Auto PinFinder Power Problem - GSM-Forum

dannyogolo · 03-14-2008, 17:52

This box seems ok to me, but as with all boxes, there are a few phones that it doesnt work ok.
There are a few China phones that it cannot power. That is to say these phones comes up with battery, but not with pinfinder power cables.
Its not a matter of connecting the cables correctly, the cables are always well connected (the batteries have the "+" and "-" indicators and its almost impossible to mistake them. Also the indicator red light behind the pin finder remains on while i try to power phone (showing that the polarity is correct).

Maybe support should look at making it work with phone battery as well, or is there a way out ?

**InfinitySupport** · 03-14-2008, 18:21

Please, download latest PinFinder manual: http://www.infinity-box.biz/download..._PinFinder.pdf
Please, see page 18: Automatic pinout detection: Troubleshooting
I hope you can solve at least 99% of possible problems (especially with 8, 12, 14, 15 pins cables) with this instruction.

One more link: http://www./showthread.php?t=512662

targettelecom · 03-14-2008, 18:23

this finder dont need to power on mobile ,its enugh give power for cpu and power ic to be can serach pinout .only when you make serach by finder need to stay press power key mobile untill find him.
if not find that mobile so your mobile maybe not mtk .

InfinityHelp · 03-14-2008, 22:13

hello!

some uniboxes have very small output voltage on pin1.
Also 0,7 volts is dropping on transistor which swith power to phone.
so at the end we get voltages below 3,7 volts which is not enough to power On phone
if you have on pinfinder output voltage below 3,7v- please modify your unibox
there must be diode removed and set shortcut.
Where is located this diode you can find in pin finder user manual in troubleshooting section

navin71 · 03-28-2008, 10:04

Quote:

Originally Posted by InfinitySupport

Please, download latest PinFinder manual: http://www.infinity-box.biz/download..._PinFinder.pdf
Please, see page 18: Automatic pinout detection: Troubleshooting
I hope you can solve at least 99% of possible problems (especially with 8, 12, 14, 15 pins cables) with this instruction.

One more link: http://www./showthread.php?t=512662

sir i just buy an infinity auto pin finder box can u please guide me how to use this (is there any installation cd come with this box) i have infinity box too
thanks

**InfinitySupport** · 03-28-2008, 11:09

Quote:

Originally Posted by navin71

sir i just buy an infinity auto pin finder box can u please guide me how to use this (is there any installation cd come with this box) i have infinity box too
thanks

Hello,

Information is here: http://www.infinity-box.biz/index.ph...infinder&lg=en

Read manual and pictures here: http://www.infinity-box.biz/download..._PinFinder.pdf

See video here: http://www.infinity-box.biz/download...nder_video.rar

navin71 · 03-29-2008, 17:54

sir i have connected auto pinfinder to the pc with infinity box but while connecting it shows error like this
dongle is not activated for current software module
curent dongle activation lavel 0001
required dongle activation lavel 0011
download lattest dongle manager from support area
but when connecting through dongle manager it shows like this:-
----------Process started:10:17:20 PM----------
Locating Emeralda server...
Emeralda server#1 address found.
Connecting to Emeralda server#1...
Server connection successfully established.
S/N: *********Firmware: *****
Authenticating on server...
Authentication successfull.
Checking upgrade client version...
Your upgrade client is up-to-date.
Checking Dongle Identification...
Dongle Identification checked.
Activating module...
Module check error: Server reported error:[0044] Module S/N is already registered. Don't try more !

InfinityHelp · 03-29-2008, 21:01

hello!

need same log file but with full dongle detales to mailbox: [email protected]

mansi · 03-29-2008, 22:14

@dannyogolo
maybe your phone is not MTK based, maybe its spreadtrum or something else. [which you cant auto detect pinouts] with standard cables come with pinout finder.
one small advice: open phone and check CPU type [info is writen on cpu] if its MTK or not.
BR
Mansi

navin71 · 03-30-2008, 18:30

Quote:

Originally Posted by InfinityHelp

hello!

need same log file but with full dongle detales to mailbox: [email protected]

Thanksssssssssssssssssssssssssssssssssssssssss PIN FINDER IS ACTIVATED
THE GREAT SUPPORT I EVER SEEN
THANKS AGAIN INFINITY TEAM
q.:- can rx tx can be find out from dead set ?
q;- is it necessary to connect +ve and -tve wire (mean can we used battery instead of wire)

::gsmcoder:: · 03-30-2008, 18:39

to me, pinout finder usage is not traumatic..................

