G6600 Unlock Problem - GSM-Forum

HighMoon · 01-24-2012, 19:36

I never had any problem to unlock Huawey G6600 but now i receive this message for the first time

Model: Huawei-G6600

Checking data**** wait...

Phone should be Switched OFF !

Press and HOLD Power button now !

9600 autodetect

error: boot phase #2/1 failed

Can not initialize test mode**** possible reasons:

1. communication fault**** repeat required operation

2. ffs/eeprom is seriously damaged**** use repair ffs/eeprom files or use another unlock/format method

error: operation failed !

Finished**** time used: 4 sec

Remove/Install battery now !

When the software say "Press and HOLD Power button now !" it doesn't wait for me to press but goes on to "autodetect".

The phone came from factory so is there any new firmware or so that we can't unlock for the moment?

Thanks in advance

BR

ourgh · 01-24-2012, 22:21

I have same probleme today i solvethe probleme by test point tx and rx and gnd and it work perfectly

HighMoon · 01-24-2012, 22:33

Hi.

Didi you use pinout as told in shell?

BR

InfinityHelp · 01-25-2012, 13:48

hello!

clearly this is wrong pinout problem.
Try to swap (change) with places your current Tx and Rx wires

01-24-2012, 19:36	#1 (permalink)
HighMoon Freak Poster Join Date: Aug 2008 Location: Portugal Posts: 261 Member: 836352 Status: Offline Thanks Meter: 12	G6600 Unlock Problem I never had any problem to unlock Huawey G6600 but now i receive this message for the first time Model: Huawei-G6600 Checking data** wait... Phone should be Switched OFF ! Press and HOLD Power button now ! 9600 autodetect error: boot phase #2/1 failed Can not initialize test mode possible reasons: 1. communication fault repeat required operation 2. ffs/eeprom is seriously damaged use repair ffs/eeprom files or use another unlock/format method error: operation failed ! Finished** time used: 4 sec Remove/Install battery now ! When the software say "Press and HOLD Power button now !" it doesn't wait for me to press but goes on to "autodetect". The phone came from factory so is there any new firmware or so that we can't unlock for the moment? Thanks in advance BR

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	23	01-07-2018 17:14
$50 Reward for unlocking my 6150!!!	TheDon	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	03-23-2015 14:21

01-24-2012, 22:21	#2 (permalink)
ourgh Freak Poster Join Date: May 2010 Posts: 110 Member: 1298112 Status: Offline Sonork: 100.1626550 Thanks Meter: 36	I have same probleme today i solvethe probleme by test point tx and rx and gnd and it work perfectly

01-24-2012, 22:33	#3 (permalink)
HighMoon Freak Poster Join Date: Aug 2008 Location: Portugal Posts: 261 Member: 836352 Status: Offline Thanks Meter: 12	Hi. Didi you use pinout as told in shell? BR

01-25-2012, 13:48	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! clearly this is wrong pinout problem. Try to swap (change) with places your current Tx and Rx wires