is Doro PhoneEasy 410gsm Supported? - GSM-Forum

FU_Too · 06-09-2011, 19:21

I see Doro PhoneEasy 410s is supported BUT cant see 410gsm. I tried unlocking by selecting 410s but get no response.

So I'm asking is Doro PhoneEasy 410gsm unlock supported by infinitybox?

YellowBoss · 06-10-2011, 04:31

Hello,

What is exact text from your phone back label ?

What cable/pinout you have used ?

Post here operation log text.

FU_Too · 06-10-2011, 10:40

Quote:

Originally Posted by YellowBoss

Hello,

What is exact text from your phone back label ?

What cable/pinout you have used ?

Post here operation log text.

I used pinout as 410s because looked the same board.

==== [09/06/2011 18:34:14] ====
COM77 [VCP0] selected
module v3.92
Action: read unlock codes
unlock method: read codes
Model: Doro-PhoneEasy-410s
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
error: can't activate test mode
error: operation failed !
Finished, time used: 48 sec
Remove/Install battery now !
No action is observed on fone

when I try read phone
Action: read/check information
Model: Doro-PhoneEasy-410s
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
error: connection failed !
If you are sure that cable is good - select another baudrate (f.e. set baudrate to "autodetect")
operation failed !
Finished, time used: 42 sec
Remove/Install battery now !

fone switches on but nothing happens on pc

FU_Too · 06-11-2011, 13:27

Is this phone Supported or Not???

YellowBoss · 06-13-2011, 23:37

Hello,

Sorry for late reply.

As I can see this phone has another mark in compare with ordinary 410s.
Could you, please, open phone and check what is this phone CPU chip name.

Also, try to type *#0044# w/o sim.
What you see at phone LCD ?

FU_Too · 06-14-2011, 10:11

Quote:

Originally Posted by YellowBoss

Hello,

Sorry for late reply.

As I can see this phone has another mark in compare with ordinary 410s.
Could you, please, open phone and check what is this phone CPU chip name.

Also, try to type *#0044# w/o sim.
What you see at phone LCD ?

I tried typing in that code without sim but nothing happens and if I press call button after then It says "English set"

I took photo of inside, hope that helps

YellowBoss · 06-14-2011, 12:05

Quote:

Originally Posted by FU_Too

I tried typing in that code without sim but nothing happens and if I press call button after then It says "English set"

I took photo of inside, hope that helps

Hello,

PCB is very similar to 410s (probably even the same) and I am sure that phone can be connected to software and at least we can read flash.
If phone can not be detected by software yet, please, double check pinout, (probably you have to swap Rx <-> Tx wires) and try to read full flash once again.
If you will be able to read flash - try to make "read codes" too.

Waiting for your results.

FU_Too · 06-14-2011, 13:56

Quote:

Originally Posted by YellowBoss

Hello,

PCB is very similar to 410s (probably even the same) and I am sure that phone can be connected to software and at least we can read flash.
If phone can not be detected by software yet, please, double check pinout, (probably you have to swap Rx <-> Tx wires) and try to read full flash once again.
If you will be able to read flash - try to make "read codes" too.

Waiting for your results.

I tried changing rx and tx but phone turned on when trying unlock so assumed was correct in begining so soldered connections to board and succes so can confirm 410gsm is same unlock as 410s although I didnt try direct unlock only codes.

Code:

COM9 [VCP0] selected
module v3.92
Action: read unlock codes
unlock method: read codes
Model: Doro-PhoneEasy-410s
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
error: boot initialization step #2 failed: 00
19200 autodetect
Initializing [6223:8A08]...
CPU: MT6223
chip: 0011:7B60:000C
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6223,E08
Date: 2000.00.00
Version: 1.0
Version: SHELL-S09_2V8_DORO410_L14EN_204_101020_MCP128+32_BT_FM_SMS
Version: CKT23D_08A_HW
80 byte(s) read
imei: 35759603383768
connection Ok
191 byte(s) read
38 byte(s) read
Phone lock: Off
Phone code: 1234
179 byte(s) read
reading data...
972 byte(s) read
lock[1] code: + 69947926
lock[2] code: + default
lock[3] code: + 1122
lock[4] code: - default
lock[5] code: - default
lock[6] code: + default
lock[7] code: + default
if phone do not ask for a code try: *983*8284#
if code is not accepted by phone:
- make full flash backup for emergency case
- flash phone with good eeprom file
- Power-On phone without sim-card
- Power-Off phone (do not remove battery)
- read unlock codes
- restore original imei
Finished, time used: 9 min 57 sec
Remove/Install battery now !

Thank you Very Much for your good support.

fonefun · 07-06-2011, 19:34

we made cables today for doro 409s and 410s should you need one

and yes it works on the 409gsm too, we unlocked the one pictured below

lot easier than soldering ;-)

available @ Acer Doro 409s - 410s Test Point Cable For Infinity Box

:::..CyBoRg..::: · 07-25-2011, 09:20

doro phoneeasy 409s gsm unlocked done via read codes........

