help problem flashing china e97 - GSM-Forum

tonywireless · 10-25-2010, 23:59

hi mr moderators and other experienced members pls i have a problem flashing china e97 ,it was detected successfully by the pin finder , but when i try to flash on the infinty software it gives me an error message log is below,how can i fix this problem then?

COM17 [VCP0] selected
module v3.24
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: reset settings ("format ffs")
ffs/eeprom backup enabled, it may takes several minutes !
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6235:8A04:8A01]...
CPU: MT6235
high speed boot On
chip: 0000:0000:0003
status: FF
boot packet size: 0400
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 11 sec
Remove/Install battery now !

InfinityHelp · 10-26-2010, 17:10

hello!

do you hold power button pressed long enough?
can you successfully read flash from this phone or you receive same error?

tonywireless · 10-27-2010, 04:22

yes i did so what do u think,is the solution sir,how and why should i read flash?

InfinityHelp · 10-27-2010, 20:19

hello!

reading flash may work at he same time while test mode is not.
checking flash reading could bring a light to issue of problem

10-25-2010, 23:59	#1 (permalink)
tonywireless No Life Poster Join Date: Apr 2009 Posts: 988 Member: 1012165 Status: Offline Thanks Meter: 116	help problem flashing china e97 hi mr moderators and other experienced members pls i have a problem flashing china e97 ,it was detected successfully by the pin finder , but when i try to flash on the infinty software it gives me an error message log is below,how can i fix this problem then? COM17 [VCP0] selected module v3.24 Device: Autodetect 6205-6239 NOR Checking data, wait... advanced flash detection enabled Action: reset settings ("format ffs") ffs/eeprom backup enabled, it may takes several minutes ! ====> Boot ... Press and HOLD Power button now ! 19200 fixed Connecting, wait... Initializing [6235:8A04:8A01]... CPU: MT6235 high speed boot On chip: 0000:0000:0003 status: FF boot packet size: 0400 Release Power button now ! in case of initial connection problem: on/off "Boot baudrate autoselect" Boot Fail Finished, time used: 11 sec Remove/Install battery now !

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
HELP!!! BACKGROUND SCREEN LOGO	Michael Go	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	11-23-2017 08:11
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
Eeprom dump lost, help needed.	CAMILO	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	11-29-2010 19:04
Help with 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	05-25-2009 16:29

10-26-2010, 17:10	#2 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! do you hold power button pressed long enough? can you successfully read flash from this phone or you receive same error?

10-27-2010, 04:22	#3 (permalink)
tonywireless No Life Poster Join Date: Apr 2009 Posts: 988 Member: 1012165 Status: Offline Thanks Meter: 116	yes i did so what do u think,is the solution sir,how and why should i read flash?

10-27-2010, 20:19	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! reading flash may work at he same time while test mode is not. checking flash reading could bring a light to issue of problem