n99i can't write Eeprom - GSM-Forum

amr_ibrahim · 09-16-2008, 13:04

HI i have N99i restarting..
after format no network ...

and i can't flash it with this Eeprom files ..
MTK26_05C_MASTER_PCB01_GPRS_MT6226_S01.MAUI_05C_W0 6_16__ffs_01.B0E.bin
MTK26_05C_MASTER_PCB01_GPRS_MT6226_S01.MAUI_05C_W0 6_16__ffs_02.B0E.bin

always give me this error

Quote:

COM7 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
skip: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:7AC1:E802
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
slowest
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.F1F173AC.[MTK26_05C_MASTER_PCB01_GPRS_MT6226_S01.MAUI_05C_W0 6_16.BIN_C6630696].rpl
identification#1 detection finished
device-id: F1F173AC
identification#1 protocol ver: 04
ver. sw1: MTK26_05C_MASTER_PCB01_GPRS_MT6226_S01.MAUI_05C_W0 6_16.BIN
ver. sw2: MAUI.05C.W06.16, 69F99C39
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_F1F173AC_MTK26_05C_MASTER_PCB01_GPRS_MT6 226_S01.MAUI_05C_W06_16.BIN_C6630696_20080916-135420.B0X.bin
Area: Eeprom/ffs
flash: EC257E25082501:29EA0000000000
Write: Eeprom/ffs
error: no any expected answer
error: flash write error: 00E00000:00002000
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_F1F173AC_MTK26_05C_MASTER_PCB01_GPRS_MT6 226_S01.MAUI_05C_W06_16.BIN_C6630696_20080916-135557.B0X.bin
Finished, time used: 240 sec
Remove/Install battery now !

amr_ibrahim · 09-16-2008, 18:30

InfinityHelp this phone can't flash any Eeprom always give same error .....
pleas help me...

InfinityHelp · 09-16-2008, 20:15

hello!

what was initial phone problem?
for me it looks like bad flash soldering.
program cant write some part of eeprom

amr_ibrahim · 09-16-2008, 20:54

phone was restarting with sim or with out ...
i can't flash this phone also with same full flash file give me same error
but phone flashing without any problem with spiderman but sim 1 only is working sim2 no network ...

Quote:

for me it looks like bad flash soldering.

is that mean the problem is a hardware ?

JC_BY · 09-16-2008, 21:27

please tell me what pinout did you use?

amr_ibrahim · 09-16-2008, 21:45

i use this pin out
1............12
5=tx
6=rx
9=GND

InfinityHelp · 09-17-2008, 21:18

Quote:

Originally Posted by amr_ibrahim

phone was restarting with sim or with out ...
i can't flash this phone also with same full flash file give me same error
but phone flashing without any problem with spiderman but sim 1 only is working sim2 no network ...

is that mean the problem is a hardware ?

hello!

set first IMEI according IMEI label,
if this will not help with second SIM problem-
i think you must find second pinout and format it/restore IMEI

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
mc60 only buzz can't write eeprom	shaheen15	Martech CLIP / Box / Key	0	08-17-2006 13:27
PapuaUtils can't write EEPROM in M65	zahyr	S-Gold Based Phones	0	10-23-2005 18:44
Can't Write Eeprom	jesusangel	S-Gold Based Phones	1	03-01-2005 23:17
Can't write eeprom on Geo@i (MT-345)	tob	Mitsubishi	3	09-09-2003 23:20
I can't write EEPROM to C35 by any program! HELP!!!!!	VELCOM BY	x1x to x45/x50	38	06-04-2002 11:15

09-16-2008, 18:30	#2 (permalink)
amr_ibrahim Freak Poster Join Date: Feb 2005 Location: egypt Posts: 472 Member: 119435 Status: Offline Thanks Meter: 52	InfinityHelp this phone can't flash any Eeprom always give same error ..... pleas help me...

09-16-2008, 20:15	#3 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! what was initial phone problem? for me it looks like bad flash soldering. program cant write some part of eeprom

09-16-2008, 21:27	#5 (permalink)
JC_BY No Life Poster Join Date: Mar 2004 Location: BELARUS, Minsk Age: 44 Posts: 1,178 Member: 59319 Status: Offline Sonork: 100.1606948 Thanks Meter: 82	please tell me what pinout did you use?

09-16-2008, 21:45	#6 (permalink)
amr_ibrahim Freak Poster Join Date: Feb 2005 Location: egypt Posts: 472 Member: 119435 Status: Offline Thanks Meter: 52	i use this pin out 1............12 5=tx 6=rx 9=GND