Huawei G3512 unlock - GSM-Forum

microtel · 04-02-2012, 16:27

Huawei G3510 is on the shell list, but is it possible to unlock the model G3512 too, whit this setings?

InfinityHelp · 04-02-2012, 20:48

hello!

please use Mmodule and do "read detailed information" in service Tab.
post this info here, we will check it and reply what to do next

microtel · 04-04-2012, 14:21

I cant read out a detailed information, i soldered directly rx tx and gnd to pcb, com speed auto. Idea?

InfinityHelp · 04-04-2012, 16:00

hello!

wrong pinout? Common mistake is tx/rx position. Try to swap with places tx/rx wires

DeDaMrAz · 04-20-2012, 22:04

Action: read/check information
Model: _Autodetect MT6228-6268 NAND
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
baud set to: 115200
Phone detected, wait...
Hardware version: MT6252"
Hardware version: HUAQIN52_6432_10A_HW
Software version: G3512S_V100R001B001C
Software date: 2000.00.00
Barcode: V3N6RB1221504188 111
imei-1: 867775002152279
Finished, time used: 2 sec
Remove/Install battery now !

phone can`t be booted for detailed info reading...

YellowBoss · 04-20-2012, 23:20

Hello,

We hope to release updated software for this CPU type in nearest future.
If you have an ability to keep phone with you for 2-3 more days, pls send a mail to rd@infinity-box.com and include link to this thread in your mail.
I can not promise for sure, but we will try to release updated software ASAP.

YellowBoss · 04-24-2012, 10:09

Quote:

Originally Posted by DeDaMrAz

Action: read/check information
Model: _Autodetect MT6228-6268 NAND
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
baud set to: 115200
Phone detected, wait...
Hardware version: MT6252"
Hardware version: HUAQIN52_6432_10A_HW
Software version: G3512S_V100R001B001C
Software date: 2000.00.00
Barcode: V3N6RB1221504188 111
imei-1: 867775002152279
Finished, time used: 2 sec
Remove/Install battery now !

phone can`t be booted for detailed info reading...

Hello,

Please, use this software, select "MT6252 NOR" and read full flash. Please, send full flash link or file to rd@infinity-box.com

http://www.infinity-box.com/download...dule_v4.26.rar

Thank you !

naseer_mansehra · 04-24-2012, 15:00

Mmodule _v4.26 not available in support last ver is 4.25

DeDaMrAz · 04-24-2012, 16:28

Read full flash

Code:

COM4 [VCP3] selected
module  v4.26
Device: _Autodetect MT6252 NOR
Checking data, wait...
Action: read flash NAND
interface: BROM_DLL_v3.1108.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6250:CA02:0100
status: FF
bbchip bl ver: FE
NOR flash id[0000]: 0000:000000000000 [AMD] AM29DL323D
chip size: 0Mb
otp status/size: S_DONE/00000000
NAND flash id[0000]: 0000:000000000000 [SAMSUNG] K9F5608Q0C
chip size: 0Mb
page/spare size: 0000/0000
pages per block: 0000
bits i/o: 00
address cycles: 00
internal RAM size: 00000000
external RAM [HW_RAM_UNKNOWN, CS0] size: 00000000
error: can not boot device: 0C0B:S_DA_UNSUPPORTED_BBCHIP
error: last error: 0C0B:S_DA_UNSUPPORTED_BBCHIP
Disconnect...
done
Finished, time used: 18 sec
Remove/Install battery now !

Read detailed info

Code:

COM4 [VCP3] selected
module  v4.26
Device: _Autodetect MT6252 NOR
Checking data, wait...
advanced flash detection disabled
Action: read/check information
====>  Boot ...
Press and HOLD Power button now !
115200 fixed
Connecting, wait...
Initializing [6250:CE00:0101]...
CPU: MT6250
high speed boot On
chip: 0000:0000:0007
status: FF
error: initialize step #1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 10 sec
Remove/Install battery now !

YellowBoss · 04-24-2012, 16:49

As I can see initial communication was good, but later phone stop to respond.
Please, try to press and HOLD phone Power button for a more long time during flash read process.

DeDaMrAz · 04-24-2012, 16:53

Same thing, no change in log... PWR pressed all the time...

