Gionee P4 dead - GSM-Forum

jatjag · 06-27-2015, 17:27

How can I revive dead dead Gionee P4 ?
Here is log,

Card found: S/N
Chinese Miracle II [MTK module] v 1.21

Operation : Check / Read Info [ v1.21 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 24 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
NAND_ID : 00B000B000B000B000B0000000000000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x87
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00BC

Error : DA init Failed! Error code : 0x5
LErr : EMICFG_NOT_FOUND

Boot Error!

Operation Failed
Elapsed: 00:00:08
Reconnect Power/Cable!

JayDi · 06-27-2015, 17:53

Repair HW first - seems as FlashIC damaged.

jatjag · 06-30-2015, 19:14

I reballed flash ic ,
Now it shows like following log,Can't flsh it.
How to solve?

Card found: S/N
Chinese Miracle II [MTK module] v 1.21

Operation : Check / Read Info [ v1.21 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 24 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42017ECAD80F411D
DA Stat : v4.2 on BBID : 0x87
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00BC

Error : DA init Failed! Error code : 0x5
LErr : EMICFG_NOT_FOUND

Boot Error!

Operation Failed
Elapsed: 00:00:09
Reconnect Power/Cable!

JayDi · 06-30-2015, 20:13

Now - use firmware and flash phone, or if you have dump - make Init Preloader first with dump.

jatjag · 06-30-2015, 20:34

I have scatter file downloaded from moulnisky.
I can't flash it.It gives boot error.
Can I initialise preloader with scatter file?

JayDi · 06-30-2015, 21:08

With Firmware flash via scatter CM2 will boot phone, if firmware support that flash ic.
Try init preloader by selecting ***preloader***.bin file from fw.

jatjag · 07-01-2015, 08:45

Getting this error for flashing as well as for int. preloader

Card found: S/N
Chinese Miracle II [MTK module] v 1.21

Scatter Load Ok , BaseBand : MT6582 , Project : gionee82_cwet_kk , Storage : EMMC
Files found : 14 , Set to Flash : 13
Ready to Flash!

Operation : Flash [ v1.21 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 24 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42017ECAD80F411D
DA Stat : v4.2 on BBID : 0x87
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00BC

Error : DA init Failed! Error code : 0x5
LErr : 00000BC0

Boot Error!

Operation Failed
Elapsed: 00:00:03
Reconnect Power/Cable!

PASSIONATE_BOYS · 07-01-2015, 09:19

Quote:

Originally Posted by jatjag

Getting this error for flashing as well as for int. preloader

Card found: S/N
Chinese Miracle II [MTK module] v 1.21

Scatter Load Ok , BaseBand : MT6582 , Project : gionee82_cwet_kk , Storage : EMMC
Files found : 14 , Set to Flash : 13
Ready to Flash!

Operation : Flash [ v1.21 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 24 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42017ECAD80F411D
DA Stat : v4.2 on BBID : 0x87
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00BC

Error : DA init Failed! Error code : 0x5
LErr : 00000BC0

Boot Error!

Operation Failed
Elapsed: 00:00:03
Reconnect Power/Cable!

Hello,
Try with this preloader attached, it's for Gionee P4 jellyBean.

Br.

JayDi · 07-01-2015, 09:50

Yes, this one will work for sure.

vinay233 · 10-03-2016, 18:56

Not work i also have dead gionee p4 sp tool show failed to enable dram and miracle show boot error

JayDi · 10-04-2016, 06:36

Quote:

Originally Posted by vinay233

Not work i also have dead gionee p4 sp tool show failed to enable dram and miracle show boot error

Do you really think someone care about this in Infinity section?

