Karbonn A4 Bad file detected! - GSM-Forum

***MyGSM World*** · 01-09-2015, 17:29

I Have 2 Phones With Network Problem, & 1 Is Working Well, So Decided To Read Flash File From Working Phone For Write To Faulty Phone.

Operation : Check / Read Info [ v1.08 ]

Code:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575_S00
Processing BROM stage
i2c Init : 00000000
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now ... 
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0065 , [TOSHIBA] TC58NYG0S8C
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0056 0000 0000
[NAND] : FLASH_LEN : 0x20000000
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Initial info read Ok!

Done!
Elapsed: 00:00:19
Reconnect Power/Cable!

Operation : Read Flash [ v1.08 ]

Code:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575_S00
Processing BROM stage
i2c Init : 00000000
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now ... 
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0065 , [TOSHIBA] TC58NYG0S8C
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0056 0000 0000
[NAND] : FLASH_LEN : 0x20000000
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 

Read Ok , collect info
Saved to : C:\InfinityBox\CM2MTK\Flash\6575_Temp_dump.ispff

Done!
Elapsed: 00:04:26
Reconnect Power/Cable!

When I Load Bin File.

Code:

Load File 
Bad file detected!

When I Click On "Flash"

Operation : Flash [ v1.08 ]

Code:

======= Flash
Files set for flashing : 
[ MCU ] : 

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575_S00
Processing BROM stage
i2c Init : 00000000
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now ... 
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0065 , [TOSHIBA] TC58NYG0S8C
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0056 0000 0000
[NAND] : FLASH_LEN : 0x20000000
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Automatically One Window Open With "CM2MTK" Name.

Code:

Cannot Open File ''''. The System Cannot Find The Path Specified.

Dzirt · 01-09-2015, 17:41

It is nand, what mean - it not supported for writing yet.

JorgeVla · 01-09-2015, 17:42

As i know, you can not write flash file in NAND-based phones

***MyGSM World*** · 01-09-2015, 17:52

Quote:

Originally Posted by Dzirt

It is nand, what mean - it not supported for writing yet.

My Dear Best Friend,

Any Way To Read NV File Of This Phone ?.

Dzirt · 01-09-2015, 18:02

NV , same as any other part for nand - lot of troubles. But will try make at least that.

***MyGSM World*** · 02-09-2015, 17:15

Dear Friends,

Karbonn A4 Have Two Version.

(1) [NAND] : FLASH_VEN : 0x0065 , [TOSHIBA] TC58NYG0S8C

(2) [NAND] : FLASH_VEN : 0x006E , [MICRON] MT29F1G16ABB

I Have Both Of Version Handset In My Hand.

1st One Handset With Full Network & IMEI Okay.

2nd One Handset With (No Service) & IMEI Okay.

So I Wanted To Read NVRAM From 1st One To Write 2nd One.

But It's Show This Error.

Operation : Write NVRAM [ v1.11 ]

Code:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575_S00
Processing BROM stage
i2c Init : 00000000
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now ... 
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x006E , [MICRON] MT29F1G16ABB
[NAND] : FLASH_DIE : 002C 00BC 0090 0055 0056 0000 0000
[NAND] : FLASH_LEN : 0x20000000
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Not supported FlashType yet for this operation !!!

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!

VIJAY2U2 · 02-09-2015, 17:41

As Far As I know Nand Writing Still No Supported

Code:

Chinese Miracle-2 MTK/MediaTek v1.11 released

MediaTek SP Platform
New feature supported: NVRAM Read/Write
- Read NVRAM data: MT6571-MT8392 (NAND/eMMC)
- Write NVRAM data: MT6571-MT6589, MT8312-MT8389 (eMMC only)

02-09-2015, 17:41	#7 (permalink)
VIJAY2U2 No Life Poster Join Date: Apr 2008 Location: India Posts: 3,541 Member: 1039903 Status: Offline Thanks Meter: 2,040	As Far As I know Nand Writing Still No Supported Code: Chinese Miracle-2 MTK/MediaTek v1.11 released MediaTek SP Platform New feature supported: NVRAM Read/Write - Read NVRAM data: MT6571-MT8392 (NAND/eMMC) - Write NVRAM data: MT6571-MT6589, MT8312-MT8389 (eMMC only)

01-09-2015, 17:41	#2 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	It is nand, what mean - it not supported for writing yet.

01-09-2015, 17:42	#3 (permalink)
JorgeVla No Life Poster Join Date: Feb 2010 Posts: 605 Member: 1228709 Status: Offline Thanks Meter: 268	As i know, you can not write flash file in NAND-based phones

01-09-2015, 18:02	#5 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	NV , same as any other part for nand - lot of troubles. But will try make at least that.