GSM-Forum

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   Infinity-Box (https://forum.gsmhosting.com/vbb/f296/)
-   -   Mobile Shot TDG9922 (https://forum.gsmhosting.com/vbb/f296/mobile-shot-tdg9922-360495/)

**RAJESH** 12-26-2006 07:04

Mobile Shot TDG9922
 
SIR...

SOLUTION FOR Mobile Shot TDG9922...TWO PISC HANG.....
PIN SOCKET SAME LG 8110,8120,.....


THANK YOU....

InfinitySupport 12-26-2006 08:42

Hi,

What is phone CPU name ?

**RAJESH** 12-26-2006 09:49

tahnk you for your reply...

SKYWORKS |
cx80501-31 |
e521418.1 |
0414 philippins |
ARM |
---------------------

flash ic lrs1806A

sir only two parts open and other parts are completly shild, i cnt see, shild removin highly risky..

thank you..

InfinitySupport 12-26-2006 10:16

Pls, more info about connector: is it 24 or 18 pins ?
if it's 24 pins, please try to read flash like Fly Z300 (SModule) and let me know about results.

**RAJESH** 12-26-2006 10:58

yes sir its 24 pin i will try to read give you result...
thank you...

allal123 08-20-2007 17:11

@InfinitySupport

hello
about MOBILE SHOT TDJ 9922
http://mobimir.ru/phones/img/mobileshot/tdg9922_s.jpg http://www.guide2net.net/mobile_inte...-9922_02_b.jpg

i think this thread is to very old 26th Dec 2006 06:04 :D

module : SModule v1.20
model selected : Fly Z300
speed baud rate : 460800 for all operations
phone prob : restart at startup
Cable name: uni cdma kyocera se47
connector: LG-7050
keyboard top
1.........24
12: Rx
13: Tx
14: Gnd
21: Vpp
------------------------------------------------------------------------
Code:

======================read eeprom==========================
COM4 [VCP1] selected
Device: Fly Z300
Checking data, wait...
Action: read eeprom
Boot...
Press and HOLD Power button now !
Connecting, wait...
Release Power button now !
Boot Done
Set baud...
460800
Set baud Done
Check Flash...
Check Flash Done
Check space...
Reading [eeprom_calibration]...
file saved: backup_eeprom_calibration_20070820-155114.41E.bin
Reading [eeprom_ffs]...
file saved: backup_eeprom_ffs_20070820-155557.41E.bin
Finished
Remove/Install battery now !
Time used: 330 sec

at now all is ok
Code:

================read full flash=====================
COM4 [VCP1] selected
Device: Fly Z300
Checking data, wait...
Action: read flash
Boot...
Press and HOLD Power button now !
Connecting, wait...
Release Power button now !
Boot Done
Set baud...
460800
Set baud Done
Check Flash...
Check Flash Done
Check space...
Reading [flash_part_1_of_2]...
file saved: backup_flash_part_1_of_2_20070820-160404.41X.bin
Flash ID1: 00B000B1
Reading [flash_part_2_of_2]...
file saved: backup_flash_part_2_of_2_20070820-161002.41X.bin
Flash ID2: 00B000B1
Finished
Remove/Install battery now !
Time used: 746 sec

also for read full flash all is ok
Code:

=======================sp-unlock===================
COM4 [VCP1] selected
Device: Fly Z300
Checking data, wait...
Action: unlock
Boot...
Press and HOLD Power button now !
Connecting, wait...
Release Power button now !
Boot Done
Set baud...
460800
Set baud Done
Check Flash...
Flash1: 00B000B1
Flash2: 00B000B1
Check Flash Done
Check space...
Reading [eeprom_configuration]...
file saved: backup_eeprom_configuration_20070820-161121.41E.bin
Reading [eeprom_calibration]...
file saved: backup_eeprom_calibration_20070820-161126.41E.bin
error: unsupported hardware: 01
Check space Fail
Finished
Remove/Install battery now !
Time used: 37 sec

i thinkit's SP-UNLOCK is supported because this phone is alredy unlocked
Code:

==========================reset setting=========================
COM4 [VCP1] selected
Device: Fly Z300
Checking data, wait...
Action: reset
Boot...
Press and HOLD Power button now !
Connecting, wait...
Release Power button now !
Boot Done
Set baud...
460800
Set baud Done
Check Flash...
Flash1: 00B000B1
Flash2: 00B000B1
Check Flash Done
Check space...
Reading [eeprom_calibration]...
file saved: backup_eeprom_calibration_20070820-161406.41E.bin
Reading [eeprom_ffs]...
file saved: backup_eeprom_ffs_20070820-161849.41E.bin
Check space Done
Write...
Write Done
Finished
Remove/Install battery now !
Time used: 366 sec

now it's prob , after reset setting phone can't power on (dead) :confused:
Code:

COM4 [VCP1] selected
Device: Fly Z300
Checking data, wait...
Action: flash write
Skip: Firmware
Skip: Flex/Customization
Skip: Resource pack
Skip: FFS/File system
Write: Eeprom
Boot...
Press and HOLD Power button now !
Connecting, wait...
Release Power button now !
Boot Done
Set baud...
460800
Set baud Done
Check Flash...
Flash1: 00B000B1
Flash2: 00B000B1
Check Flash Done
Check space...
Reading [eeprom_configuration]...
file saved: backup_eeprom_configuration_20070820-163148.41E.bin
Reading [eeprom_calibration]...
file saved: backup_eeprom_calibration_20070820-163153.41E.bin
Check space Done
Write...
Area: Eeprom
Erase: Eeprom
Write: Eeprom
Write Done
Finished
Remove/Install battery now !
Time used: 276 sec

now all is ok after reflash original eeprom ( phone turn on ):) and by miracle restart prob is solved and hanging at startup is solved and phone work well.

thx to infinity team for all his JOB , now i think this the first box to support this phone.:D

for more infos as always i am on ICQ and all files (eeprom+full back up) is uploaded on FTP .

sidali ;)

InfinitySupport 08-20-2007 19:48

Hello,

Thank you very much for good info and help !

salh1980 01-12-2008 16:41

plz i need the full flash for tdg9922 help

allal123 01-12-2008 17:46

Quote:

Originally Posted by salh1980 (Post 3011320)
plz i need the full flash for tdg9922 help

hi
i think u find it in INFINITY SUPPORT DOWNLOAD :)

salh1980 01-14-2008 11:41

he the file for tdg9922 not fond my problem after flashing my tdg9922 with z300 flash new is dead i need the full flash if same one have enyy tdg9922 plz red fulflash and send it for my thanks

salh1980 01-21-2008 15:12

plz if same one have tdg9922 read the fullflash and send it for me plz urgant


All times are GMT +1. The time now is 04:57.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -

Page generated in 0.13962 seconds with 6 queries

SEO by vBSEO