InfinityHelp · 03-30-2008, 19:37

hello mr. navin71!

please read user manual, there is all questins answered:
http://www.infinity-box.biz/download..._PinFinder.pdf

Faisal_Computer · 03-31-2008, 05:41

One Qua.

when i try to connect mobile with BOX power its works fine with 80% mobiles and when i insert bettery or try to use Power Supply ( not from Box ) its gave this

software version: 1.06
cable type: 1x8 (L8A)
platform: MT6205, MT6217-MT6228
searching adapter at COM7...
adapter found, version: 2000
pins: 8, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
error: boot initialization step-2 failed: A0
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
failed to detect pins
time required: 28 sec
Power Off !

so is this mean that we must use power from box ?

and also some mobile can't power up even pinout finder find pins for example 2 or 3 days ago i got Lg Kg200 pinout finder detect pins ( power from BOX ) and i need to rebuild IMEI on power from box its can flash but when i try to rebuild imei mobile not powering up can you advice me how to solve this type of problems , on the box +tv i got 5 volts and works fine just i got these type of problems

Br

Faisal_Computer

asad_nomy7 · 03-31-2008, 06:05

bro faisal i think the power cable from the box work as GND pin also.and when we connect it other power source its not have GND pin then not detect RX/TX.

milankumardoshi · 03-31-2008, 06:58

sir output#2 of pinfider has rj45 but the power terminal was given with 10 pin jack with 10 wires inside does it cause some problem.i get output 5 v

03-14-2008, 17:52	#1 (permalink)
dannyogolo No Life Poster Join Date: Nov 2002 Location: Nigeria Posts: 2,980 Member: 18200 Status: Offline Sonork: 100.1608286 Thanks Meter: 82	Auto PinFinder Power Problem This box seems ok to me, but as with all boxes, there are a few phones that it doesnt work ok. There are a few China phones that it cannot power. That is to say these phones comes up with battery, but not with pinfinder power cables. Its not a matter of connecting the cables correctly, the cables are always well connected (the batteries have the "+" and "-" indicators and its almost impossible to mistake them. Also the indicator red light behind the pin finder remains on while i try to power phone (showing that the polarity is correct). Maybe support should look at making it work with phone battery as well, or is there a way out ?

03-31-2008, 06:58	#15 (permalink)
milankumardoshi No Life Poster Join Date: Apr 2005 Location: Welcome Back J.A.F Age: 47 Posts: 533 Member: 135200 Status: Offline Sonork: 100.1594691 Thanks Meter: 33	problem detecting rx tx sir output#2 of pinfider has rj45 but the power terminal was given with 10 pin jack with 10 wires inside does it cause some problem.i get output 5 v

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Infinity Box + Auto Pinfinder Most powerful GSM Device with ALL FREE UPDATES !!!!	Infinity-Box	Main Sales Section	0	08-13-2008 18:21
Pinfinder Adaptor have powering problem ..	Gsm-W	Infinity-Box	18	08-03-2008 02:57
Auto Pinfinder Problem	asad_nomy7	Infinity-Box	10	05-24-2008 12:03
Auto pin finder power problem	cellbhai	Infinity-Box	6	02-25-2008 13:08
SGH-V200 auto power problem	ranjit2003	Samsung Hardware Repair	3	08-20-2006 21:53

03-14-2008, 18:21	#2 (permalink)
InfinitySupport Product Manager Join Date: Mar 2005 Location: infinity-box Posts: 38,635 Member: 130995 Status: Offline Thanks Meter: 35,227	Please, download latest PinFinder manual: http://www.infinity-box.biz/download..._PinFinder.pdf Please, see page 18: Automatic pinout detection: Troubleshooting I hope you can solve at least 99% of possible problems (especially with 8, 12, 14, 15 pins cables) with this instruction. One more link: http://www./showthread.php?t=512662

03-14-2008, 18:23	#3 (permalink)
targettelecom Freak Poster Join Date: Aug 2005 Location: china Posts: 182 Member: 170531 Status: Offline Thanks Meter: 8	this finder dont need to power on mobile ,its enugh give power for cpu and power ic to be can serach pinout .only when you make serach by finder need to stay press power key mobile untill find him. if not find that mobile so your mobile maybe not mtk .

