meizu m3s dead after flash CM2MT2!

[Steve-1]

the first state was power on with message upgrade error , now dead

and not accepte backup reflash

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM11)
MODE : PRELOADER PORT
PORT : 11
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000007
BROM : SecMode : SBC+SLA+SDA
BROM : PRELOADER PORT
MODE : Meizu : M3s_M5n_U10 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]

EMMC: 150100513832334D420085ABDE37734D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : Q823MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6750 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0008 , EVOL : 0x0000

RNID : E790F13358575CE115F285208EAC039E

DA : USB : HIGH-SPEED

Boot done!

Patch Level : LMY47I
Sec. Patch : 2017-04-05
Ver. CodeName : REL
Ver. Release : 5.1
Build Time : 1513908229
Board Platform : mt6750
Product Brand : Meizu
Product Manfct : Meizu
Display ID : Flyme 6.2.0.0G
Product Model : M3s
Product Name : M3s
Product Device : M3s
Product Board : M3s
Product Info : M3s

USERDATA : PLAIN ( NOT encrypted )

IMEI[0] : 861417030928687
IMEI[1] : 861417030928695
NVRAM check : Passed!

Done!
Elapsed: 00:00:32

Operation : Read Firmware [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM11)
MODE : PRELOADER PORT
PORT : 11
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000007
BROM : SecMode : SBC+SLA+SDA
BROM : PRELOADER PORT
MODE : Meizu : M3s_M5n_U10 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]

EMMC: 150100513832334D420085ABDE37734D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : Q823MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6750 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0008 , EVOL : 0x0000

RNID : E790F13358575CE115F285208EAC039E

DA : USB : HIGH-SPEED

Boot done!

Patch Level : LMY47I
Sec. Patch : 2017-04-05
Ver. CodeName : REL
Ver. Release : 5.1
Build Time : 1513908229
Board Platform : mt6750
Product Brand : Meizu
Product Manfct : Meizu
Display ID : Flyme 6.2.0.0G
Product Model : M3s
Product Name : M3s
Product Device : M3s
Product Board : M3s
Product Info : M3s

MT6750__Meizu__M3s__5.1__Flyme_6.2.0.0G__LMY47I__M 3s

Read : preloader.bin
Read : recovery.img
Read : custom.img
ExtSparse : Compression ratio : 90%
Read : proinfo.img
Read : md1rom.img
Read : md1dsp.img
Read : md1arm7.img
Read : md3rom.img
Read : nvram.bin
Read : lk.bin
Read : boot.img
Read : logo.bin
Read : tz.img
Read : secro.img
Read : system.img
ExtSparse : Compression ratio : 86%
Read : cache.img
Read : userdata.img

FW Size : 612.08 MB
Android Info saved : _Android_info.txt
Scatter : MT6750_Android_scatter.txt
Saved to : L:\GSM\MEIZU\m3s\MT6750__Meizu__M3s__5.1__Flyme_6. 2.0.0G__LMY47I__M3s\

Done!
Elapsed: 00:09:52

Created by Infinity-Box (c) 2019
Chinese Miracle II : MediaTek Service Module
Device Info file : _Android_info.txt

Patch Level : LMY47I
Sec. Patch : 2017-04-05
Ver. CodeName : REL
Ver. Release : 5.1
Build Time : 1513908229
Board Platform : mt6750
Product Brand : Meizu
Product Manfct : Meizu
Display ID : Flyme 6.2.0.0G
Product Model : M3s
Product Name : M3s
Product Device : M3s
Product Board : M3s
Product Info : M3s

Preloader [HW DEV] Info :
EMI : DEV : MT6755
EMI : SRC : preloader_y15.bin
EMI : CNT : 0007
EMI : [00] : eMCP : eMMC+LP/DDR3 , ID : 90014A484147326505 : VEN : HYNIX | DEV : HAG2e : RAM : [ 2.00 GB ]
EMI : [01] : eMCP : eMMC+LP/DDR3 , ID : 150100523231424D42 : VEN : SAMSUNG | DEV : R21BMB : RAM : [ 3.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100513832334D42 : VEN : SAMSUNG | DEV : Q823MB : RAM : [ 2.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 150100525831424D42 : VEN : SAMSUNG | DEV : RX1BMB : RAM : [ 3.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR3 , ID : 150100514531334D42 : VEN : SAMSUNG | DEV : QE13MB : RAM : [ 2.00 GB ]
EMI : [05] : eMCP : eMMC+LP/DDR3 , ID : 90014A484247346132 : VEN : HYNIX | DEV : HBG4a2 : RAM : [ 3.00 GB ]
EMI : [06] : eMCP : eMMC+LP/DDR3 , ID : 700100454841434541 : VEN : KINGSTON | DEV : EHACEA : RAM : [ 2.00 GB ]

Operation : Write Flash [ v2.06 ]

Repartition : Enabled
Flash Verify : Disabled
Reg.Pre-Erase : Enabled
Verify HW/SW : Enabled
SData Backup : Disabled
Safe UserData : Disabled

Files :16
[FL] : Set : recovery.img
[FL] : Set : custom.img
[FL] : Set : md1rom.img
[FL] : Set : md1dsp.img
[FL] : Set : md1arm7.img
[FL] : Set : md3rom.img
[FL] : Set : lk.bin
[FL] : Set : lk.bin
[FL] : Set : boot.img
[FL] : Set : logo.bin
[FL] : Set : tz.img
[FL] : Set : tz.img
[FL] : Set : secro.img
[FL] : Set : system.img
[FL] : Set : cache.img
[FL] : Set : userdata.img

[FL] : Total size : 0x25DC5468 [ 605.77 MB ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM11)
MODE : PRELOADER PORT
PORT : 11
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000007
BROM : SecMode : SBC+SLA+SDA
BROM : PRELOADER PORT
MODE : Meizu : M3s_M5n_U10 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]

EMMC: 150100513832334D420085ABDE37734D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : Q823MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6750 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0008 , EVOL : 0x0000

RNID : E790F13358575CE115F285208EAC039E

DA : USB : HIGH-SPEED

Boot done!

[FL] : HW verification passed!

SEC_DL : False (RAPHAEL)
OK
SEC_ID : 0x494E46494E495459424F584245535432

[FL] : Pre-Erase
Erase : 0x0000000000000000 : 0x00000000274C8000
Erase : 0x0000000028800000 : 0x0000000001000000
Erase : 0x0000000029B00000 : 0x0000000002400000
Erase : 0x000000002C400000 : 0x00000003769FBE00
ERR : 0xC0010002
ERR : ABORT
ERR : 0x00000000|0x00000000

Error : Flashing failed!
Seems as something wrong with device! Check battery charge and device state!

Reconnect Power/Cable!

[IDYSON]

Hello
Did you have any solution?
I'm having the same and exact problem.

[sahil2000ind]

UNTICK PRE ERASE AND TRY AGAIN

WBR
sahil2000ind

[IDYSON]

Thanks for the reply but it's still not working.