infinity team please help about touch celebration - GSM-Forum

/\/\A/\/| · 04-30-2009, 12:53

COM4 selected
module v2.81
Action: touchscreen calibration
mode: 5
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:EF03:0009
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: M6225_00J6_HLD2_00_v03
Version: MT6225_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-5)...
0 done
214 byte(s) read
reading data #2...
writing data...
verification...
verification Ok
Finished, time used: 11 sec
Remove/Install battery now !

but still on pen celebration

**InfinitySupport** · 04-30-2009, 15:06

Hello,

Try to repeat calibration with other modes or with "reverse calibration" mode.

/\/\A/\/| · 04-30-2009, 22:57

Quote:

Originally Posted by InfinitySupport

Hello,

Try to repeat calibration with other modes or with "reverse calibration" mode.

sir i tried with other all mode and reverse calibration" show (error

**InfinitySupport** · 04-30-2009, 23:01

Quote:

Originally Posted by /\/\A/\/| DON

sir i tried with other all mode and reverse calibration" show (error

Hello,

What was the error exactly ?
Please, post here log.

/\/\A/\/| · 05-02-2009, 08:08

sir here is logs i checked after change imei but my problem is not solved

COM4 selected
module v2.81
Action: touchscreen calibration
mode: 4
Calibration order: reverse
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:EF03:0009
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: M6225_00J6_HLD2_00_v03
Version: MT6225_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-4)...
8 7 3 2error:
detection failed (4 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 7 sec

farihabest · 05-02-2009, 08:14

Quote:

Originally Posted by /\/\A/\/| DON

sir here is logs i checked after change imei but my problem is not solved

COM4 selected
module v2.81
Action: touchscreen calibration
mode: 4
Calibration order: reverse
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:EF03:0009
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: M6225_00J6_HLD2_00_v03
Version: MT6225_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-4)...
8 7 3 2error:
detection failed (4 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 7 sec

dear brohter....I always face this problem........but solution...is........

repeat the same mode......twice or three time ...
some mode gives error box and after this you can not close the window.Close the windiw in task manager and try again..

I also repair this with many time repeating... do not worry about this... try again and again until it removes.....

GSM-XPERTS · 05-02-2009, 08:19

yes i am full full agree with farihabest..

/\/\A/\/| · 05-03-2009, 08:21

Quote:

Originally Posted by farihabest

dear brohter....I always face this problem........but solution...is........

repeat the same mode......twice or three time ...
some mode gives error box and after this you can not close the window.Close the windiw in task manager and try again..

I also repair this with many time repeating... do not worry about this... try again and again until it removes.....

brother i check it many time but my prob is not solved but dont worry customer has gone so next time i think i got it so thanks brother

ehsas_ghum · 05-03-2009, 09:54

hi brother plz try with old chines miracle bcoz many user face bugs in new 2.81 plz try with 2.73 n then post thanks

/\/\A/\/| · 05-04-2009, 07:55

Quote:

Originally Posted by ehsas_ghum

hi brother plz try with old chines miracle bcoz many user face bugs in new 2.81 plz try with 2.73 n then post thanks

thanks brother next time i check with old version

shailccna · 05-06-2009, 17:43

yes sir there is bug in 2.80&2.81 so use 2.73

zeedan · 05-22-2009, 16:38

i have china mobile show ciliriting touch screen show any solution infinity team

ranagaurav · 05-22-2009, 17:10

new updates is not sucsess about tuch calibration

InfinityHelp · 05-22-2009, 22:21

Quote:

Originally Posted by zeedan

i have china mobile show ciliriting touch screen show any solution infinity team

hello!

if you can not calibrate display in ordinary way-
you can bypass it using option "bypass touchscreen calibration"
you must try all available methods (method-1, method-2 etc) until you succeed

biochemistali · 05-23-2009, 01:49

and more thing to add
this option does not going to repair touch system, only by passing touch checks from the software, so it is better to have all types of touch system that cost s aabpout 3 $ per touch system.
it is not good always to blame the team, one can do the dre to change the touch screen.

04-30-2009, 12:53	#1 (permalink)
/\/\A/\/\| No Life Poster $/\/\A/\/\|'s Avatar$ Join Date: Nov 2008 Location: Faisalabad pakistan Posts: 1,375 Member: 900083 Status: Offline Thanks Meter: 601	infinity team please help about touch celebration COM4 selected module v2.81 Action: touchscreen calibration mode: 5 Model: Autodetect 6205-6227 NOR Checking data, wait... Phone should be Switched OFF ! Press and HOLD Power button now ! 19200 autodetect Initializing [6225:8A03:8A00]... CPU: MT6225 high speed boot On chip: 0001:EF03:0009 status: FF Connecting at 19200, wait... Release Power button now ! Phone detected, wait... Hardware: MT6225,E03 Date: 2006.06.14 Version: 1.0 Version: M6225_00J6_HLD2_00_v03 Version: MT6225_GEMINI_HW detecting structure #2... 5 11 done 67 byte(s) read imei: 35044801123456 connection Ok detecting structure #5 (mode-5)... 0 done 214 byte(s) read reading data #2... writing data... verification... verification Ok Finished, time used: 11 sec Remove/Install battery now ! but still on pen celebration

