2008 flash error - GSM-Forum

sunil kumar · 06-04-2010, 13:28

i have NKTL 2008 FLASHING ERROR

COM4 [VCP0] selected
module v3.07
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: reset settings ("format ffs")
ffs/eeprom backup enabled, it may takes several minutes !
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001

F03:0002
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
====> Initialize ...
detecting chip #00 in region #00...
flash: 00E580F000E580:00E58000000000
flash: 00E580F000E580:00E58000000000
number of flash chip/regions detected: 00/01
flash chip is unknown or damaged, operation aborted.

Fault reasons:
1. flash chip is damaged: replace or resolder/reball flash chip
2. hardware is damaged: check hardware, water inside etc.
3. unknown hardware: set "Advanced chip detection method" box [checked] and try again
4. wrong model selection, try 'NAND' selection
Initialize Fail
Finished, time used: 19 sec
Remove/Install battery now !

InfinityHelp · 06-04-2010, 20:47

hello!

what problem with this phone?

sunil kumar · 06-05-2010, 10:21

phone is dead( not power on)

InfinityHelp · 06-07-2010, 10:34

hello!

as you can see- flash IC was not detected properly.
try to resolder it and at least heat it

if this will not help- change flash IC to new one

r-jcomm · 06-07-2010, 10:45

this is main cpu mt6225 problem change mt6225 and flash again

InfinityHelp · 06-07-2010, 11:15

hello!

i would advice to start from flash IC heating

06-04-2010, 13:28	#1 (permalink)
sunil kumar No Life Poster Join Date: Jul 2004 Location: .:INDIAN:. Posts: 790 Member: 75838 Status: Offline Thanks Meter: 67	2008 flash error i have NKTL 2008 FLASHING ERROR COM4 [VCP0] selected module v3.07 Device: Autodetect 6205-6227 NOR Checking data, wait... advanced flash detection disabled Action: reset settings ("format ffs") ffs/eeprom backup enabled, it may takes several minutes ! ====> Boot ... Press and HOLD Power button now ! 19200 fixed Connecting, wait... Initializing [6225:8A05:8A00]... CPU: MT6225 high speed boot On chip: 0001F03:0002 status: FF boot packet size: 0400 Release Power button now ! Boot Done ====> Initialize ... detecting chip #00 in region #00... flash: 00E580F000E580:00E58000000000 flash: 00E580F000E580:00E58000000000 number of flash chip/regions detected: 00/01 flash chip is unknown or damaged, operation aborted. Fault reasons: 1. flash chip is damaged: replace or resolder/reball flash chip 2. hardware is damaged: check hardware, water inside etc. 3. unknown hardware: set "Advanced chip detection method" box [checked] and try again 4. wrong model selection, try 'NAND' selection Initialize Fail Finished, time used: 19 sec Remove/Install battery now !

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
need to flash 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	08-16-2019 19:37
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
5110 flash new software , need help	steve	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	01-03-2015 05:41
where to find a working program all they have some errors ??	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	12-12-2012 13:26
error (1002) simlock3.dll winopen	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	08-28-1999 15:57

06-04-2010, 20:47	#2 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! what problem with this phone?

06-05-2010, 10:21	#3 (permalink)
sunil kumar No Life Poster Join Date: Jul 2004 Location: .:INDIAN:. Posts: 790 Member: 75838 Status: Offline Thanks Meter: 67	phone is dead( not power on)

06-07-2010, 10:34	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! as you can see- flash IC was not detected properly. try to resolder it and at least heat it if this will not help- change flash IC to new one

06-07-2010, 10:45	#5 (permalink)
r-jcomm No Life Poster Join Date: Oct 2007 Location: pakistan Posts: 1,520 Member: 601913 Status: Offline Sonork: 100.1597350 Thanks Meter: 658	this is main cpu mt6225 problem change mt6225 and flash again

06-07-2010, 11:15	#6 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! i would advice to start from flash IC heating