoy it, flash/repair all new Intel based chip phones like 3220, 7260, ... Works well with PBB firmware version 0A or upper. Also online update server for PBB owners is up and running well

Best regards,
Zulea

[nofear197979]

Likns Not Working With Me Plz Can U Upload It Another Time?

[vule]

I already have repaired 3220 with new ST and new MCUID using phoenix_service_sw_2005_20_7_98... This phone went dead on tornado and now back again...

BR

Vule

[plutonn]

The link phoenix...part 2. have too many downloads!!


[email protected]


bye