COM7 [VCP0] selected
module v3.75
Action: read unlock codes
unlock method: read codes
Model: Doro-PhoneEasy-410s
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6223:8A08]...
CPU: MT6223
chip: 0011:5FED:000C
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6223,E08
Date: 2000.00.00
Version: 1.0
Version: SHELL-S21_1V8_DORO409S_L15EN_201_110107_MCP128+32_SMS
Version: CKT23D_08A_HW
80 byte(s) read
imei: 35682404008323
connection Ok
191 byte(s) read
38 byte(s) read
Phone lock: Off
Phone code: 1234
179 byte(s) read
reading data...
972 byte(s) read
lock[1] code: + 12345678
lock[2] code: + 56781234
lock[3] code: + 84064789
lock[4] code: - 3344
lock[5] code: - 5566
lock[6] code: + 7788
lock[7] code: + 9900
if code is not accepted by phone:
- make full flash backup for emergency case
- flash phone with good eeprom file
- Power-On phone without sim-card
- Power-Off phone
- read unlock codes
- restore original imei
Finished, time used: 1 min 17 sec
Remove/Install battery now !

YellowBoss · 07-26-2011, 09:23

Thank you very much for test report !
Each test report with attached logs is very important for us
so we can see how is Infinity-Box software works, what is phone hardware configuration (f.e. flash chip type)
and what is possible problems (so we will be able to fix it) and successfully done work.

06-09-2011, 19:21	#1 (permalink)
FU_Too No Life Poster Join Date: Feb 2004 Location: Devon, England Posts: 4,162 Member: 55766 Status: Offline Thanks Meter: 333	is Doro PhoneEasy 410gsm Supported? I see Doro PhoneEasy 410s is supported BUT cant see 410gsm. I tried unlocking by selecting 410s but get no response. So I'm asking is Doro PhoneEasy 410gsm unlock supported by infinitybox?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	18	12-23-2014 09:03
Is it possible to use the Nokia 6150 with the IR Port of a Toshiba Laptop?	telefonman	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	02-13-2000 20:06
Silly question!! Why is it impossible to read out the mastercode of Nokia phones????	MyKe	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	09-26-1999 14:31

06-10-2011, 04:31	#2 (permalink)
YellowBoss Product Supporter Join Date: Jun 2009 Location: private Posts: 36,476 Member: 1043909 Status: Offline Thanks Meter: 60,926	Hello, What is exact text from your phone back label ? What cable/pinout you have used ? Post here operation log text.

06-11-2011, 13:27	#4 (permalink)
FU_Too No Life Poster Join Date: Feb 2004 Location: Devon, England Posts: 4,162 Member: 55766 Status: Offline Thanks Meter: 333	Is this phone Supported or Not???

06-13-2011, 23:37	#5 (permalink)
YellowBoss Product Supporter Join Date: Jun 2009 Location: private Posts: 36,476 Member: 1043909 Status: Offline Thanks Meter: 60,926	Hello, Sorry for late reply. As I can see this phone has another mark in compare with ordinary 410s. Could you, please, open phone and check what is this phone CPU chip name. Also, try to type *#0044# w/o sim. What you see at phone LCD ?

07-06-2011, 19:34	#9 (permalink)
fonefun No Life Poster Join Date: Apr 2003 Location: Sheffield Posts: 709 Member: 26187 Status: Offline Sonork: 100:77458 Thanks Meter: 290	we made cables today for doro 409s and 410s should you need one and yes it works on the 409gsm too, we unlocked the one pictured below lot easier than soldering ;-) available @ Acer Doro 409s - 410s Test Point Cable For Infinity Box

07-25-2011, 09:20	#10 (permalink)
:::..CyBoRg..::: No Life Poster Join Date: Aug 2007 Location: inside the pcb board Posts: 544 Member: 568876 Status: Offline Thanks Meter: 99	doro phoneeasy 409s gsm unlocked done via read codes........ COM7 [VCP0] selected module v3.75 Action: read unlock codes unlock method: read codes Model: Doro-PhoneEasy-410s Checking data, wait... Phone should be Switched OFF ! Press and HOLD Power button now ! 19200 autodetect Initializing [6223:8A08]... CPU: MT6223 chip: 0011:5FED:000C status: FF Connecting at 19200, wait... Release Power button now ! Phone detected, wait... Hardware: MT6223,E08 Date: 2000.00.00 Version: 1.0 Version: SHELL-S21_1V8_DORO409S_L15EN_201_110107_MCP128+32_SMS Version: CKT23D_08A_HW 80 byte(s) read imei: 35682404008323 connection Ok 191 byte(s) read 38 byte(s) read Phone lock: Off Phone code: 1234 179 byte(s) read reading data... 972 byte(s) read lock[1] code: + 12345678 lock[2] code: + 56781234 lock[3] code: + 84064789 lock[4] code: - 3344 lock[5] code: - 5566 lock[6] code: + 7788 lock[7] code: + 9900 if code is not accepted by phone: - make full flash backup for emergency case - flash phone with good eeprom file - Power-On phone without sim-card - Power-Off phone - read unlock codes - restore original imei Finished, time used: 1 min 17 sec Remove/Install battery now !

07-26-2011, 09:23	#11 (permalink)
YellowBoss Product Supporter Join Date: Jun 2009 Location: private Posts: 36,476 Member: 1043909 Status: Offline Thanks Meter: 60,926	Thank you very much for test report ! Each test report with attached logs is very important for us so we can see how is Infinity-Box software works, what is phone hardware configuration (f.e. flash chip type) and what is possible problems (so we will be able to fix it) and successfully done work.