03-14-2008, 22:13	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! some uniboxes have very small output voltage on pin1. Also 0,7 volts is dropping on transistor which swith power to phone. so at the end we get voltages below 3,7 volts which is not enough to power On phone if you have on pinfinder output voltage below 3,7v- please modify your unibox there must be diode removed and set shortcut. Where is located this diode you can find in pin finder user manual in troubleshooting section

03-29-2008, 17:54	#7 (permalink)
navin71 No Life Poster Join Date: Dec 2004 Location: india Age: 49 Posts: 544 Member: 101891 Status: Offline Thanks Meter: 277	sir i have connected auto pinfinder to the pc with infinity box but while connecting it shows error like this dongle is not activated for current software module curent dongle activation lavel 0001 required dongle activation lavel 0011 download lattest dongle manager from support area but when connecting through dongle manager it shows like this:- ----------Process started:10:17:20 PM---------- Locating Emeralda server... Emeralda server#1 address found. Connecting to Emeralda server#1... Server connection successfully established. S/N: *******Firmware: *** Authenticating on server... Authentication successfull. Checking upgrade client version... Your upgrade client is up-to-date. Checking Dongle Identification... Dongle Identification checked. Activating module... Module check error: Server reported error:[0044] Module S/N is already registered. Don't try more !

03-29-2008, 21:01	#8 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! need same log file but with full dongle detales to mailbox: [email protected]

03-29-2008, 22:14	#9 (permalink)
mansi No Life Poster Join Date: Jan 2002 Location: Jordan Age: 46 Posts: 767 Member: 8664 Status: Offline Sonork: 100.1573507 Thanks Meter: 56	@dannyogolo maybe your phone is not MTK based, maybe its spreadtrum or something else. [which you cant auto detect pinouts] with standard cables come with pinout finder. one small advice: open phone and check CPU type [info is writen on cpu] if its MTK or not. BR Mansi

03-30-2008, 18:39	#11 (permalink)
::gsmcoder:: Cheater -Don't Deal with him- Join Date: Aug 2005 Location: /%%temp%%.;adb Posts: 3,652 Member: 172434 Status: Offline Sonork: 100.161280 Thanks Meter: 577	to me, pinout finder usage is not traumatic..................

03-30-2008, 19:37	#12 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello mr. navin71! please read user manual, there is all questins answered: http://www.infinity-box.biz/download..._PinFinder.pdf

03-31-2008, 05:41	#13 (permalink)
Faisal_Computer No Life Poster Join Date: Jun 2005 Location: Kamalia, Pakistan. Age: 38 Posts: 16,852 Member: 151871 Status: Offline Thanks Meter: 71,421	One Qua. when i try to connect mobile with BOX power its works fine with 80% mobiles and when i insert bettery or try to use Power Supply ( not from Box ) its gave this software version: 1.06 cable type: 1x8 (L8A) platform: MT6205, MT6217-MT6228 searching adapter at COM7... adapter found, version: 2000 pins: 8, plain power cycles: 1 activation cycles: 7 power-off delay: 20 start Rx/Tx: 1/1 Loading configuration... Initializing... Press and HOLD phone Power button now ! detecting pins... error: boot initialization step-2 failed: A0 19200 19200 19200 19200 19200 19200 19200 19200 19200 19200 19200 19200 19200 failed to detect pins time required: 28 sec Power Off ! so is this mean that we must use power from box ? and also some mobile can't power up even pinout finder find pins for example 2 or 3 days ago i got Lg Kg200 pinout finder detect pins ( power from BOX ) and i need to rebuild IMEI on power from box its can flash but when i try to rebuild imei mobile not powering up can you advice me how to solve this type of problems , on the box +tv i got 5 volts and works fine just i got these type of problems Br Faisal_Computer

03-31-2008, 06:05	#14 (permalink)
asad_nomy7 No Life Poster Join Date: Aug 2007 Location: Pakistan Posts: 2,306 Member: 570093 Status: Offline Thanks Meter: 1,067	bro faisal i think the power cable from the box work as GND pin also.and when we connect it other power source its not have GND pin then not detect RX/TX.