Code:

COM4 [VCP3] selected
module  v4.26
Device: _Autodetect MT6252 NOR
Checking data, wait...
Action: read flash NAND
interface: BROM_DLL_v3.1108.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6250:CA02:0100
status: FF
bbchip bl ver: FE
NOR flash id[0000]: 0000:000000000000 [AMD] AM29DL323D
chip size: 0Mb
otp status/size: S_DONE/00000000
NAND flash id[0000]: 0000:000000000000 [SAMSUNG] K9F5608Q0C
chip size: 0Mb
page/spare size: 0000/0000
pages per block: 0000
bits i/o: 00
address cycles: 00
internal RAM size: 00000000
external RAM [HW_RAM_UNKNOWN, CS0] size: 00000000
error: can not boot device: 0C0B:S_DA_UNSUPPORTED_BBCHIP
error: last error: 0C0B:S_DA_UNSUPPORTED_BBCHIP
Disconnect...
done
Finished, time used: 18 sec
Remove/Install battery now !

nics121 · 07-23-2012, 21:04

Quote:

Device: _Autodetect MT6252 NOR
Checking data, wait...
Action: read flash NAND
interface: BROM_DLL_v3.1108.00

seems like trouble in this.
i have locked device, ready for test.

04-02-2012, 16:27	#1 (permalink)
microtel Freak Poster Join Date: Nov 2003 Location: Vojvodina Age: 34 Posts: 329 Member: 44395 Status: Offline Thanks: 27 Thanked 7 Times in 7 Posts	Huawei G3512 unlock Huawei G3510 is on the shell list, but is it possible to unlock the model G3512 too, whit this setings?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	23	09-16-2012 23:57
FAQ about unlock n0kia	man0n	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	6	11-29-2010 18:06
$50 Reward for unlocking my 6150!!!	TheDon	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	4	07-09-1999 22:08

04-02-2012, 20:48	#2 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Age: 36 Posts: 17,225 Member: 148515 Status: Offline Thanks: 2,319 Thanked 2,135 Times in 1,652 Posts	hello! please use Mmodule and do "read detailed information" in service Tab. post this info here, we will check it and reply what to do next

04-04-2012, 14:21	#3 (permalink)
microtel Freak Poster Join Date: Nov 2003 Location: Vojvodina Age: 34 Posts: 329 Member: 44395 Status: Offline Thanks: 27 Thanked 7 Times in 7 Posts	I cant read out a detailed information, i soldered directly rx tx and gnd to pcb, com speed auto. Idea?

04-04-2012, 16:00	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Age: 36 Posts: 17,225 Member: 148515 Status: Offline Thanks: 2,319 Thanked 2,135 Times in 1,652 Posts	hello! wrong pinout? Common mistake is tx/rx position. Try to swap with places tx/rx wires

04-20-2012, 22:04	#5 (permalink)
DeDaMrAz Freak Poster Join Date: May 2002 Location: Serbia Age: 31 Posts: 251 Member: 11604 Status: Offline Thanks: 18 Thanked 7 Times in 6 Posts	Action: read/check information Model: _Autodetect MT6228-6268 NAND Checking data, wait... Phone should be Switched ON ! Connecting, wait... baud set to: 115200 Phone detected, wait... Hardware version: MT6252" Hardware version: HUAQIN52_6432_10A_HW Software version: G3512S_V100R001B001C Software date: 2000.00.00 Barcode: V3N6RB1221504188 111 imei-1: 867775002152279 Finished, time used: 2 sec Remove/Install battery now ! phone can`t be booted for detailed info reading...

04-20-2012, 23:20	#6 (permalink)
YellowBoss Product Supporter Join Date: Jun 2009 Location: infinity-box Posts: 10,724 Member: 1043909 Status: Offline Thanks: 8,922 Thanked 25,248 Times in 2,396 Posts	Hello, We hope to release updated software for this CPU type in nearest future. If you have an ability to keep phone with you for 2-3 more days, pls send a mail to rd@infinity-box.com and include link to this thread in your mail. I can not promise for sure, but we will try to release updated software ASAP.

04-24-2012, 15:00	#8 (permalink)
naseer_mansehra Temporary banned !! Join Date: Dec 2008 Location: MANSEHRA<KPK> Posts: 697 Member: 921094 Status: Offline Sonork: 100.1603246 Thanks: 1,300 Thanked 260 Times in 173 Posts	Mmodule _v4.26 not available in support last ver is 4.25

04-24-2012, 16:49	#10 (permalink)
YellowBoss Product Supporter Join Date: Jun 2009 Location: infinity-box Posts: 10,724 Member: 1043909 Status: Offline Thanks: 8,922 Thanked 25,248 Times in 2,396 Posts	As I can see initial communication was good, but later phone stop to respond. Please, try to press and HOLD phone Power button for a more long time during flash read process.