06-27-2015, 17:27	#1 (permalink)
jatjag No Life Poster Join Date: Jun 2004 Age: 51 Posts: 1,258 Member: 69514 Status: Offline Thanks Meter: 66	Gionee P4 dead How can I revive dead dead Gionee P4 ? Here is log, Card found: S/N Chinese Miracle II [MTK module] v 1.21 Operation : Check / Read Info [ v1.21 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 24 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6582 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0001 BB_CPU_NM : [MediaTek] MT6582_S00 Processing BROM stage SecCfgVal : 0x00000000 BromVersion : 0x05 BLVersion : 0xFE Preloader Status : Not active (Erased) Processing DA stage DA Select done , sending NAND_ID : 00B000B000B000B000B0000000000000 eMMC_ID : 00000000000000000000000000000000 DA Stat : v4.2 on BBID : 0x87 DRAM not initialized , configure DRAM Settings DRAM EmiReq Ok , 0x00BC Error : DA init Failed! Error code : 0x5 LErr : EMICFG_NOT_FOUND Boot Error! Operation Failed Elapsed: 00:00:08 Reconnect Power/Cable!

06-27-2015, 17:53	#2 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Repair HW first - seems as FlashIC damaged.

06-30-2015, 19:14	#3 (permalink)
jatjag No Life Poster Join Date: Jun 2004 Age: 51 Posts: 1,258 Member: 69514 Status: Offline Thanks Meter: 66	I reballed flash ic , Now it shows like following log,Can't flsh it. How to solve? Card found: S/N Chinese Miracle II [MTK module] v 1.21 Operation : Check / Read Info [ v1.21 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 24 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6582 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0001 BB_CPU_NM : [MediaTek] MT6582_S00 Processing BROM stage SecCfgVal : 0x00000000 BromVersion : 0x05 BLVersion : 0xFE Preloader Status : Not active (Erased) Processing DA stage DA Select done , sending NAND_ID : 00000000000000000000000000000000 eMMC_ID : 1501004B3758564D42017ECAD80F411D DA Stat : v4.2 on BBID : 0x87 DRAM not initialized , configure DRAM Settings DRAM EmiReq Ok , 0x00BC Error : DA init Failed! Error code : 0x5 LErr : EMICFG_NOT_FOUND Boot Error! Operation Failed Elapsed: 00:00:09 Reconnect Power/Cable!

06-30-2015, 20:13	#4 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Now - use firmware and flash phone, or if you have dump - make Init Preloader first with dump.

06-30-2015, 20:34	#5 (permalink)
jatjag No Life Poster Join Date: Jun 2004 Age: 51 Posts: 1,258 Member: 69514 Status: Offline Thanks Meter: 66	I have scatter file downloaded from moulnisky. I can't flash it.It gives boot error. Can I initialise preloader with scatter file?

06-30-2015, 21:08	#6 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	With Firmware flash via scatter CM2 will boot phone, if firmware support that flash ic. Try init preloader by selecting *preloader*.bin file from fw.

07-01-2015, 08:45	#7 (permalink)
jatjag No Life Poster Join Date: Jun 2004 Age: 51 Posts: 1,258 Member: 69514 Status: Offline Thanks Meter: 66	Getting this error for flashing as well as for int. preloader Card found: S/N Chinese Miracle II [MTK module] v 1.21 Scatter Load Ok , BaseBand : MT6582 , Project : gionee82_cwet_kk , Storage : EMMC Files found : 14 , Set to Flash : 13 Ready to Flash! Operation : Flash [ v1.21 ] ======= Flash 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 24 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6582 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0001 BB_CPU_NM : [MediaTek] MT6582_S00 Processing BROM stage SecCfgVal : 0x00000000 BromVersion : 0x05 BLVersion : 0xFE Preloader Status : Not active (Erased) Processing DA stage DA Select done , sending NAND_ID : 00000000000000000000000000000000 eMMC_ID : 1501004B3758564D42017ECAD80F411D DA Stat : v4.2 on BBID : 0x87 DRAM not initialized , configure DRAM Settings DRAM EmiReq Ok , 0x00BC Error : DA init Failed! Error code : 0x5 LErr : 00000BC0 Boot Error! Operation Failed Elapsed: 00:00:03 Reconnect Power/Cable!

07-01-2015, 09:50	#9 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Yes, this one will work for sure.

10-03-2016, 18:56	#10 (permalink)
vinay233 Junior Member Join Date: Aug 2016 Posts: 1 Member: 2616704 Status: Offline Thanks Meter: 0	Not work i also have dead gionee p4 sp tool show failed to enable dram and miracle show boot error