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Infinity Team please help me to activate my pinfinder with my New Infinity Box	NawabN Sahoo	Infinity-Box	3	11-17-2009 13:50
infinity team please help about touch celebration	/\/\A/\/\|	Chinese Models & Cloned Phones	3	04-30-2009 12:22
infinity team please help about A898	babaformula	Infinity-Box	3	03-15-2009 09:34
Infinity Team Please help with my Infinity....	ASHRIFF	Infinity-Box	1	03-10-2008 16:51
infinity team plsssss help about c168i	rk19801	Infinity-Box	3	12-15-2007 21:18

04-30-2009, 15:06	#2 (permalink)
InfinitySupport Product Manager Join Date: Mar 2005 Location: infinity-box Posts: 38,635 Member: 130995 Status: Offline Thanks Meter: 35,227	Hello, Try to repeat calibration with other modes or with "reverse calibration" mode.

05-02-2009, 08:08	#5 (permalink)
/\/\A/\/\| No Life Poster $/\/\A/\/\|'s Avatar$ Join Date: Nov 2008 Location: Faisalabad pakistan Posts: 1,375 Member: 900083 Status: Offline Thanks Meter: 601	sir here is logs i checked after change imei but my problem is not solved COM4 selected module v2.81 Action: touchscreen calibration mode: 4 Calibration order: reverse Model: Autodetect 6205-6227 NOR Checking data, wait... Phone should be Switched OFF ! Press and HOLD Power button now ! 19200 autodetect Initializing [6225:8A03:8A00]... CPU: MT6225 high speed boot On chip: 0001:EF03:0009 status: FF Connecting at 19200, wait... Release Power button now ! Phone detected, wait... Hardware: MT6225,E03 Date: 2006.06.14 Version: 1.0 Version: M6225_00J6_HLD2_00_v03 Version: MT6225_GEMINI_HW detecting structure #2... 5 11 done 67 byte(s) read imei: 35044801123456 connection Ok detecting structure #5 (mode-4)... 8 7 3 2error: detection failed (4 tries) What to do: Try another calibration method, if still no luck: 1. make full flash backup for emergency case 2. make "format ffs" 3. Power-On phone 4. Power-Off phone by "Power" button (do NOT remove battery) 5. Repeat "Calibration" operation again 6. if still no luck read full flash and send to support with subject: touchscreen calibration failed error: can't read required data error: operation failed ! Finished, time used: 7 sec

05-02-2009, 08:19	#7 (permalink)
GSM-XPERTS No Life Poster Join Date: Mar 2009 Location: yasir telecom.. Age: 34 Posts: 1,062 Member: 1001830 Status: Offline Sonork: 100.1652282 Thanks Meter: 242	yes i am full full agree with farihabest..

05-03-2009, 09:54	#9 (permalink)
ehsas_ghum No Life Poster Join Date: Aug 2005 Location: Ena Neray Na Ho Dildar Ve Age: 37 Posts: 1,789 Member: 171512 Status: Offline Thanks Meter: 1,034	hi brother plz try with old chines miracle bcoz many user face bugs in new 2.81 plz try with 2.73 n then post thanks

05-06-2009, 17:43	#11 (permalink)
shailccna No Life Poster Join Date: Sep 2006 Location: some where in india Posts: 1,306 Member: 350232 Status: Offline Thanks Meter: 207	yes sir there is bug in 2.80&2.81 so use 2.73

05-22-2009, 16:38	#12 (permalink)
zeedan No Life Poster Join Date: Apr 2009 Posts: 1,434 Member: 1015645 Status: Offline Thanks Meter: 114	i have china mobile show ciliriting touch screen show any solution infinity team

05-22-2009, 17:10	#13 (permalink)
ranagaurav No Life Poster Join Date: Nov 2008 Location: gsm hosting Posts: 5,609 Member: 907098 Status: Offline Sonork: 100.1601140 Thanks Meter: 705	new updates is not sucsess about tuch calibration

05-23-2009, 01:49	#15 (permalink)
biochemistali No Life Poster Join Date: Oct 2005 Location: P A K I S T A N Age: 16 Posts: 1,387 Member: 190344 Status: Offline Thanks Meter: 280	and more thing to add this option does not going to repair touch system, only by passing touch checks from the software, so it is better to have all types of touch system that cost s aabpout 3 $ per touch system. it is not good always to blame the team, one can do the dre to change the touch screen.